Vivo STAND-V001HG User manual

  
Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
 
phillips screwdriver
 
1
Scan the QR code with your mobile device or follow the link
to helpful videos and specifications related to this product.
 (x1)
Pole
 (x1)
Glass Base
 (x1)
Monito Am
 (x1)
VESA Plate
 (x1)
Decoative Cove
(x3)
M6x10
 (x3)
Connectin Bolt
! (x3)
M ashe
 (x1)
M10 Bolt
" (x1)
Suppot Plate
 (x1)
M10 ashe
 (x1)
Spin ashe
# (x4)
Rubbe Feet
 (x1)
ie Clip
$ (x1)
M4x6
 (x4)
M4x30
(x4)
M4 Space
 (x1)
ench
 (x1)
Soft Pad
 (x4)
M4x12
 (x1)
Allen Key
- -!$%%&& '#%$% &!

#( $
2
$  )   $
Attach Rubber Feet (m) to the underside of the Glass Base (b) (Figure
1). Attach Soft Pad (n) to the Pole (a) (Figure 2), and use a screwdriver
to poke holes for screws through the pad. Install Pole to Glass Base
using M6x10 Bolts (f), Connecting Bolts (g) and M8 Washers (h), and
tighten with medium Allen Key (u) and screwdriver (Figure 3). Slide
Decorative Cover (e) over the Pole.
*$  +! , )
$  )   $ -.
*$ , /0 ## , )
If the existing grommet hole comes with a plastic protector, first
remove it to ensure a flat mounting surface. Attach Soft Pad (n) to
Pole (a) (Figure 4). Position Pole on the mounting surface and secure
using the Support Plate (j) , M10 Washer (k), Spring Washer (l) and
M10 Bolt (i) (Figure ). Tighten using the Wrench (t), and slide
Decorative Cover (e) over the top of the Pole.
- *$ ,   ## , )
Determine mounting location on desktop and mark the center
drilling location. Drill a 3/8" (10mm) diameter hole through surface
at the marked location. Attach Soft Pad (n) to Pole (a) (Figure 6).
Position Pole on the mounting surface and secure using the
Support Plate (j), M10 Washer (k), Spring Washer (l) and M10 Bolt (i)
(Figure 7). Tighten using the Wrench (t), and slide Decorative Cover
(e) over the top of the Pole.
45
67

$ 1  !   !   2& #
Slide the monitor onto the head of Monitor Arm (c) as shown in the
diagram. Secure the VESA Plate (d) using M4x6 Bolt (p). Make sure
the bolt is installed before you rotate the monitor.
$ 3 ) #  ! 
Install Monitor Arm (c) to the Pole (a). Fasten the
bolt with supplied Allen Key (u). Attach the Wire
Clip (o) to the Pole (a) with the large Allen Key
(u).
$ 4 ! ! /   ! 
*$  5 ,

*$ , & ,

For monitor with flat back, attach
VESA plate (d) to monitor using
thumb screws (q).
For monitor with curved back,
attach VESA plate (d) to monitor
using M4x30 bolts (r) with
spacers (s).
3

If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no
missing or defective parts. Improper installation may cause
damage or serious injury. Do not use this product for any
purpose that is not explicitly specified in this manual. We
cannot be liable for damage or injury caused by incorrect
assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please contact
us. We are happy to replace parts to ensure you have a fully
functioning product.
 ( +
  
Last updated: 06/22/18
$ 6 " !     ! +
Tighten the grub screw in the Monitor Arm (c) using the small Allen
Key (u) to fix the tilting angle. Manage the cables and store tools
using the Wire Clip (o).
4