Volt Fat Boy Mini Spotlight User manual

INSTALLATION INSTRUCTIONS
VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
VOLT® Fat Boy Mini Spotlight
ITEM: VAL-2014-X-XXX
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®Fat Boy Mini Spotlight - VAL-2014-X-XXX
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
813.978.3700 • [email protected] • www.voltlighting.com
2
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS
PRODUCT DIMENSIONS
INSTALL STAKE
1
A. (1) Fixture Body
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on top
of the stake while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
GroundSoil
Stake
813.978.3700 • [email protected] • www.voltlighting.com
3
4.59”
2.2”
1.0”

INSTALL FIXTURE BODY TO STAKE
2
Wire Connections
3
VOLT® Fat Boy Mini Spotlight - VAL-2014-X-XXX
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
4
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the supply wires into
the wireway slot and attach the
xture on to the stake. Tighten
until snug.
Fixture
Body
Supply
Wires
Ground
Stake
Wireway
Slot
Strip both the leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Pigtail
Wire Connectors
Main Supply Cable

4
Install MR11 Bulb
5
813.978.3700 • [email protected] • www.voltlighting.com
5
Remove Glare Guard and Lens
Loosen the set screw and
remove the glare guard
and lens from the xture.
Glare Guard
Fixture
Lens
Set Screw
Insert MR16 bulb with the cor-
rect wattage and type marked
on the xture label and secure
into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
MR16 Lamp
Socket
Fixture

6
7
VOLT® Fat Boy Mini Spotlight - VAL-2014-X-XXX
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
6
813.978.3700 • [e-mail] • www.voltlighting.com
Install Lens
Place the lens and the glare
guard back onto the xture.
Align holes on both of them and
secure with previously removed
set screw. Hand tighten until
snug.
Glare
Guard
Lens
Fixture
Set
Screw
Adjust Luminaire Direction
Loosen the adjustment screw at
the joint and adjust the lumi-
naire to the desired direction.
Once the desired direction is
achieved, tighten the adjustment
screw.
ROTATE
Luminaire
Adjustment
Screw

VOLT® Fat Boy Mini Spotlight - VAL-2014-X-XXX
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
7
Install/Replace Lamp
Remove the glare guard and the lens to expose the MR16 lamp
and replace it with the correct wattage and type marked on the
xture label. Then, reinstall the lens and the glare guard.
IMPORTANT: MR16 lamp must be protected from moisture and
dust at all times. Always reinstall the lens and the glare guard
when removed.

Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • www.voltlighting.com
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)