Vox Valvetronix ToneLab LE User manual

Valvetronix
oneLab l
- m* ~--T
03 :
■
ISSiCJ".”"" BSt-JUSB” ""4—1““ A ___ ^
^3 S S “ogo'^P
—n _ 0 0 0 0 0 0
^7
_fxoh/off —J s”"”"'::;' 1 '*"; ™ -
SSj
rsifoiroiS
■ I
Owner’s Manual
(D©

Before using the product, be sure to read Lenovo Safety and General
Information Guide first.
Some instructions in this guide may assume that you are using
Windows® 10. If you are using another Windows operating system,
some operations may be slightly different. If you are using other
operating systems, some operations may not apply to you.
The features described in this guide are common to most models. Some
features may not be available on your computer or your computer may
include features that are not described in this user guide.
The illustrations in this manual may differ from the actual product.
Please refer to the actual product.
Regulatory Notice
• For details, refer to Guides & Manuals at http: / /support.lenovo.com .
First Edition (July 2015)
© Copyright Lenovo 2015.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General
forth in Contract No. GS-35F-05925.

WIRING DIAGRAM #1
The following diagram illustrates an intermixed LAF system. All stations connected to the
BG-1AC/PG-KC will receive all-call announcements and BGM. Substations must be connected to the
BG-1AC/PG-KC thru a 15 mfd bipolar capacitor as shown (if BGM/all-call is desired), or the system
will not work.

ISS Technology Update
David: HP has been

^Va— a“ t heelectronic
IMPORTANT In order to ensure perfect

Enter Password: In order to configure another adapter remotely, you’ll need to enter its
physical password first. Select the desired adapter from the list and click on the Enter
Password button.
The adapter’s password is printed on the back label.
Once the password is successfully entered, it will appear in the device list.

FRONT PANEL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
REAR PANEL
• 1
1 „ „„ AT 0 " A
125: — © l©@ oiee -m- Q j
20 21 22 23 24 25 26 27 28 29 30 31 32

7.3. Wall Mounting
Q

How to Use the Tuner Mode Control
rphe TUNER MODE control allows
to either ANTENNA, CABLE or AUTO
mode. It’s important for the TV to know
what type of signal to look for. (From a
Cable TV signal or a normal Antenna
signal.) In the AUTO mode, when the
AUTO PROGRAM feature is activated,
the TV will automatically choose the
Press the MENU button on the
<^> Press the CURSOR UP A or
<4> Press CURSOR UP ▲ or DOWN
I ▼ buttons to scroll the Install features
until the words TUNER MODE is
highlighted.
<§> Press the CURSOR RIGHT ^
| CABLE, or AUTO mode.
<§> When finished, press the STATUS
©
¥<
ion ANTENNA is
>9 are available.
When AUTO is seiec

i
Package Overview
This projector comes with all the items shown below. Check to make sure you
have them all. Contact your dealer immediately if anything is missing.
Security card User's guide (CD-ROM) Remote control
(Optional)
Downloaded From proiector-manual.com Acer Manuals

2
Sound level measurement
Conversion table
= 0.556. (”F-32)
°C = 32.0 °F)

3-6. Positoning Jumper Links (230/400V 3-Phase Models)

Monitor Block Diagram
The LCD MONITOR will contain an main board, an inverter/power board, keypad board and
internal adapter which house the flat panel control logic, brightness control logic and DDC.
The Inverter board will drive the backlight of panel and the DC-DC conversion.
The Adapter will provides the 12V DC-power to inverter/power board

Something not working
If the hob is not working correctly, please carry out the following checks before
contacting your local AEG Service Force Centre.
IMPORTANT: If you call out an engineer to a fault caused by incorrect use or
installation, a charge will be made even if the hob is under guarantee.
Sympton: Solution
There is no spark when lighting the
Check hob is connected to the
gas electricity supply. Check the fuse and
replace if necessery.
When the operating knob is released The operating knob has not been
the gas ring goes out again depressed long enough, or has not
been depressed sufficiently.
The gas ring bums unevenly Ensure the cover has been replaced
correctly, e.g. after cleaning.
If after all these checks, your hob still does not operate correctly, contact your
local AEG Service Force Centre.
In-guarantee customers should ensure that the above checks have been made a:
the engineer will make a charge if the fault is not a mechanical or electrical
breakdown.
Please note that it will be necessary to provide proof of purchase for any in¬
guarantee service calls.
17

17

0 Shuttle driver needle contact adjustment
Adjust so that the needle groove of the shuttle hook
thread guide O is at the center of the needle, slide the
thread guide lightly in, and then retighten the screws.
0 Shuttle hook thread guide adjustment
0 Two-step work clamp adjustment (independent presser foot solenoid type)
stopped.
(1) Lower the presser plate O. Loosen screw O and nut 0 to adjust the gap between the work clamp O and feed
plate 0 to 0 mm, and then tighten screw 0. Spring 0 will be minimally tensioned at this time.
Now tighten screw O and nut 0.
(2) Lift presser plate 0 again, and loosen nut 0. Adjust guide stud 0 so that the height from the needle plate top
to the work clamp O is 18 mm.

management application.
Amber, flashing A predictive failure alert has been received for this drive,
regularly (1 Hz) Rep | ace the dr|ve gs soon gs possib | e
expansion or stripe migration, but a predictive failure alert has
not replace the drive until the expansion or migration is
current operation and cause data loss.
Flashing irregularly
regularly (1 Hz)
Off
The drive is rebuilding, erasing, or it is part of an array that is
received for this drive. Replace the drive as soon as possible.
The drive is active, and it is operating normally.
A critical fault condition has been identified for this drive, and
A predictive failure alert has been received for this drive.
Server updates with an HP Trusted Platform Module
and BitLocker ™ enabled
When a TPM is installed and enabled in RBSU, and when the Microsoft® Windows® BitLocker ™ Drive
Encryption feature is enabled, always disable BitLocker ™ before performing any of the following
procedures:
• Restarting the computer for maintenance without a PIN or startup key
• Updating firmware (on page 81 )
• Upgrading critical early boot components
• Upgrading the system board to replace or remove the TPM
• Disabling or clearing the TPM
Common problem resolution 20