Vivo STAND-V001C User manual

Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v001c
SKU: STAND-V001C/CW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please contact our product support team at 309-278-5303 or [email protected]om for
further assistance. Check carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for any purpose that is not
explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
22lbs
(8kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

3
PACKAGE CONTENTS
WARNING!
A (x1)
VESA Plate
B(x1)
Bracket
C(x1)
Clamp
M-A (x4)
M4x12mm
Screw
I (x1)
Support
Plate
T-A (x1)
4mm Allen
Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
D(x1)
Pole
E(x1)
Pole Cap
F (x1)
Cable Clip
G(x1)
Grommet Base
H (x5)
Pad
M-C (x4)
M5x12mm
Screw
M-B (x4)
M4x16mm
Screw
M-D (x4)
M5x16mm
Screw
M-E (x4)
M5 Washer
M-F (x4)
Spacer
T-B (x1)
6mm Allen
Wrench
S-B (x1)
Thumbscrew
TOOLS NEEDED
Phillips
Screwdriver
S-A (x3)
M6x16mm
Screw

4
ASSEMBLY STEPS
STEP 1
Attach Pole Cap (E) to top of Pole (D).
OPTION A: Desk Clamp Installation
Assemble Pole (D) to Clamp (C) with M6x16mm Screws (S-A) using 4mm Allen Wrench (T-A). Attach
Pads (H) to inside of Clamp. Secure to desktop.
STEP 2
10-88mm
D
E
Proceed to Step 3
on page 6
CH
S-A
T-A
D

5
OPTION B: Grommet Base Installation
Remove Clamp Screw (C1) and disassemble Clamp (C). Set aside Hand Bolt (C2).
STEP 2 - Continued
Attach Pads (H) to underside of Grommet Base (G). Note that the bottom of Grommet Base is the
side without a pin.
10-7 5 mm
Align pin on top of Grommet Base (G) with the small hole on the bottom of Pole (D), position over
hole in desktop, and attach to desktop using Clamp Bolt (C2) and Support Plate (I).
Proceed to Step 3
on page 6
C1
C2
GTop
Bottom
H
G
C2
I
D

6
STEP 3
Slide Cable Clip (F) and Bracket (B) onto Pole (D). Secure by tightening the side bolt using
6mm Allen Wrench (T-B).
B
F
D
T-B

7
OPTION A: Flat Back Monitor
Attach VESA Plate (A) to flat back monitors using appropriate Screws (M-A or M-C),
M5 Washers (M-E) and a Phillips screwdriver.
STEP 4 (Continued)
A
A
M-E
M-E
M-F
M-A
M-C
M-B
M-D
OPTION B: Recessed Back Monitor
Attach VESA Plate (A) to recessed back monitor using appropriate Screws (M-B or M-D), M5 Washers
(M-E), Spacers (M-F), and a Phillips screwdriver.
B

8
STEP 5
Slide the monitor onto the head of Bracket (B). Attach Thumb Screw (S-B). Make sure the screw is
attached before you rotate the monitor.
B
S-B

9
STEP 6
If needed, adjust the bolt on the side of the hinge behind the VESA plate to tighten or loosen
the tilt angle using the 6mm Allen Wrench (T-B).
T-B

10
STEP 7
Manage the cables using Cable Clip (F).
Allen Wrenches (T-A, T-B) in Cable Clip (F) for future adjustements.
F
T-B
T-A