Vivo STAND-V002L User manual

Dual Monitor Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v002l
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V002L

2
PACKAGE CONTENTS
WARNING!
A (x2)
VESA Plate
B(x2)
Clamp
C(x1)
Base
M-A (x8)
M4x12
M-D (x8)
M5x16
J (x3)
Bolt
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
M-F (x8)
Spacer
M-E (x8)
D5 Washer
D(x1)
Pole
E(x1)
Pole
F (x1)
Pole Cap
G(x1)
Pole Connector
H (x2)
Cable Clip
I (x2)
Fastener
M-C (x8)
M5x12
M-B (x8)
M4x16
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
3mm Allen
Wrench
L (x1)
4mm Allen
Wrench
M (x1)
6mm Allen
Wrench

3
ASSEMBLY STEPS
STEP 1
Insert pole cap (F).
TOOLS NEEDED
Phillips
Screwdriver
STEP 2
Use allen wrench (L) on bolt (J) to secure the bottom pole (D) to the base (C).
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
F
E
D
C
J
L

4
STEP 3
Slide the cable management clip (H) down the pole followed by a single clamp (B). Choose your
desired height and secure the clamp to the pole with allen wrench (M).
STEP 4
Screw the pole connector (G) to the threads on top of pole (D) then add pole (E). Use allen wrench (K)
to tighten down the two screws inside the pole connector.
B
H
DM
K
D
G

5
STEP 5
OPTION A: Flat Back Monitor
Secure VESA plate (A) to the back of your monitor. Layer VESA plate on top of washer (M-E), then insert
correct size bolt to fit the holes in your monitor.
STEP 6
Add the second single clamp (B) to desired height and secure to the pole with allen wrench (M).
M
B
H
M- A
M- C
M- E
A

6
STEP 6 (Continued)
STEP 7
Slide the monitors onto (B) clamps. Use fasteners (I) to secure them.
OPTION B: Curved Back Monitor
Secure VESA plate (A) to the back of your monitor. Layer spacers (M-F), VESA plate, washers (M-E),
then insert correct size bolt to fit the holes in your monitor.
A
M- B
M- D
M- E
M- F
I

7
STEP 8
Adjust tilt angle with allen wrench (M).
STEP 9
Route wires through the cable management clips. Place allen wrenches into the cable management
clips for easy accessibility.
M
L
M
K

Last Updated: 04/26/2019
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654