VuQube VQ1000 User manual

PORTABLE SATELLITE TV SYSTEM
VQ1000 OPERATION MANUAL

2Vu Qube
3
Vu Qube
Introduction
Congratulations on your purchase of the ultra-portable VuQube Satellite TV Antenna. The
VuQube is equipped with a wireless remote control to allow quick, one person positioning of
the antenna while monitoring the signal meter screen on your TV. The VuQube is compatible
with standard digital programming services from DIRECTV®, DISH Network™, Bell ExpressVu™
and free-to-air receivers.
This manual includes:
• Components overview
• Operating instructions
• Elevation quick reference maps
The Satellite Broadcast Market is changing and expanding. The information in this manual was accurate at the time of
printing. If the Vu Qube does not operate as shown in this manual, please call 1-800-982-9920 Ext. 412.
Technical Support:
1-800-982-9920 Ext. 412
Notes:

4Vu Qube
5
Vu Qube
Vu Qube V1000 Component Overview
Operating Manual (P/N 10153-2) Vu Qube Antenna (P/N VQV10P)
Vu Qube Remote (P/N VQV10PR) RG6 Coaxial Cable (50’) (P/N 10140-1)
Additional Items needed to watch TV
• Satellite TV service
• Satellite TV receiver
• Television
Specifications
Height: 17.5”
Width: 16”
Weight: 10.5 lbs
Range: US/Southern Canada
Compatibility: DIRECTV®, DISH Network™, Bell ExpressVu™and Free-to-air receivers
FCC User Information
Main Components:
Vu Qube Antenna
Model #: VQV10P
FCC ID: UUM10156V10
IC: 6873A -10156V10
Please note that changes or modifications to the Vu Qube or Vu Qube remote not
expressly approved by Vu Qube could void the purchaser’s or user’s authority to operate
this equipment.
This device must not be co-located with other transmitters to ensure compliance with
FCC RF exposure requirements.
The Vu Qube and Vu Qube remote have been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
1. Display
2. Elevation Buttons
3. Rotate buttons
4. Satellite position memory
5. Power
1. Vu Qube Enclosure
2. Handle
3. Coaxial cable Connector
1
2
3
1
2
3
4
5
Vu Qube Remote
Model #: VQV10RP
FCC ID: UUM10157V10
IC: 6873A -10157V10
This devise complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1) This devise must not cause harmful interference, and
2) This devise must accept interference received including
interference that may cause undesired operation.
This devise complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1) This devise must not cause harmful interference, and
2) This devise must accept interference received including
interference that may cause undesired operation.

6Vu Qube
7
Vu Qube
Position and Connect
Setting up
1. Position Vu Qube outside with clear view of southern sky.
• To speed up search time, point side opposite handle south
2. Connect Coaxial cable to Vu Qube and to Satellite receiver.
•Hand tighten (DO NOT use a wrench)
•Make sure to connect coaxial cable to “Satellite In” port on satellite receiver
Tilt and Turn Vu Qube Antenna with wireless remote
Aligning Vu Qube Antenna to Satellite
1. Set Vu Qube Antenna to correct Elevation using Up/Down Arrows.
•Elevation can quickly be determined using Maps in the back of this manual or by entering
zip-code in satellite receiver prior to navigating to signal meter screen.
2. Following the instructions in your satellite receiver owners manual, navigate to the
satellite signal meter screen and select the appropriate transponder as follows:
DISH Network 11
DIRECTV 19
3. Rotate Vu Qube Antenna with Left/Right arrows until signal appears on Signal Meter.
4. Maximize Signal Strength by slightly adjusting Vu Qube Antenna using all 4 arrows.
Tune In
Watching TV
Once you have a satellite signal follow satellite receiver on-screen guide to navigate
to programming.
NOTE: it may take a few minutes to download programming from the satellite
Satellite Position Memory
TO STORE POSITION:
Hold down either the Satellite 1 or Satellite 2 button for at least 2.5 seconds.
The LCD will show “P1” or “P2” when button is released.
TO RECALL POSITION:
Momentarily press the desired satellite recall button (Satellite 1 or Satellite 2) for no more than
1 second. The LCD will show the recalled satellite location “r1” or “r2”.
TO CANCEL RECALL:
Press any arrow button to stop moving to a stored position.
Point side opposite handle south
to speed up search
N
S
WE
SATELLITE IN
connection
Indicates direction antenna is pointing
(see above)
Indicates elevation
Gap in circle indicates position
of coaxial connector / handle
Line flashes and moves to
indicate rotating antenna

8Vu Qube
9
Vu Qube
Troubleshooting
If you cannot lock-on to the correct satellite, it is most likely that an object is blocking the signal.
If this is the case, move the Vu Qube to have an unobstructed view of the southern sky.
ERROR CODES Problem Action
Care & Maintenance
The Vu Qube has been designed to be maintenance and trouble free. For optimum signal strength,
keep the cover clean from dirt, bugs, and other debris. Periodic washing of the top cover with mild
soap and water is recommended. DO NOT USE SOLVENTS TO CLEAN VU QUBE. DO NOT DROP OR
EXPOSE TO JARRING MOVEMENTS.
If you have any comments or questions, please call 1-800-982-9920 Ext. 412.
Limited Warranty
Every Vu Qube is thoroughly inspected and tested before leaving the factory and is covered by a one year limited warranty
against any defects in material or workmanship after the date of original purchase. For one year from the date of purchase,
at the option of Vu Qube, the unit and/or components will be repaired or replaced with a new, repaired, refurbished or
comparable product if the unit becomes defective. This limited warranty does not cover replacements or repair for damage,
malfunction or inoperability caused by abuse, misuse, accidents, or causes not within the control of Vu Qube.
Only authorized Vu Qube technicians can perform repair. Removing cover and any unauthorized repair will void warranty.
Should any trouble develop during the warranty period, contact Vu Qube at 1-800-982-9920 Ext. 412.
DO NOT RETURN TO STORE. Any product return should be sent to: Electronic Controlled Systems
11200 Hampshire Ave S.
Bloomington, MN 55438
ELEVATION REFERENCE MAPS
EO
E1
E2
Remote is unable to send
commands to antenna
Remote is unable to
receive response from
antenna
Miscommunication
between remote and
antenna
• Make sure RECEIVER is turned ON
• Make sure coaxial cable from
Vu Qube is attached to receiver
• Move remote closer to Vu Qube
Move remote closer to antenna
Call 1-800-982-9920 Ext. 412
If the above does not fix the EO problem, remove power from both
Vu Qube and remote for 1 minute. This can be done by disconnect-
ing the coax from the Vu Qube (or unplugging satellite receiver
from power) and removing the batteries from the remote. After
one minute, reconnect and re-power all components.
101º W - DIRECTV®

10 Vu Qube
11
Vu Qube
119º W - Dish Network® 110º W - Dish Network®