Vivo STAND-V038M User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v038m
SKU: STAND-V038M
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
Phillips
Screwdriver
A (x1)
Arm
B(x1)
Pole
C(x1)
Pole Cap
D(x1)
Clamp
If you do not understand these directions, or if you have any doubts about the safety of the installation, please
call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly
specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
E(x2)
VESA Bracket
F(x1)
Grommet Plate
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x8)
M4X12mm Screw
M-B (x8)
M5x12mm Screw
M-C (X8)
M5 Washer
T-C (x1)
5mm Allen
Wrench
T-B (x1)
4mm Allen
Wrench
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury. 17.6lbs
(8kg)
PER ARM
T-A (x1)
Wrench
T-D (x1)
6mm Allen
Wrench
S-C (x4)
M8 Washer
S-D (x2)
M8 Nut
S-F (x3)
M6x16mm Screw
I (x6)
Arm Cable Clip
J (x1)
Pole Cable Clip
S-A (x4)
Bushing
S-B (x2)
M8x60mm Screw
G (x5)
So Pad
H (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
TOOLS NEEDED

3
ASSEMBLY STEPS
STEP 2
OPTION A: Clamp Installation
Stick So Pads (G) to the
underside of the Clamp (D).
Attach Pole (B) to Clamp (D) using
M6x16mm Screw (S-F). Tighten
using 4mm Allen Wrench (T-B).
Attach Clamp (D) to desktop .
OPTION B: Grommet Base Installation
For grommet hole mounting,
disassemble Clamp (D) using 4mm Allen
Wrench (T-B). Remove the screw and
plate from the clamp bolt, then remove
the clamp bolt. Stick So Pads (G) to the
bottom of the Grommet Plate (F). Slide
Support Plate (H) onto the clamp bolt
and insert bolt through the grommet
hole and Grommet Plate (F), then thread
into Pole (B).
STEP 1
Insert Pole Cap (C) to top of Pole (B).
T-B
D
S-F G
B C
T-B
F
G
H
D
B

4
STEP 3
Place Bushings (S-A) into holes at the ends of the Arms (A). Install VESA Brackets (E) onto Arm (A) with
M8x60mm Screws (S-B) and M8 Washers (S-C). Secure with M8 Washers (S-C) and M8 Nuts (S-D), and
tighten with 5mm Allen Wrench (T-C) and Wrench (T-A). Do not overtighten.
STEP 3
Slide Pole Cable Clip (J) and Arm (A) over the top of Pole (B) and tighten using the 5mm Allen
Wrench (T-C).
S-A
S-A
T-C
T-A
S-B
S-C
S-C
S-D
E
A
A
J
T-C

5
STEP 5
Attach Arm Cable Clips (I) to Arm (A) as shown.
STEP 6
Install Screws (M-A or M-B) and M5 Washers (M-C) to the top mounting holes of
your monitor, making sure to leave 3mm of threads exposed. Align Screws (M-A or
M-B) in monitors over slots in the VESA plates.
NOTE : Tighten the tilt support bolt when monitor is
being attached to prevent tipping.
I
A
M-A
M-B M-C

6
STEP 6 (Continued)
Secure using two more Screws (M-A or M-B) and M5 Washers (M-C) in the bottom two holes of each
monitor. Tighten all four screws using a Phillips screwdriver.
STEP 7
Adjust tilt support by loosening the screw on VESA Brackets (E) using 6mm Allen Wrench (T-D).
M-A
M-B M-C
E
T-D

7
STEP 8
Store Allen Wrenches (T-C, T-D) in Pole Cable Clip (J) for future use.
STEP 9
Adjust height of side monitors by turning the screw on top of each VESA Bracket (E) with the 5mm
Allen Wrench (T-C) as shown.
T-C
T-C
T-D
J
E

LAST UPDATED: 04/13/2022
REV2
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303