Volt VHS-67 Series User manual

VOLT®Low Voltage Landscape Lighting
VOLT® LED Hardscape Lights
VHS-67XX Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®LED Hardscape Lights
VHS-67XX Series
Important Safety Instructions: Read Before Installation
INSTALLATION INSTRUCTIONS
!
www.voltlighting.com
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. DO NOT INSTALL in walls where the capstones overhang the wall less
than 3/4” [19mm] or under stairs where the tread overhangs the riser
less than 3/4” (19mm).
5. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
6. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminare, or
tting.
7. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
8. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
- 2 -
Package Contents
A. (1) Luminaire
B. (2) Self-tapping Screw
C. (2) Wall Anchors

[email protected] • 813.978.3700
- 3 -
Product Dimensions
4.2”
Install Mounting Plate
1
Brick or
Masonry Wall
Mounting Plate
Barrell Nut
Determine the desired location for
each luminaire before construction
of the wall is started.
Insert the stainless steel mounting
plate (sold separately), in between
the layers of hardscape material.
If prefered, use an adhesive or
mortar (sold separately), to secure
the luminaire in place.
.75”
7.2”
13”
19”
Install Luminaire in Brick or Masonry Wall
.75”
.75”
.75”

www.voltlighting.com
Install Luminaire
2
Mounting Plate
Shield
Route the luminaire wire
through the wall to the main
low voltage supply cable using
standard masonry procedures.
A “V” shaped notch can be cut
into the hardscape material
to aide in wire management.
Attach the shield and the
luminaire to the stainless
steel mounting plate by using
machine screws (ships with
mounting plate).
INSTALLATION INSTRUCTIONS
- 4 -
Strip both leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Luminaire Wires
Main Low Voltage
Supply Cable
Wire Connectors
Wire Connection
3
VOLT®LED Hardscape Lights
VHS-67XX Series
Luminaire
Mounting Screw

[email protected] • 813.978.3700
- 5 -
Install Luminaire in Railing, Deck Over-hang or Stair
Determine Luminaire Location
4
Determine the desired location for the luminaire.
Place the luminaire to the mounting surface and mark two points
on the mounting surface where the holes are on the ends of the
luminaire. The marks will be used for self-tapping screws or wall
anchors.
Note: Wall anchors are required for certain installation conditions
(brick wall, concrete wall, etc.)
A wireway hole may be drilled through the decking fascia or other
surface adjacent to the mounting surface.
A. Hold the luminaire in the desired mounting location. Mark the
location where the wire exits the luminaire.
B. Drill a hole through surface (suggested 1/4” [6.5mm] hole).
C. Thread the wire through the drilled hole.
Self-tapping
Screw
Luminaire
Railing, Deck
over-hang or Stair
Mark
Install from Bottom Install from Side
Self-tapping
Screw
Luminaire
Mark
Wireway
Hole
Railing, Deck
over-hang or Stair
Wireway Hole

www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 6 -
VOLT®LED Hardscape Lights
VHS-67XX Series
Install Luminaire
5
Install the luminaire and shield using provided self-tapping screws.
If the screws are dicult to install, mark holes and drill 1/8” pilot
holes.
If wall anchors are required, drill proper holes from the marks on
the mounting surface and then insert the wall anchors. Then install
the luminaire and shield and secure them with the self-tapping
screws.
Rubber washers are required during installation from the side.
NOTE: DO NOT OVER TIGHTEN SCREWS.
Return to Step 3 to complete the wire connections.
Self-tapping
Screw
Luminaire
Railing, Deck
over-hang or Stair
Mark
Install from Bottom Install from Side
Self-tapping
Screw
Luminaire
Mark
Wireway
Hole
Railing, Deck
over-hang or Stair
Wireway Hole
Shield
Shield Wall Anchor
Rubber
Washer

[email protected] • 813.978.3700
- 7 -
Adjust Lamp Direction
6
Using an Allen wrench, loosen the set screws on the ends of the
lamp and then rotate the lamp to the desired direction. Always
tighten the set screws after adjustments.
Allen Wrench
Set Screw
Set Screw Lamp

IS-VHS-67XX-ver2.pdf
Specications and product details subject to change without notice.
© Copyright 2018, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 8 -