Vivo STAND-V101GT User manual

Pneumatic Arm Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v101gt
SKU: STAND-V101GT
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
2.2-33lbs
(1-15kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Base
B(x1)
Pole
C(x1)
Cable Clip
S-A (x4)
M6x12mm
Screw
S-B (x1)
Spacer
S-C (x1)
M8x25mm
Screw
J (x1)
So Pad
K (x1)
Cover
L (x1)
Clamp Brace
M (x1)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualied technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x4)
M4x12mm
Screw
D(x1)
Arm Support
E(x1)
Lower Arm
F (x1)
Gas Spring
Arm
G(x1)
VESA Plate
H (x1)
Clamp Plate
I (x1)
Grommet
Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-B (x4)
M5x12mm
Screw
M-C (x4)
M5 Washer
T-C (x1)
6mm Allen
Wrench
T-A (x1)
3mm Allen
Wrench
T-B (x1)
4mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 1 - Option A - Clamp
Connect Clamp Brace (L) to Base (A) using M6x12mm Screws (S-A) and 4mm Allen Wrench (T-B).
Remove protective lm from So Pad (J) and apply to the underside of Clamp Brace (L). Loosen
the screws on the back of Lower Clamp (M) using 4mm Allen Wrench (T-B), leaving 6mm of thread
exposed.
Desk Thickness 0.4” to 2.25” (10mm-58mm)
Hang Clamp (M) into the top 4 slots on Clamp
Brace (L). Tighten rear screws with 4mm Allen
Wrench (T-B). Place Clamp Plate (H) on top of
the clamp bolts on Clamp (M).
Desk Thickness 2” to 3.35” (50mm-85mm)
Hang Clamp (M) into the lower 4 slots on
Clamp Brace (L). Tighten rear screws with 4mm
Allen Wrench (T-B). Place Clamp Plate (H) on
top of the clamp bolts on Clamp (M).
Install to desk and tighten clamp bolt using 6mm Allen Wrench (T-C). Snap Cover (K) onto the
back of assembled base.
T-B
T-B
L
I
S-A
L
A
L
T-B
T-C K
L
M
HH
M
T-B

4
STEP 1 - Option B - Grommet
Attach Grommet Plate (I) to Base (A) using M6x12mm Screws (S-A) and 4mm Allen Wrench (T-B).
Remove protective lm from So Pad (J) and apply to the underside of Grommet Plate (I).
Position Base (A) over grommet hole in desk. If there is no existing grommet hole, drill a 0.375”
(10mm) hole through the desktop in the desired mounting position.
Remove a single clamp bolt from Clamp (M) using 6mm Allen Wrench (T-C). Insert clamp bolt
with Clamp Plate (H) through the underside of the desk and secure to Base (A) using 6mm Allen
Wrench (T-C).
IA
T-B
I
J
T-C T-C
M
H
A
STEP 2
Screw Pole (B) into Base (A), and tighten set screws using 3mm Allen Wrench (T-A). Slide Pole Cable
Clip (C) onto Pole (B).
B
C
T-A
A
S-A

5
STEP 3
Slide Arm Support (D) onto Pole (B) and tighten using 6mm Allen Wrench (T-C). Place Lower Arm (E)
on top of Arm Support (D). Tighten set screw using 3mm Allen Wrench (T-A) to secure in place.
D
B
E
T-A
T-C
STEP 4
Place Gas Spring Arm (F) on top of Lower Arm (E), and tighten set screw on Lower Arm (E) using 3mm
Allen Wrench (T-A) to secure.F
ET-A
G
S-B
S-C
F
T-C
Connect VESA Plate (G) to Gas Spring Arm (F) using Spacer (S-B), M8x25mm Screw (S-C), and 6mm
Allen Wrench (T-C). Ensure that hexagon side of spacer is facing upward towards VESA Plate (G).
Remove Thumbscrew (G1) from back of VESA Plate (D). Separate Front VESA Plate (G2) from Back
VESA Plate (G3). Set aside.
G2
G3
G1

6
STEP 6
STEP 5
To mount the monitor, begin by lining up the tabs on Front VESA Plate (G2) with the slots on Back VESA
Plate (G3). Insert tabs into slots and re-install Thumbscrew (G1) into Back VESA Plate (G3) to secure.
Connect Front VESA Plate (G2) to back of
Monitor using appropriate Screws (M-A, M-B),
M5 Washers (M-C), and a Phillips Screwdriver.
M-A
M-B
M-C
G2
G2
G3
G1
STEP 7
While holding the arm in the horizontal position, adjust the gas spring tension using 6mm Allen
Wrench (T-C).
ARM DROPS - If the arm drops,
turn the adjustment screw counter
clockwise until it holds the monitor
in a horizontal position.
How to adjust if...
ARM RISES - If the arm raises up,
turn the adjustment screw lockwise
until it holds the monitor in a
horizontal position.
CAUTION - To avoid damage to the monitor and mount, always
keep the arm in a horizontal position while making adjustments.
T-C

7
STEP 8
Adjust as Desired
Remove cable cover on Gas Spring Arm (F) using
a Phillips screwdriver. Slide cable cover on
Lower Arm (E) forward to remove. F
E
Organize cables, then reinstall cable covers
to arms. Use Cable Clip (C) to route cables.
To adjust tilt tension, use 6mm Allen Wrench (T-C).
Store Allen
Wrenches
(T-A, T-B, T-C)
in Cover (K).
C
T-C

LAST UPDATED: 04/06/2023
REV2
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303