Volt VWL-55 Series Operating and safety instructions

VOLT®Low Voltage Landscape Lighting
VOLT® Brass Bully Integrated LED Well Lights
VWL-55xxx Series
INSTALLATION & MAINTENANCE GUIDE
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT® Brass Bully Integrated LED Well Lights
VWL-55xxx Series
Important Safety Instructions: Read Before Installation
INSTALLATION & MAINTENANCE GUIDE
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminare, or
tting.
6. The main low voltage cable are intended for shallow burial - less than
6 inches (152 mm)
7. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
!
www.voltlighting.com
SAVE THESE INSTRUCTIONS

Package Contents
Product Dimensions
A. (1) Luminaire
B. (2) Optic
[email protected] • 813.978.3700
3”
3”
3”
Dig a Hole
1
Determine the luminaire placement
and use a shovel or post-hole diggers
to excavate a hole. Ensure that there
is at least 3” of space surrounding the
luminaire housing on all sides. This
space will be lled with pea gravel or
sand to assist in proper drainage.
Luminaire
Hole
* Ships with a 60° optic (installed). 35° optic optional.
Open
Shielded
Louvered

www.voltlighting.com
INSTALLATION & MAINTENANCE GUIDE
VOLT® Brass Bully Integrated LED Well Lights
VWL-55xxx Series
Strip both leads from the luminaire
pigtail. Using two wire connectors
(sold separately), connect the leads
from the luminaire to the main low
voltage supply cable leads.
Wire Connection
2
Pigtail
Wire Connectors
Main Low
Voltage Supply
Cable
Install the luminaire in the hole and
backll the hole with pea gravel or
sand.
Fill Pea Gravel or Sand
3
Pea Gravel
or Sand Luminaire
Soil

[email protected] • 813.978.3700
Unscrew the set screws from the
top of the luminaire. Remove the
faceplate and gasket from housing.
Remove Luminaire Cover and Gasket
4
Set Screws
Faceplate
Housing
Gasket
Remove the screw cap at the center
of the optic. Unscrew the screw,
then remove the optic from the
luminaire.
Put the new optic in the luminaire.
Reverse Step 6 then Step 4 to
reinstall all removed parts.
Replacing the Optic
6
Screw Cap
Optic
LED
Housing
Screw
Adjusting Light Position
5
Loosen the set screw. Use a
screwdriver to loosen and to tighten
the adjustment screw until desired
position is achieved. Tighten the set
screw to lock the position.
Reverse step 4 to reinstall removed
parts.
Set Screw
Adjustment Screw
Adjusting Light Position and Changing Optics

VOLT® Brass Bully Integrated LED Well Lights
VWL-55xxx Series
INSTALLATION & MAINTENANCE GUIDE
www.voltlighting.com

VOLT® Brass Bully Integrated LED Well Lights
VWL-55xxx Series
INSTALLATION & MAINTENANCE GUIDE
www.voltlighting.com

Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
is-vwl-55xxx-ver5.pdf