Vivo STAND-V002VA User manual

Dual Monitor Desk Mount with VESA Adapter Bracket
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002va
SKU: STAND-V002VA
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Pole
B(x1)
Clamp
C(x1)
Swivel Arm
D (x2)
VESA Plate
S-A (x3)
M6x16mm Screw
S-B (x2)
M6 Security
Nut
M-A (x8)
M4x12mm Thumbscrew
E (x1)
Grommet Base Plate
F (x1)
So Pad
G (x1)
Pole Cap
H (x8)
Extension
Bracket
I (x8)
“L” Support Holder
L(x1)
Pole Cable Clip
M (x4)
Arm Cable Clip
M-B (x8)
M4x30mm Screw
M-C (x8)
M6 Spacer
T-B (x1)
3mm Allen
Wrench
T-C (x1)
5mm Allen
Wrench
J(x8)
Plastic Cover
K(x8)
Compression
Pad
S-C (x16)
M4 Nut
S-D (x16)
M4x12mm
Carriage Bolt
S-E (x8)
M6x40mm
Screw
S-F (x8)
M6x60mm
Screw
S-G (x8)
M6x80mm
Screw
T-A (x1)
Wrench
ALTERNATIVE MOUNTING
HARDWARE
If Extension Brackets
are not used.
S-H (x8)
M5x45mm
Thumbscrew
TOOLS NEEDED
17.6 lbs
Per Arm
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver

4 5
OPTION A: Desk Clamp Install
Install the Clamp (B) to the Pole (A) using M6x16 Screws (S-A) and tighten using 3mm Allen
Wrench (T-B). Mount Clamp (B) to the desktop and tighten using the hand crank.
ASSEMBLY STEPS
STEP 1
STEP 2
Unscrew the hand crank of Clamp (B) to create an opening for the clamp to placed on desktop.
B
T-B
S-A
B
B
STEP 2 - Continued
Install Grommet Plate (E) to the Pole (A) using M6x16 Screws (S-A) and 3mm Allen
Wrench (T-B). Attach So Pad (F) to the Grommet Plate (E).
If desk does not have an existing grommet hole, drill a 3/8” (10mm) diameter hole at the desired
position through the mounting surface. Otherwise, you may use any existing 10-60mm gromment
hole.
Position Pole (A) on the mounting surface
and secure using the Clamp Plate (B2)
and Hand Crank (B1).
OPTION B: Grommet Installation
Use a Phillips screwdriver to loosen screw inside Clamp (B). Disassemble and separate the Hand
Crank (B1) and Clamp Plate (B2).
B
B1
B2
A
E
B1
A
B2
F
S-A
T-B

6 7
STEP 3
M
A
T-C
L
C
Slide Pole Cable Clip (L) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm (C) at desired height
using 5mm Allen Wrench (T-C). Insert Pole Cap (G) into top of Pole (A). Place Cable Clips (M) onto
Swivel Arm (C).
G
Attach “L” Support Holder (I) onto Extension Brackets (H) using M6 Screws (S-E, S-F, S-G) and a
Phillips screwdriver. Screw length will depend on thickness of your monitor. Thread M5x45mm
Thumbscrews (S-H) through Extension Brackets (H) and apply Compression Pads (K) to the ends of
the thumbscrews. Repeat for remaining Support Arms.
STEP 4
X4
S-E
S-F
S-G
I
K
H
S-H
Assembled extension brackest can be installed onto your monitor mount’s VESA plate in 3 dierent
setups. The optimal option varies depending on the shape and size of the monitor. Find the setup
that works best for your setup and follow steps on next page.
Option #1 Option #2 Option #3
OPTION #1
T-A
S-C
S-D
PROCEED TO STEP 5 ON PAGE 10
S-H
Install Extension Brackets (H) onto your VESA mount using M4x12mm Carriage Bolts (S-D),
M4 Nuts (S-C), and Wrench (T-A).
Place extension bracket assembly over monitor. Lightly tighten Thumbscrews (S-H) to secure
monitor. For best results, tighten until monitor feels secure, being careful not to over tighten. For
monitors that are thinner at the top than bottom, Thumbscrews at bottom should be tightened first,
with top Thumbscrews barely touching the monitor.
WARNING: Excessive tightening of upper compression screws
on ultraslim monitors can DAMGE YOUR SCREEN.
H

8 9
OPTION #2
T-A
S-C
S-D
PROCEED TO STEP 5 ON PAGE 10 PROCEED TO STEP 5 ON PAGE 10
Install Extension Brackets (H) onto your VESA mount using M4x12mm Carriage Bolts (S-D),
M4 Nuts (S-C), and Wrench (T-A).
S-H
Place extension bracket assembly over monitor. Lightly tighten Thumbscrews (S-H) to secure
monitor. For best results, tighten until monitor feels secure, being careful not to over tighten. For
monitors that are thinner at the top than bottom, Thumbscrews at bottom should be tightened first,
with top Thumbscrews barely touching the monitor.
WARNING: Excessive tightening of upper compression screws
on ultraslim monitors can DAMGE YOUR SCREEN.
OPTION #3
T-A
H
S-C
S-D
Install Extension Brackets (H) onto your VESA mount using M4x12mm Carriage Bolts (S-D),
M4 Nuts (S-A), and Wrench (T-A).
S-H
Place extension bracket assembly over monitor. Lightly tighten Thumbscrews (S-H) to secure
monitor. For best results, tighten until monitor feels secure, being careful not to over tighten. For
monitors that are thinner at the top than bottom, Thumbscrews at bottom should be tightened first,
with top Thumbscrews barely touching the monitor.
WARNING: Excessive tightening of upper compression screws
on ultraslim monitors can DAMGE YOUR SCREEN.
H

10 11
STEP 6
Slide monitor assembly onto Swivel Arm (C) and secure with M6 Security Screw (S-B).
To level monitors, remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws using 3mm
Allen Wrench (T-B). Once level, fasten M6 Security Nuts (S-B) back into place. Adjust the monitor tilt
using 5mm Allen Wrench (T-C).
S-B T-B
T-C
L
M
ADJUST AS DESIRED
C
CAUTION:
To avoid risk of monitors sliding o,
DO NOT rotate monitors beyond +5° or -5°.
Press Plastic Covers (J) over screw holes on “L” Support Holder (I). Route cables through Arm Cable Clips (M) and Pole Cable Clip (L).
STEP 5 CABLE MANAGEMENT
J
I
S-B

LAST UPDATED: 06/27/2023
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303