Vox power Nevo+1200 series User manual

NEVO+1200 Series

INSTALLATION MANUAL

_____________________________________________________________________________________________________

Page 1of 4Vox Power Limited | Unit 2, Red Cow Interchange Estate, Ballymount, Dublin 22, D22 Y8H2, Ireland | T +353 1 4591161 | www.vox-power.com

DOC-MN-002-05, NEVO+1200 Series Installation Manual

PLEASE READ THIS INSTALLATION MANUAL CAREFULLY BEFORE INSTALLING THIS PRODUCT AND KEEP THIS MANUAL FOR FUTURE REFERENCE.

All specifications are believed to be correct at time of publishing. Vox Power Ltd reserves the right to make changes to any of its products and to change or improve any part of the specification,

electrical or mechanical design or manufacturing process without notice. Vox Power Ltd does not assume any liability arising out of the use or application of any of its products and of any information

to the maximum extent permitted by law. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any products of Vox Power Ltd.

VOX POWER LTD DISCLAIMS ALL WARRANTIES AND REPRESENTATIONS OF ANY KIND WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF SUITABILITY, FITNESS

FOR PURPOSE, MERCHANTABILITY AND NONINFRINGEMENT.

Please consult your local distributor or Vox Power directly to ensure that you have the latest revision before using the product and refer to the latest relevant user manual for further information relating

to the use of the product. Vox Power Ltd products are not intended for use in connection with life support systems, human implantations, nuclear facilities or systems, aircraft, spacecraft, military or

naval missile, ground support or control equipment used for the purpose of guidance navigation or direction of any aircraft, spacecraft or military or naval missile or any other application where product

failure could lead to loss of life or catastrophic property damage. The user will hold Vox Power Ltd harmless from any loss, cost or damage resulting from its breach of these provisions.

Important installation information

This NEVO+1200 series of configurable power supplies are intended for use within end customer applications which restrict access to un-authorized personnel. The instructions in this manual

and all warning labels on the product must be adhered to carefully.

SAFETY

The NEVO+1200S/SL and NEVO+1200M/ML series are designed in accordance with the relevant safety requirements of IEC/EN/UL/CSA 62368-1, IEC/EN/UL/CSA

60950-1, IEC/EN/UL/CSA 60601-1, Low voltage Directive LVD 2014/35/EU and EMC directive EMC 2014/30/EU. All NEVO+1200 series power supplies must be

installed correctly in a controlled environment which restricts access to any un-authorised personnel. Equipment and system manufacturers must protect

service personnel against unintentional contact with the output terminals.

HAZZARDS

Dangerous voltages are present within the power supply.

It should only be handled by qualified personnel when the power supply has been disconnected from the mains supply voltage for more than 3 minutes.

External surfaces of the power supply may become extremely hot during and after operation. Appropriate care should be taken. If series and/or parallel

combinations of outputs exceed safe voltage and/or energy levels, the final equipment manufacturer must provide the appropriate protection for both users

and service personnel.

DE-RATINGS

Ambient

Temperature

•The input module power must be de-rated by 2.5%/°C above 50°C ambient up to a maximum ambient temperature of 70°C.

Input Voltage

•The input module power must be de-rated by 10W/VRMS below120 VRMS (1200W @ 120 VRMS, 850W @ 85 VRMS)

Remember to take the appropriate de-rating into consideration before specifying any NEVO+1200 power supply for an application.

If in any doubt, please contact Vox Power directly or your local Vox Power representative.

HEALTH AND SAFETY

To comply with section 6 of the health and safety at work act, a label that is clearly visible to service personnel must be placed on the final equipment. These

labels warn that surfaces of the power supply may be hot and should not be touched when the product is operating.

FUSING

The power supply has internal single pole fusing in the L (Live) line.

Fuses are not replaceable.

Damaged units should be returned to Vox Power for analysis and repair.

For Medical (60601-1) installations, the end application should provide an appropriately rated external fuse in the Neutral line.

DC operation is not covered by safety approvals. Contact Vox Power for details.

SERVICING

The power supply contains no user serviceable parts. Repairs must be carried out by authorised personnel only.

Contact Vox Power for further information.

APPROVAL

LIMITATIONS

NORTH AMERICA - When this product is used with 180V

–253V

mains where no neutral is present, connect the two live wires to L (Live) and N (Neutral) on the

input connector.

COOLING

For proper cooling of the power supply, the air intake and outlet must not be impeded. Allow 50mm clearance at both ends and position cabling appropriately.

EARTH TERMINAL

MARKING

To comply with the requirements of IEC/EN/UL/CSA 62368-1, IEC/EN/UL/CSA 60950-1 & IEC/EN/UL/CSA 60601-1, where the incoming wiring earth is intended

for connection as the main protective earth conductor and where the terminals for such a connection is not supplied on a component or subassembly, the user

shall add an appropriate label displaying a protective earth symbol in accordance with IEC60417-5019 (2006-08) directly adjacent to the terminal. The label

should be durable and legible and should withstand the 15 second rub test as per UL60950-1 section 1.7.15.

