Vivo MOUNT-VW03G User manual

Gas Spring TV Wall Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-vw03g
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: MOUNT-VW03G

2 3
ASSEMBLY STEPS
STEP 1
Remove VESA plate from the mount (A) by removing two bottom nuts with wrench (H) and loosening
top two nuts. The plate will li out from the slots on the top of the bracket.
PACKAGE CONTENTS
TOOLS NEEDED
17 - 66 lbs
(8 -30 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
B(x2)
Cover
M-F (x4)
D5 Washer
M-G (x4)
D8 Washer
M-H (x8)
Small
Spacer
W-A (x6)
Bolt
M-E (x4)
M8x50
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M8x20
M-D (x4)
M6x30
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x6)
Washer
W-B (x6)
Anchor
Drill
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 1-800-371-5654.
F (x1)
Allen Wrench
G(x1)
Allen Wrench
I(x1)
Bubble Level
M-I (x8)
Big
Spacer
A (x1)
Mount
C(x8)
Bolt
D(x2)
VESA Adapter
E(x2)
VESA Adapter
H(x1)
Wrench
STEP 2
OPTION A: Wood Wall
Use mount (A) to mark mounting holes on wall where stud is located. Using a 3/16” drill bit, drill
holes at least 2.2” deep into marked locations. Insert bolt (W-A) into top hole, leaving 3mm of thread
exposed. Hang top hole in mount over the bolt, and secure using two more bolts (W-A) with washers
(W-C). Tighten all bolts.
Pencil
NOTE: Do not use concrete anchors
(W-B) with wood studs.

4 5
STEP 2 (Continued) STEP 4
Secure VESA adapters (D, E) to VESA plate using bolts (C) in the appropriate conguration to match
your televisions mounting holes. NOTE: VESA adapters are not required for VESA patterns 200mm and
smaller.
STEP 3
Attach covers (B) to mount (A).
OPTION B: Concrete/Brick Wall
Use mount (A) to mark mounting holes on wall. Using a 3/8” drill bit, drill holes at least 2.4” deep into
marked locations. Press anchors (W-B) into holes, then insert bolt (W-A) into top hole, leaving 3mm
of thread exposed. Hang top hole in mount over the bolt, and secure using four more bolts (W-A) with
washers (W-C). Tighten all bolts.

6 7
STEP 5 Adjust as Desired
To adjust gas spring li strength, turn the screw on the top of the center joint using the large Allen
wrench (G). Clockwise will reduce strength, and counter-clockwise will increase. NOTE: If the mount
makes a popping noise when raising or lowering, tighten the socket set screw on top of the adjustment
screw. Adjust tilt joint using the smaller Allen wrench (F). Organize cables using the built-in cable
management clips.
If bolts are too long, spacers (M-H, M-I) may be required.
Attach VESA plate assembly to back of monitor using bolts (M-C, M-D, M-E) and washers (M-G).
STEP 6
Attach VESA plate to mount (A) using previously remove nuts and wrench (H) as shown in diagram.

Last Updated: 10/01/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654