Wali CM2665XL User manual

INSTALLATION MANUAL
[email protected]

2

Supplied Parts List
3
Spacer
M-C(x4)
Ceiling Mount Pole
A(x1)
Extension Pole
B(x1)
Extension Pole
C(x2)
Monitor Mount Pole
D(x1)
VESA Plate
E(x1)
M8x60 Bolt
F(x6)
M8x55 Bolt
G(x2)
Nut
H(x8)
Wrench
I(x1)
Allen Key
J(x1)
Marking Center Finder
K(x1)
M4x14 Bolt
M-A(x4)
M5x14 Bolt
M-B(x4)
M6x14 Bolt
M-C(x4)
M8x20 Bolt
M-D(x4)
D5 Washer
M-E(x4)
D8 Washer
M-F(x4）
Spacer
M-G(x8)
Bolt
W-A(x4)
Concrete Anchor
W-B(x4)
Washer
W-C(x4)
Adapter
K(x4)
Bolt
L(x4)
Nut
M(x4)
M6x30 Bolt
M-A(x4)
M8x30 Bolt
M-B(x4)

4
Step 1
Option A
If you install this product on wood stud wall, mark the position with provided Marking Center Finder Kand pencil
on the wall.Drill 3/16"(4.5mm) diameter x 2.2"(55mm) length hole at the marked position, attach the Ceiling Mount
Pole Ato wall and tighten using 4pcs Bolt W-A & Washer W-C with provided Wrench I. Use both Allen Key J
and Wrench Ito tighten for stability after pole angle adjusting finished.
Wood Joist Ceiling
K
A
J
I
W-A
W-C

5
Step 1
Option B Concrete Ceiling
J
I
K
W-B
If you install this product on concrete wall,mark the position with provided Marking Center Finder Kand pencil on
the wall.Drill 1/2"(12mm) diameter x 1.8"(45mm) length hole at the marked position,attach the Ceiling Mount Pole
Ato wall and tighten using 4pcs Concrete Anchor W-B with provided Wrench I. Use both Allen Key Jand
Wrench Ito tighten for stability after pole angle adjusting finished.

6
Step 2
Guide the cable through the opening cable slot on Ceiling Mount Pole A, attach the Extension Pole B,2 pcs
Extension Pole Cand Extension Pole Done by one and tighten using 6pcs M8x60 Bolt F& Nut Hon the top
three joint connection with provided Allen Key Jand Wrench Ias image shown, tighten the bottom joint
connection using 2pcs M8x55 Bolt G& Nut H.
A
C
C
B
D
H (X6）
H (X2）
F (X6）
G (X2）
min493mm~max1496mm

7
Step 3
Step 3.1
Step 3.2a
Select M4x14 Bolt M-A or M5x14 Bolt M-B according to your TV/Monitor,bolt VESA Plate Etogether
with D5 Washer M-E into the mouting holes on the back of TV/Monitor, tighten with screwdriver; If select
M6x14 Bolt M-C or M8x20 Bolt M-D according to your TV/Monitor, bolt VESA Plate Etogether with D8
Washer M-F into the mounting holes on the back of TV/Monitor, tighten with screwdriver.
(Screwdriver needed but not included)
E
W-C/W-D
W-A/W-B
M-E
M-F

8
Step 3
Step 3.2b
Step 3.2c
Bolt VESA Plate Eusing M8x20 Bolt M-D , D8 Washer M-F together with Spacer M-G into the
mounting holes on the back of TV/Monitor with screwdriver to tighten.
(Screwdriver needed but not included)
M-F
M-D
M-F
M-D
M-G
M-G
E
M-G
Bolt Adapter Konto the VESA Plate Eusing Bolt Land Nut Mwith provided Wrench Ior
screwdriver to tighten. (Screwdriver not included)
E
K
L
M

9
Step 3
Step 4
Twist counterclockwise to take off the bottom nut on the VESA Plate Eand twist counterclockwise to
loosen the top 2 nut.
Step 3.2c
Four bolt methods available for multiple TV/Monitor specification.
1) Bolt M6x30 Bolt M-A or M8x30 Bolt M-B together with D8 Washer M-F ,Spacer M-G ,Spacer M-C
with screwdriver to tighten;
2) Bolt M6x30 Bolt M-A or M8x30 Bolt M-B together with D8 Washer M-F ,Spacer M-C with screwdriver to tighten;
3) Bolt M6x30 Bolt M-A or M8x30 Bolt M-B or M8x20 Bolt M-D together with D8 Washer M-F , 2 pcs Spacer M-G
with screwdriver to tighten;
4) Bolt M6x30 Bolt M-A or M8x30 Bolt M-B or M8x20 Bolt M-D together with D8 Washer M-F , Spacer M-G with
screwdriver to tighten.
(Screwdriver needed but not included)
M-G
M-G
M-G
M-C
M-C
M-F
M-F
M-F
M-F
M-A
M-B
M-A
M-B
M-A
M-B
M-D
M-A
M-B
M-D
E

10
Step 5
Hang the assembled TV/Monitor onto the assembled Monitor Mount Pole D, twist clockwise to tighten
the three nuts on the VESA Plate Efor stability as image shown.
E
D