Volt LED Top Dog Tommy Light User manual

VOLT®Low Voltage Landscape Lighting
LED Top Dog Tommy Light
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2015, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT®LED Top Dog Tommy Light
Important: Please Read Before Installation
Important Safety Instructions
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet
(3.05M) or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
!
!
www.voltlighting.com

Package Contents
Parts Required (Sold Separately)
Product Dimensions
A. (1) Fixture
A. (3) Self-tapping Screws
B. (3) Wall Anchors
[e-mail] • 813.978.3700
5.5”
2.5”
C. (1) LED MR16 Lamp
Remove Shield and Glare Guard
1
Glare Guard
Shield
Screw
Fixture
Use a screwdriver to unlock the
screw. Then, remove the glare
guard from the shield. Next,
remove shield from the xture.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®LED Top Dog Tommy Light
Install Lamp
Install Shield and Glare Guard
2
3
Lamp
Screw
Socket
Shield
Glare Guard
Fixture
Insert lamp with correct wattage
and type marked on xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Replace the shield over the lamp
and thread onto the xture. Tighten
until snug. Attach the glare guard
back onto the shield and secure
with the screw. Tighten until snug
with a screwdriver.

[e-mail] • 813.978.3700
Install Fixture
4
Determine your desired location
for the xture. Pass self-tapping
screws through the holes on the
surface mount. Thread self-tapping
screws into wall surface to secure
the xture.
NOTE: Wall anchors (Sold
separately) are required for
brick walls or concrete walls. To
determine locations for the wall
anchors, place the surface mount
onto your desired location and
mark the points from the holes in
the mount.
Fixture
Self-tapping Screw
(Sold Separately)
Wall Anchor
(Sold Separately)
[Optional]
Wire Connections
5
Lay out the supply cable to the transformer. Strip two leads from
luminaire pigtail. Connect leads from luminaire supply cable to
transformer (sold separately).
Fixture
Pigtail
Transformer
(Sold Separately)
Supply Cable

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®LED Top Dog Tommy Light
Adjust Angle of Lamp
6
Install/Replace Lamp
Unscrew screws on glare guards and remove glare guards and shields to
expose the lamp and replace it with correct wattage and type marked on
xture label. And then reinstall shields and glare guards and tighten with
screws.
IMPORTANT: Halogen lamps must be protected from moisture and dust at all
times. Always re-install shields and glare guards when moved.
Adjustment
Screw
Loose adjustment screw and adjust
lamp to your desired angle and then
tighten adjustment screw.

Specications and product details subject to change without notice.
© Copyright 2015, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
is-182-ver1.pdf