Wali GSDM001S User manual
INSTALLATION MANUAL
75x75/100x100 32"
MAX 1 9kg
(2. 2~19.8lbs )
R AT E D
~
GSDM001S
Monitor Desk Mount
2
Supplied Parts List
3
Arm
A(x1)
Pole
B(x1)
Base
C(x1)
VESA Plate
E(x1)
Support Plate
J(x1)
C-Clamp Brace
F(x1)
C-Clamp
G(x1)
Décor Cover
H(x1)
Bolt
I(x1)
Clip Holder
D(x1)
Allen Key 4mm
O(x1)
Support Plate
K(x1)
Washer
L(x1)
Nut
M(x1)
Anti-skid Pad
N(x4)
M6x16 Bolt
T(x3)
Allen Key 6mm
P(x1)
Wrench
Q(x1)
M6x10 Bolt
R(x2)
M6x12 Bolt
S(x3)
M4x12 Bolt
M-A(x4)
M4x16 Bolt
M-B(x4)
M5x12 Bolt
M-C(x4)
M5x16 Bolt
M-D(x4)
D5 Washer
M-E(x4)
Spacer
M-F(x4)
4
Step 1
Step 2
1. Place the Pole Bonto the top hole of Base C,connect Pole B and Base Cfrom the bottom using M6x16 Bolt T
and tighten with Allen Key 4mm O; Connect C-Clamp Brace Fto Base Cfrom the bottom using M6x12 Bolt Sand
tighten with Allen Key 4mm O.Tear off the protect paper to attach Anti-Skid Pad Nto the bottom designated
position of Base Cas image shown.
Fit clamp: 0.39”-3.3”
Grommet: 0.39”-3.1”
Option A Clamp Installation
N
F
S
O
B
C
O
O
O
T
B
C
F
N
S
5
Step 2
O
R
G
1.97"-3.3"
0.39"-2.17"
H
Option A
Clamp Installation
3. Put on the Décor Cover Hto cover the C-Clamp Brace F, rotate the knob clockwise to fasten for stability.
or
R
O
H
F
F
G
2. Select the preferred height firstly and connect C-Clamp Gto C-Clamp Brace Fusing M6x10 Bolt Rand tighten with
Allen Key 4mm O.
6
Step 2
Option B
Grommet Base Installation
1. Guide Support Plate J through Bolt Iand connect them to Base Cfrom the bottom using M6x12 Bolt Sand
tighten with Allen Key 4mm O. Tear off the protect paper to attach Anti-Skid Pad Nto the bottom designated
position of Base Cas image shown.
Q
K
L
M
0.39”-3.1”
S
I
J
O
N
Q
K
L
M
C
J
S
O
I
I
N
If the existing grommet hole comes with a plastic protector,remove it to ensure a flat surface before installing the desk
mount. Insert the assembled Pole through the desk hole, guide the Support Plate K,Washer Land Nut Mthrough the
Bolt I, rotate the Nut Mclockwise to fasten for stability.
2a Existing Grommet Hole Installation
7
Step 2
Step 3
Q
K
L
M
0.39”-3.1”
D
A
K
A
D
B
P
L
M
Q
Option B
Grommet Base Installation
Mark the position of the hole on your mounting surface.Drill a 3/8"(10mm) diameter hole at the marked position through
the mounting surface.Insert the assembled Pole through the desk hole, guide the Support Plate K,Washer Land
Nut Mthrough the Bolt I, rotate the Nut Mclockwise to fasten for stability.
2b Self-drilled Grommet Hole Installation
ø 10mm
(ø ") 3/8
Put the Clip Holder Dand Arm Athrough the Pole B, adjust the preferred height and tighten using Allen Key 6mm P.
I
Grommet Base Installation
8
Step 4
Step 4.3a Step 4.3b
Select M4x12 Bolt M-A or M5x12 Bolt M-C
according to your TV/Monitor,connect VESA Plate E
together with D5 Washer M-E into the mounting
holes on the back of TV/Monitor, tighten with
screwdriver.(Screwdriver needed but not included)
Select M4x16 Bolt M-B or M5x16 Bolt M-D
according to your TV/Monitor,connect VESA Plate E
together with D5 Washer M-E and Spacer M-F into
the mounting holes on the back of TV/Monitor,
tighten with screwdriver.(Screwdriver needed but not
included)
Step 4.1
Select TV Screws
Step 4.2
Select Spacers ( if needed )
E
E
M-E
M-E
M-C
M-A
E
M-E
M-F
M-B
M-D
E
Hand thread screws
into the threaded
inserts on the back of
your TV to determine
which screw diameter
(M4 or M5) to use.
M4 M5
9
Step 5
Step 6
A
Pull the buckle and put the assembled TV/Monitor onto the Arm Aand ensure the stability.
Press the Arm Aon horizontal level as image shown, adjust gas spring tension to your personal preference using Allen
Key 6mm P, adjust the tilt tension using Allen Key 6mm P.
P
P
For Heavier Monitors
For Lighter Monitors
A
P
P
12
10
Step 7
Step 8
Pull the bottom cable slot cover to the VESA direction to detach it off the arm, open the four corner button of the top cable
slot cover to detach it off.
Guide the cable through the cable slot and put the cover back to arm.
11
Step 9
P
O
±90°
+90°
-90°
±90°
Manually swivel,tilt or rotate the angle for the best operating environment; Store the Allen Key 4mm Oand Allen
Key 6mm Pin the holder of Décor Cover Hfor future convenience.
P
O
H
If you have any questions,please contact us.
We support the technology that brings your home to life.
We offer high quality products, professional customer service,
and extensive technical support.
Other Wali TV Mount manuals
