Volt VWL-510 Series User manual

VOLT®Low Voltage Landscape Lighting
VOLT® Articulator Cast Brass Integrated LED In-Ground
Well Light
VWL-510 Series
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)

VOLT® Articulator Cast Brass Integrated LED In-Ground
Well Light
VWL-510 Series
Important Safety Instructions: Read Before Installation
INSTALLATION INSTRUCTIONS
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire, or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact
www.voltlighting.com or call 1-813-978-3700.
!
www.voltlighting.com
SAVE THESE INSTRUCTIONS

Package Contents
Product Dimensions
A. (1) Luminaire
B. (1) PVC Tube
[email protected] • 813.978.3700
5.5”
6.3”
3”
3”
3”
0.7”
6.7”
Dig Hole
1
Dig a hole in the ground. Make sure
there are approximately 3” spaces
surrounding the PVC tube for pea
gravel or sand.
PVC Tube
Hole
Soil

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT® Articulator Cast Brass Integrated LED In-Ground
Well Light
VWL-510 Series
Place the luminaire into the PVC
tube. Pass the luminaire pigtail
through the PVC tube.
Strip both of the leads from the
luminaire pigtail. Using two wire
connectors (sold separately),
connect the leads from the luminaire
to the main low voltage supply cable
leads.
Wire Connection
Adjust Position of Light and Change Optics
2
Pigtail
Luminaire
PVC Tube
Wire Connector
Main Low Voltage
Supply Cable
Install the PVC tube with the
luminaire in the hole and ll the hole
with pea gravel or sand.
To Adjust Position of Light:
Loosen the knobs. Adjust the LED
housing to desired position. Tighten
the knobs, and place the luminaire
back into the PVC tube.
To Change Optics:
Loosen the knobs and remove the
LED housing from the holder.
Fill Pea Gravel or Sand
Remove Housing
3
4
Pea Gravel
or Sand
PVC Tube with
Luminaire
Luminaire
Grate
Knob
LED
Housing
Soil

[email protected] • 813.978.3700
Unscrew the cover and remove it
from the housing.
Remove Cover
5
Cover
Housing
Remove the screw cap at the center
of the optic. Unscrew the screw and
remove the optic from the luminaire.
Put a new optic into the luminaire.
Reverse steps 4 through 6 to reinstall
removed parts.
Replace Optic
6
Screw Cap
Optic
Housing
Screw

is-vwl-51023-ver3.pdf
Specications and product details subject to change without notice.
© Copyright 2017, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)