Vivo STAND-V001L User manual

Laptop Tray and Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001l
SKU: STAND-V001L/LW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
TOOLS NEEDED
22lbs
(9.98kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Pole
B(x1)
Clamp
C(x1)
Arm
H(x2)
Arm Cable Clip
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
VESA Plate
E(x1)
Laptop Tray
F (x1)
Grommet Base
G(x1)
So Pad
J (x1)
Pole Cap
I(x1)
Pole Cable Clip
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
S-A (x4)
M4x8mm
Screw
S-B (x4)
M4 Nut
S-C (x1)
M6 Nut S-D (x3)
M6x16mm
Screw
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
T-C (x1)
Wrench
M-A (x4)
M4x12mm
Thumbscrew
M-B (x4)
M4x30mm
Screw
M-C (x4)
M4 Spacer

3
ASSEMBLY STEPS
STEP 1
Option A: Desk Clamp Install
Loosen Clamp Bolt (B1) on Clamp (B). Install
Clamp (B) to Pole (A) using M6x16 Screws (S-D)
and 3mm Allen Wrench (T-A). Secure the clamp
assembly to the desktop.
Option B: Grommet Install
Using a Phillips screwdriver, remove the screw
from Clamp (B) and separate Clamp Bolt (B1)
and Clamp Plate (B2) from the clamp assembly.
Thread Clamp Plate (B2) onto Blamp Bolt (B1).
Install Grommet Base (F) to Pole (A) using
M6x16mm Screws (S-D) and 3mm Allen
Wrench (T-A). Remove adhesive backing
from So Pad (G) and stick it to the bottom of
Grommet Base (F).
If not using an existing through-hole for
mounting, use a 3/8” (10mm) drill bit to create
a mounting hole in the desired location. Thread
Clamp Bolt (B1) with Clamp Plate (B2) through
the mounting hole and into Pole (A).
B
A
T-A
S-D
B1
B
B1
B2
T-A
F
A
G
S-D
B1
B2

4
STEP 2
Slide Pole Cable Clip (I) and Arm (C) over Pole (A). Secure Arm (C) at the desired height using 5mm
Allen Wrench (T-B). Insert Pole Cap (J) into the top of Pole (A).
STEP 3
Attach Arm Cable Clips (H) to Arm (C).
I
J
C
T-B
H
C
A

5
STEP 4
Assemble VESA Plate (D) to Laptop Tray (E) using M4x8mm Screws (S-A) and M4 Nuts (S-B).
Tighten using Wrench (T-C) and a Phillips screwdriver.
Slide VESA Plate (D) with Laptop Tray (E) onto Arm (C). Secure the assembly in place using
M6 Nut (S-C).
Swivel and tilt assembled laptop tray to desired angle.
S-B
T-C
D
E
S-A
S-C
D
E
C

6
STEP 4
Attach VESA Plate (D) to the back of the monitor using M4x12mm Thumbscrews (M-A) or M4x30mm
Screws (M-B) with M4 Spacers (M-C).
Slide VESA Plate (D) with the monitor onto Arm (C). Secure the assembly in place using M6 Nut (S-C).
D
S-C
D
C
To use stand as single monitor mount, follow Steps 1-3, then return to these instructions to
proceed.
OPTIONAL USE: MONITOR MOUNT

7
STEP 6
Manage cables using Arm Cable Clips (I) and Pole Cable Clip (I).
STEP 7
Adjust the tilt using 5mm Allen Wrench (T-B).
H
I

LAST UPDATED: 05/17/2023
REV1.1L
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303