Volt VPL-1001-4-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT® Modernelle Cast Brass Path & Area Light
VPL-1001-4-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

[email protected] • 813.978.3700
VOLT®Modernelle Cast Brass Path & Area Light
VPL-1001-4-BBZ
INSTALLATION INSTRUCTIONS
- 2 -
Important: Please Read Before Installation
IMPORTANT SAFETY INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL Listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
!
!

[email protected] • 813.978.3700
www.voltlighting.com
Package Contents
Product Dimensions
A. (1) Fixture
1” 7”
2”
22”
Parts Required
A. (1) LED Lamp (sold separately)
Install Stake
1
Board
Stake
Soil
Ground
INSTALLATION INSTRUCTIONS
VOLT®Modernelle Cast Brass Path & Area Light
VPL-1001-4-BBZ
Install Bulb
3
Remove the diffuser from the
xture by unthreading the screws.
Attach the diffuser back onto the
xture and secure with screws.
Tighten until snug.
Insert the bulb with the correct
wattage and type marked on the
xture label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
Remove Diffuser from Fixture
Install Diffuser to Fixture
2
4
Fixture
Fixture
LED Bulb
Socket
Screw
Screw
Diffuser
Diffuser
- 4 - - 5 -
A. (1) Stake
Determine the desired location for mounting
the luminaire. Hammer the stake into the
ground until ange of stake is ush to grade.
To avoid damage to the stake, place a board on
top of the stake while hammering.
NOTE: If the ground is hard and stake is difcult
to install, make a crosscut in the ground using a
at shovel.

www.voltlighting.com
Install Fixture to Stake
5
Wire Connection
6
Fixture
Stake
Pigtail
Wireway Slot
Pigtail
Main Supply Cable
Wire Connectors
Install/Replace Bulb
Reverse Step 4 - Step 2 to expose the Bulb and replace it with correct
wattage and type marked on xture label. Reinstall Diffuser.
IMPORTANT: LED lamp must be protected from moisture and dust at all
times. Always reinstall diffuser when moved.
[email protected] • 813.978.3700
- 7 -
- 6 -
Clear away an area in the ground at the
wireway slot on top of the stake. Lay
the luminaire pigtail into the wireway
slot and screw the stem onto the stake.
If the assembly does not look straight,
adjust by pushing or pulling on the
stake only. Use a bubble level against
the side of the stem to make sure it is
perpendicular to the ground.
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main low voltage
supply cable leads.

- 8 -
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
IS-VPL-1001-ver2.pdf
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)