WARRANTY

Contact your sales agent or Vox Power for product repairs. See Vox Power standard terms and conditions for warranty conditions.

PRODUCT LABELS

The external product label contains information relevant to the power system. The label contains input voltage, maximum input current, input frequency,

maximum output power, fuse rating and type, serial number, approvals and product part number in form NEVO+1200x-yyyyyyyy-zzz.

NEVO+ OUTPUT

MODULES

Each output module label contains information relevant to that output. The label contains voltage adjustment range, maximum output current, serial number,

approvals and the part number in format OPx.

OTHER

•

A label warning that external surfaces are hot during operation and that the unit should be allowed to cool down properly should be placed on the unit

where such a label is clearly visible.

•The NEVO+1200 series is designed to comply with EMC standards but it does not imply that the end system will comply.

•To prolong the life of the unit, use in dust free environment.

•Units can sometimes be damaged during transit. In the event of transit damage, DO NOT connect power to the unit. Contact your sales agent or Vox

Power.

•Always use adequately sized cables and ensure good crimp connections. Use cable supports to minimise stress on connectors.

•

Avoid excessive shock or vibration.

Page 2of 4Vox Power Limited | Unit 2, Red Cow Interchange Estate, Ballymount, Dublin 22, D22 Y8H2, Ireland | T +353 1 4591161 | www.vox-power.com

DOC-MN-002-05, NEVO+1200 Series Installation Manual

Specifications

INPUT MODULE SPECIFICATION SUMMARY

Parameter

Details

Min

Typical

Max

Units

AC Input Voltage

Nominal range is 100V

RMS

to 240V

RMS

264

RMS

AC Input Frequency

Contact factory for 400Hz operation.

50/60

DC Input Voltage

Not covered by safety approvals. Contact Vox Power.

120

370

Output Power Rating

Standard & Medical (S/M) - De-rate linearly from 1200Watts at 120V

RMS

to 850Watts at 85V

RMS

Low Noise (SL/ML) - De-rate linearly from 900Watts at 120VRMS to 638Watts at 85VRMS

1200

900 Watts

Input Current

Standard & Medical (S/M) - 1200Watts output at 120Vrms input

Low Noise (SL/ML) - - 900Watts output at 120Vrms input

9 Amps

Fusing

Live line fused (5x20 Fast acting)

Amps

Power Factor

0.99

Size

154.5 (L) x 152.4 (W) x 41.0 (H) (see diagram for tolerance details)

Weight

720 + 60 per output module

Grams

Note 1.

Note 2.

NEVO+ input modules can only be used with NEVO+ output modules and must not be used for any other purpose.

Only use a power source of the type indicated on the product label.

OUTPUT MODULE SPECIFICATION SUMMARY

MODEL Output Voltage Output

Current

Rated

Power

Peak

Power

Load

Reg.

Line

Reg.

Cross

Reg.

Ripple &

Noise FPMH (1) Feature

Set (2)

Min.

Nom.

Max.

OP1

1.5V

7.5V

25A

125W

187.5W

±50mV

±5mV

±10mV

50mV

0.5

ABCDEFG

OP2

4.5V

12V

15V

15A

150W

225W

±100mV

±12mV

±24mV

120mV

0.5

ABCDEFG

OP3

24V

30V

7.5A

150W

225W

±150mV

±24mV

±48mV

240mV

0.5

ABCDEFG

OP4

18V

48V

58V

3.75A

150W

217.5W

±300mV

±48mV

±96mV

480mV

0.5

ABCDEFG

OP5

3.3V

12V

15V

2x 75W

±50mV

±12mV

±24mV

240mV

0.75

AFG

OP8

23.2V

24V

24.7V

3.125A

2x 75W

±100mV

±24mV

±48mV

480mV

0.75

AFG

OPA2

4.5V

12V

15V

25A

300W

375W

±100mV

±12mV

±24mV

120mV

0.5

ABCDEFGH

OPA3

24V

30V

15A

300W

450W

±150mV

±24mV

±48mV

240mV

0.5

ABCDEFGH

Note 1.

Output module, 30˚C base, 100% load, SR332 issue 2 Method I, Case 3, Ground, Fixed, Controlled

Note 2.

A = Remote Sense, B = External Voltage control, C = External constant current control, D = Current output signal, E = Current share, F =Over Voltage protection,

G = Over temperature protection, H = Dual Slot module

SAFETY SPECIFICATIONS

Parameter Details Max Units

Isolation Voltages

Input to Output (2 MOPP). Do not perform test on assembled unit(1)

4000

Input to Chassis (1 MOPP)

1500

Global signals (J2) to Output/Chassis

250

Output to Output/Chassis (Standard modules)

250

Earth Leakage Current

INDUSTRIAL: Normal condition, 264Vac, 63Hz, 25°C

1500

MEDICAL: Normal condition, 264Vac, 63Hz, 25°C

300

Touch Leakage Current

Standard modules NC/SFC

20/200

Patient Leakage Current

Standard modules 264Vac, 63Hz, 25°C NC/SFC

(2)

-----

Note 1. Testing an assembled unit to 4000V

may cause damage. Please refer to application note (APN-002) on Vox Power website or contact Vox Power representative.

