Volt Sedona VHT-306-11-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT® Sedona Area Light
VHT-306-11-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2020, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Sedona Area Light
VHT-306-11-BBZ
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
!
!
www.voltlighting.com
- 2 -
This xture is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes
and instructions may result in serious injury, property damage and void
the warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or
servicing this xture.
2. Warning: this xture is not intended to be installed within 10 feet
[3 meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2
cm) in order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors
that are suitable for the application.
6. Position the wire connector so that it is located within 6 inches
(15.2 cm) from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or
shield.

Package Contents
Product Dimensions
[email protected] • 813.978.3700
3.5”
9.6”
11”
9”
- 3 -
22.15”
A. (1) Hat
Parts Sold Separately
A. (1) Decorative Arm
Decorative arm
sold separately

www.voltlighting.com
INSTALLATION INSTRUCTIONS
Remove Stem Top
1
- 4 -
Install Decorative Piece (optional)
Install Lamp
2
3
VOLT®Sedona Area Light
VHT-306-11-BBZ
Loosen the stem top
and remove it from the
top end of the stem.
Stem
To p
Stem
Place the decorative
piece onto the top end
of the stem as shown.
Stem
Decorative Piece
Insert the lamp with the correct
wattage and type marked on the
xture label and push rmly into
place.
CAUTION: Do not exceed maximum
wattage marked on xture label.
Socket
Lamp

[email protected] • 813.978.3700
- 5 -
Remove Washer and Finial
4
Install Stem Top
5
Install Coupler to Hat
6
Loosen the nial and remove
the nial, coupler and washer
from the stem top.
Finial
Stem Top
Coupler
Washer
Place the stem top over the
lamp and thread the stem
top onto the stem. Hand
tighten until snug.
Stem Top
Stem
Thread the coupler onto
the hat and hand tighten
until snug.
Hat
Coupler

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
Install Hat
7
Install Stake
8
VOLT®Sedona Area Light
VHT-306-11-BBZ
Thread the hat onto the stem
top and hand tighten until
snug.
Stem To p
Hat
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Stake
Soil
Ground

[email protected] • 813.978.3700
Wire Connection
10
Install/Replace Lamp
- 7 -
Install Stem to Stake
9
Clear away an area in the
ground at the wireway slot
on top of the stake. Lay the
luminaire pigtail into the
wireway slot and secure the
stem onto the stake. Tighten
until snug.
Stem
Stake
Pigtail
Wireway Slot
Strip both leads from the luminaire. Using two wire
connectors (sold separately), connect the leads from the
xture to the main supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
Remove the hat and stem top to expose the lamp and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the stem top and hat.
IMPORTANT: Lamps must be protected from moisture and dust at all
times. Always reinstall the stem top and hat when removed.

is-VHT-306-11-BBZ-ver2.pdf
Specications and product details subject to change without notice.
© Copyright 2020, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -