Volt VHS-650-4-BBK User manual

VOLT®LOW VOLTAGE LANDSCAPE LIGHTING
V O LT ® Ultra Premium Cast Brass Up/Down Sconce
ITEM: VHS-650-4-BBK
INSTALLATION INSTRUCTIONS
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

V O LT ® Ultra Premium Cast Brass Up/Down Sconce - VHS-650-4-BBK
INSTALLATION INSTRUCTIONS
IMPORTANT: PLEASE READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
813.978.3700 • [email protected] • www.voltlighting.com
2
This luminaire is intended for installation in accordance with local codes and the National
Electric Code (NEC). Failure to adhere to these codes and instructions may result in
serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more
from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated
maximum of 300 watts (25 AMPS) at 15 volts.
4. Listed wire nuts must be suitable for wet locations and wiring connections must be
made with UL listed wire connectors that are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches
(15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches (152
mm).
7. If additional lengths of low voltage cable are required, please contact www.
voltlighting.com or call 1-813-978-3700.

PACKAGE CONTENTS
PRODUCT DIMENSIONS
REMOVE LENS
1
813.978.3700 • [email protected] • www.voltlighting.com
3
A. (1) Wall Mount
B. (2) Mounting Screws
C. (2) Wall Anchors
D. (1) Luminaire
3.5”
2”
7”
2” 4.25”
Twist the top and bottom lens to
remove them from the luminaire.
Lens
Lens
Luminaire

INSTALL BULB AND LENS
2
Remove Luminaire from Wall Mount
3
V O LT ®Ultra Premium Cast Brass Up/Down Sconce - VHS-650-4-BBK
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
4
Insert the bulbs (sold separately)
with the correct wattage and type
marked on the luminaire label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
NOTE: DO NOT touch bulb with
bare hands. Use soft cloth to
handle bulb.
Tighten the lenses back onto the
xture body.
Lens
Luminaire
Bulb
Lens
Bulb
Socket
Remove the mounting screws
off the top and bottom of the
luminaire and remove the
luminaire from the wall mount.
Luminaire
Wall Mount
Mounting Screw

Install Wall Mount
4
Wire Connection
5
813.978.3700 • [email protected] • www.voltlighting.com
5
Place the wall mount at the
desired location and mark two
points on the wall surface for the
wall anchors. Remove the wall
mount and drill the proper holes
on the wall.
Insert the wall anchors, into the
drilled holes. Pass the main low
voltage supply cable through the
center hole on the wall mount
and attach it onto the wall.
Secure with the lock screws.
Hand tighten until snug.
Wall Mount
Wall Anchor
Lock Screw
Main Low Voltage
Supply Cable
Using two wire connectors
(sold separately) connect
the supply wires from the x-
ture to the main low voltage
supply cable leads.
Main Low Voltage
Supply Cable
Supply Wire from
Luminaire
Wire Connectors

INSTALL LUMINIARE
6
V O LT ®Ultra Premium Cast Brass Up/Down Sconce - VHS-650-4-BBK
INSTALLATION INSTRUCTIONS
813.978.3700 • [email protected] • www.voltlighting.com
6
Carefully tuck all the wires
into the wall mount. Attach
the back of the luminaire
over the wall mount. Secure
it by threading the mounting
screws onto the top and
bottom of the luminaire
body.
Wall Anchor
Mounting Screw
INSTALL/REPLACE BULB
Remove the lens assembly off the luminaire body to expose the
bulb and replace it with the correct wattage and type marked on
the luminaire label. Reinstall the lens assembly.
IMPORTANT: Halogen bulbs must be protected from moisture
and dust at all times. Always reinstall the shade and lens when
removed.

813.978.3700 • [email protected] • www.voltlighting.com
7

Specications and product details subject to change without notice.
© Copyright 2023, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • www.voltlighting.com
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)