Note 2. Not Applicable

INSTALLATION SPECIFICATIONS

Parameter Details Parameter Details

Equipment class

Flammability Rating

94V-2

Overvoltage category

Ingress protection rating

IP10

Material Group

IIIb (indoor use only)

ROHS compliance

2011/65/EU

Pollution degree

Intended usage environment

Home Healthcare (M/ML)/ Industrial (S/SL)

ENVIRONMENTAL SPECIFICATIONS

Parameter Details Non-Operational Operational Units

Min Max Min Max

Air Temperature

Operational limits subject to appropriate de-ratings

-40

+85

-20

70(1)

°C

Humidity

Relative, non-condensing

Altitude

-200

5000

-200

5000(2)

Air Pressure

104

52(2)

104

kPa

Noise Level

Standard Versions (S/M) - Variable. Measured 1m from fan intake.

Low Noise Versions (SL/ML) - Variable. Measured 1m from fan intake.

42 dBA

Shock

3000 bumps at 10G (16mS) half sine wave

Vibration

1.5G, 10 – 200Hz sine wave, 20G for 15min in 3 axes.

Notes

1. Derate input and all outputs at 2.5%/°C above 50°C.

2. 3000m & 68kPa for IEC/UL60601-1.

Page 3of 4Vox Power Limited | Unit 2, Red Cow Interchange Estate, Ballymount, Dublin 22, D22 Y8H2, Ireland | T +353 1 4591161 | www.vox-power.com

DOC-MN-002-05, NEVO+1200 Series Installation Manual

Mechanical Dimensions and Mounting

MECHANICAL DIMENSIONS AND MOUNTING

SCREWS

LOCATION

DETAILS

PENETRATION

TIGHTENING

MOUNTING M4

4mm max, including chassis

0.5 NM

OUTPUT MODULES M3 x 5, Countersink Posi, 16 Places Defined by screw 0.5 NM

CHASSIS LID AND FACEPLATE

M3 x 5, Countersink Posi, 9 Places

M3 x 30, Countersink Posi, 2 Places

Defined by screw 0.5 NM

Torque settings are for general reference only. The torque settings shown are the insert manufacturers recommended values.

Page 4of 4Vox Power Limited | Unit 2, Red Cow Interchange Estate, Ballymount, Dublin 22, D22 Y8H2, Ireland | T +353 1 4591161 | www.vox-power.com

DOC-MN-002-05, NEVO+1200 Series Installation Manual

Connector details

PINOUTS

Circuit

Details

J1 – Mains Input

Live

Earth

Neutral

J2a/b – Global Signals

Slot A/E - Power Good

Slot A/E - Inhibit

Slot B/F - Power Good

Slot B/F - Inhibit

Slot C/G - Power Good

Slot C/G - Inhibit

Slot D/H - Power Good

Slot D/H - Inhibit

Global Inhibit [A-D]/[E-H](GINH)

AC OK

+5V (Bias Supply 1A)

COM

J6 -Input Signals

Common

+5V 0.5A Bias (Always on)

Shut Down

Reserved

MATING CONNECTORS

Ref.

Details

Manufacturer

Housing

Terminal

J1 - Mains Input

3 Pin, Barrier, 6-32 steel Screws, 0.8NM or 7 Lb-In Torque

(1)

J2a/b - Global Signals 12 Pin, 2mm, 24-30 AWG, WIRE TO BOARD MOLEX(3) 0511101251 0503948051

Output Power(2)

Faston/Quick-Connect Tab – Size 6.35x0.8mm

VARIOUS(3)

VARIOUS

J6 - Input Signals

6 Pin, 1.25mm, with Friction Lock, 28-30AWG

MOLEX(3)

1510210600

50058800

Notes

1. Cable 14-18AWG, 300V, 16A, 105°C, use appropriately rated crimp terminal.

2. Terminal and wire current rating must exceed maximum short circuit output current. Eg. Output 1 = 25A*1.25 = 31.25A.

3. Direct equivalents may be used for any connector parts.

All cables must be rated 105°C min, equivalent to UL1015.

PART NUMBERS AND ORDERING INFORMATION

NEVO Power Series

NEVO+1200 S L - 1 1 2 2 3 3 4 4 - 0 0 0

Factory Use

Leakage Current

USE '0' for unused

slots. Blanking

plates will be

inserted at factory.

M = Medical,

S = Industrial

Fan

Blank = Standard,

L = Low Noise

Slot A - Output #

Slot H - Output #

Slot B - Output #

Slot G - Output #

Slot C - Output #

Slot F - Output #

Slot D - Output #

Slot E - Output #

Industrial input module has ITE approvals (IEC60950 & IEC62368), Medical input module has medical approvals (IEC60601)

Contact your Distributor or Vox Power for special configuration requirements. The factory may allocate a 3 digit suffix to identify such requirements.