Volt VPL-1054 User manual

VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
V O LT ®Mini Round Wash Path & Area Light
ITEM: VPL-1054
INSTALLATION INSTRUCTIONS
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

V O LT ®Mini Round Wash Path & Area Light - VFL-1054
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3 meters]
of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that are
suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
813.978.3700 • [email protected] • www.voltlighting.com
2

PACKAGE CONTENTS
PARTS REQUIRED
813.978.3700 • [email protected] • www.voltlighting.com
3
PRODUCT DIMENSIONS
A. (1) Fixture Body B. (1) Allen Wrench
A. (1) G4 Bulb
B. Mounting Accessory
2.4”
1.87”
2.63” 3.15”
24.66”

REMOVE LENS
1
Install G4 Bulb
2
V O LT ®Mini Round Wash Path & Area Light - VFL-1054
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
4
Loosen the lens and remove it
from the xture body by rotating
it counter-clockwise.
Fixture Body
Lens
Insert G4 bulb with correct wattage and type marked on
xture label.
CAUTION: Do not exceed maximum wattage marked on
luminaire label.
OR
Socket G4 Bulb
Socket G4 Bulb
INSTALL LENS
3
Install the lens back onto the
xture body and hand tighten
until snug.
Fixture Body
Lens

INSTALL STAKE
4
Install MR11 Bulb
5
813.978.3700 • [email protected] • www.voltlighting.com
5
Determine the desired location for
mounting the xture. Hammer the
stake into the ground until ange of
stake is ush to grade. To avoid dam-
age to the stake, place a board on top
of the stake while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
Stake
Board
Ground
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the luminaire pigtail
into the wireway slot and screw
the xture body on to the stake.
Tighten the lock ring against the
stake and hand tighten until snug.
Fixture Body
Wireway Slot
Pigtail Lock Ring
Stake

WIRE CONNECTION
6
ADJUST LUMINAIRE DIRECTIONS
7
V O LT ®Mini Round Wash Path & Area Light - VFL-1054
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
6
Strip both the leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
By using the Allen wrench,
loosen the set screw at the
coupling. Rotate the coupling
with luminaire to your desired
direction. Tighten the set screw
with Allen wrench once your
desired direction is achieved.
Loosen the thumb screw at the
joint. Rotate the luminaire to
your desired direction. Tighten
the thumb screw once your
desired direction is achieved.
Coupling Set Screw
Luminaire
Allen Wrench
Thumb Screw
Luminaire

813.978.3700 • [email protected] • www.voltlighting.com
7
PACKAGE CONTENTS
Please reverse Step 2 - Step 3 to expose the G4 bulb and replace
it with the correct wattage and type marked on the xture label.
Then, reinstall the glare guard.
IMPORTANT: The G4 bulb must be protected from moisture and
dust at all times. Always reinstall the glare guard when moved.

Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • www.voltlighting.com
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)