Volt VAL-2044-L-ABK User manual

VOLT®Line Voltage Landscape Lighting
VOLT® Max All-Star 120V Lamp-Ready Spotlight
VAL-2044-L-ABK
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Line Voltage Landscape Lighting
VOLT® Max All-Star 120V Lamp-Ready Spotlight
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 2 -
Important: Please Read Before Installation
Important Safety Instructions
1. This LED Floodlight uses the latest in solid state lighting technology for
long life, low maintenance, and high efciency.
2. An internal power-factor-corrected switch mode supply allows this
xture to be used from any nominal 100V-277V, 60Hz AC supply without
any variation in light output.
3. Suitable for use in:
a. Ambient Temperatures of: -20~+40°C (-4~+104°F)
a. Wet Locations
Note: Save these instructions for future reference.
To avoid the risk of re, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualied electrician only, in
accordance with all applicable electrical codes.
To avoid electric shock:
1. Be certain electrical power is OFF before and during installation and
maintenance.
2. Luminaire must be connected to a wiring system with an equipment-
grounding conductor.
To avoid explosion:
1. Make sure the supply voltage is the same as the rated luminaire voltage.
2. Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
3. Do not operate in ambient temperatures above those indicated on the
luminaire.
For supply connections use wire rated for at least 90°C (194°F)
Warning: these luminaire should ONLY be installed by a qualied electrician.
!
!

Package Contents
Product Dimensions
A. (1) Stake
[email protected] • 813.978.3700
6.25”
7.75”
B. (1) Fixture
Remove Glare Guard
1
Loosen the set screw and remove
the glare guard from the xture
body.
REMOVE
Fixture Body
Set Screw
Glare Guard
7.75”
- 3 -

www.voltlighting.com
VOLT®Line Voltage Landscape Lighting
VOLT® Max All-Star 120V Lamp-Ready Spotlight
INSTALLATION INSTRUCTIONS
Remove Lens
2
Loosen Allen screws to remove
the washers and the lens from
the xture body.
Allen Screw
REMOVE
Fixture Body
Washer
Lens
Install Lamp
3
Insert the bulb with the correct
wattage and type marked on the
xture label and screw tightly
into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Lamp
Socket
Install Lens
4
Place the lens back onto
the xture body and
secure with the Allen
screws and washers.
Tighten until snug.
Allen Screw
Fixture Body
Washer
Lens
- 4 -

[email protected] • 813.978.3700
Install Stake and Conduit
6
Stake
Stabilizer
Grid
Install Glare Guard
5
Install the glare guard back
onto the xture body and
secure with previously
removed set screw. Hand
tighten until snug.
Fixture Body
Set Screw
Glare Guard
- 5 -
Conduit
Ground Level
Dig a hole in the ground for the conduit runs and the stake. Install
the conduit. Slide the stabilizer grid onto the stake and secure with
the screws. Place the stake over the conduit runs. Backll against the
mounting stake.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 6 -
Remove the cap from the stake
by loosening the set screws.
Remove Cap from Post
7
Set Screw
Cap
Stake
Thread the cap onto the xture
body and hand tighten until snug.
Install Cap to Fixture
8
Fixture
Cap
VOLT®Line Voltage Landscape Lighting
VOLT® Max All-Star 120V Lamp-Ready Spotlight

Wire Connection and Fixture Installation
9
Install/Replace Lamp
Please reverse Step 3 - Step 5 to expose the lamp and replace it with the
correct wattage and type marked on the xture label. Reinstall the lens
and glare guard.
Loosen the screw at the joint
and adjust the xture body to
the desired direction. Once the
desired direction is achieved,
tighten the set screw until snug.
Adjust Lamp Direction
10
Fixture Body
Set Screw
Set Screw
Cap
Post
Wire
Connector
Supply
Wires
Fixture
Wires
Allow enough wire from the
xture for adjustment purposes.
Connect the wires from
the xture into the wiring
terminal. The white wire goes
to the “Neutral” terminal; the
black wire goes to the “Live”
terminal; and the green wire
goes to the “Ground” terminal.
Fix them in place with the
connector screws.
[email protected] • 813.978.3700
- 7 -

IS-VAL-2044-LI.ver1
Specications and product details subject to change without notice.
© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -