WANHAO DUPLICATOR 9 User manual

DUPLICATOR 9
GETTING
Thanks for choosing Wanhao 3D Printer products. You’re just moments away from printing your rst 3D
model. It’s important that you follow these steps carefully to ensure correct setup of your 3D Printer.
STARTED
GUIDE
You can also visit www.wanhao3dprinter.com/Video/D9 video/wanhao D9 unboxing
for step by step guide on unboxing and setup, levelling, lament installation and printing.
Package Contents:
1 x WANHAO 3D Printer
1 x Filament Spool Holder
1 x Filament Spool Stand
1 x Power Cable
1 x USB Cable
1 x 8GB SD Card
1 x Hex Screw Driver
1 x Hex Key Set
6 x Hex Bolts
2 x Plastic belts
1 x 1.75mm PLA Filament
1 x Needle for unclugging nozzle
ASSEMBLING AND MOUNTING
1Take out all components
from the box and
place them on the at
ground.
1-Base
2-Z axis Tower Pillar*2
3-X axis rail
4-X axis gantry
5-MK12 Extruder
Place the Base on
it’s side. Find the Z
axis pillar with sticker
No.2. Slide the No.2
pillar into the base
vertical locker. Then
tighten the bolt at
bottom of base.
2
AD
4 5
6
Insert the leveling
card or an A4 paper
between the nozzle
and bed. Adjusting
the Z axis height,
until you can feel the
friction while moving
the card or paper.
Click the upper Z to move
extruder up and click the
lower Z to move extruder
down. Stop clicking until
you feel the leveling card
getting friction while
moving the card.
Click NEXT to initiate
auto leveling.
7
Congratulation! You have nished bed leveling. For video installation,
please scan the QR code.
Video Installation Ofcial Website Wanhao Store
To move the extruder
by hand to 4 corners
separately. Adjusting
the knob at each
corner, until you feel
friction while moving
the leveling card.

CONSTRUCT AND CONNECT [CONT.]
3Tighten the locking
bolt clockwise. Then
install the other Z
axis pillar onto the
Base.
Loose the two locking
bolt on No.3 and No.4
Z axis pillar by around
5mm. So there will be
sufcient space for X axis
pillar to slide in.
4
5Slide the X axis pillar into
the No.3 and No.4 bolts. If
there’s not enough space,
you may need to re-loose
the locking bolt.
To tighten the locking
bolt through the hole on
top of the X axis pillar.
Lock both No.3 and No.4
pillar.
6
7Insert the plastic cover
onto the two ends of X
axis pillar.
Note: Please double
check the Z axis and X
axis pillars. If any bolt
not secured. You need
to secure the screws to
ensure the gantry are
steady and tight.
Rotate the cylinder holder
for a bit but not too close.
Tight enough that can not
slide into pillar freely.
This is also same to the
other side with stickers
No.6.
8
9Mount the X axis rail.
Align the right and left
side holders rst. Please
make sure the rail is
located in the middle
of the X axis. You may
need to adjust the
distance to both ends
through the cylinder
holders.
Then tighten the bolts
on both end of No.5 and
No.6.
10
11 Mount the MK12
extruder onto the
X axis holder. Make
sure the locking holes
match to the holder
holes.
A total of 4 bolts need
to be tightened, but the
rst bolt should not be
too tight until the other
three bolts are mounted,
then tighen all the bolts
together.
12
WIRING INSTRUCTION
B C
LEVELING BEFORE PRINTING
2
1Turn the couple to lower the
two Z axis in order to level
the two Z axis at same height.
Note: The ruler or height
gauge would provide more
accurate height for both two
Z axis. The two axis need to
be at same height.
3
Turn on the printer.
Release the 4 bed
leveling nuts by 4-5
turns. Then Click LEVEL.
Read the instruction, then
click NEXT.

CONSTRUCT AND CONNECT [CONT.]
3Tighten the locking
bolt clockwise. Then
install the other Z
axis pillar onto the
Base.
Loose the two locking
bolt on No.3 and No.4
Z axis pillar by around
5mm. So there will be
sufcient space for X axis
pillar to slide in.
4
5Slide the X axis pillar into
the No.3 and No.4 bolts. If
there’s not enough space,
you may need to re-loose
the locking bolt.
To tighten the locking
bolt through the hole on
top of the X axis pillar.
Lock both No.3 and No.4
pillar.
6
7Insert the plastic cover
onto the two ends of X
axis pillar.
Note: Please double
check the Z axis and X
axis pillars. If any bolt
not secured. You need
to secure the screws to
ensure the gantry are
steady and tight.
Rotate the cylinder holder
for a bit but not too close.
Tight enough that can not
slide into pillar freely.
This is also same to the
other side with stickers
No.6.
8
9Mount the X axis rail.
Align the right and left
side holders rst. Please
make sure the rail is
located in the middle
of the X axis. You may
need to adjust the
distance to both ends
through the cylinder
holders.
Then tighten the bolts
on both end of No.5 and
No.6.
10
11 Mount the MK12
extruder onto the
X axis holder. Make
sure the locking holes
match to the holder
holes.
A total of 4 bolts need
to be tightened, but the
rst bolt should not be
too tight until the other
three bolts are mounted,
then tighen all the bolts
together.
12
WIRING INSTRUCTION
B C
LEVELING BEFORE PRINTING
2
1Turn the couple to lower the
two Z axis in order to level
the two Z axis at same height.
Note: The ruler or height
gauge would provide more
accurate height for both two
Z axis. The two axis need to
be at same height.
3
Turn on the printer.
Release the 4 bed
leveling nuts by 4-5
turns. Then Click LEVEL.
Read the instruction, then
click NEXT.

DUPLICATOR 9
GETTING
Thanks for choosing Wanhao 3D Printer products. You’re just moments away from printing your rst 3D
model. It’s important that you follow these steps carefully to ensure correct setup of your 3D Printer.
STARTED
GUIDE
You can also visit www.wanhao3dprinter.com/Video/D9 video/wanhao D9 unboxing
for step by step guide on unboxing and setup, levelling, lament installation and printing.
Package Contents:
1 x WANHAO 3D Printer
1 x Filament Spool Holder
1 x Filament Spool Stand
1 x Power Cable
1 x USB Cable
1 x 8GB SD Card
1 x Hex Screw Driver
1 x Hex Key Set
6 x Hex Bolts
2 x Plastic belts
1 x 1.75mm PLA Filament
1 x Needle for unclugging nozzle
ASSEMBLING AND MOUNTING
1Take out all components
from the box and
place them on the at
ground.
1-Base
2-Z axis Tower Pillar*2
3-X axis rail
4-X axis gantry
5-MK12 Extruder
Place the Base on
it’s side. Find the Z
axis pillar with sticker
No.2. Slide the No.2
pillar into the base
vertical locker. Then
tighten the bolt at
bottom of base.
2
AD
4 5
6
Insert the leveling
card or an A4 paper
between the nozzle
and bed. Adjusting
the Z axis height,
until you can feel the
friction while moving
the card or paper.
Click the upper Z to move
extruder up and click the
lower Z to move extruder
down. Stop clicking until
you feel the leveling card
getting friction while
moving the card.
Click NEXT to initiate
auto leveling.
7
Congratulation! You have nished bed leveling. For video installation,
please scan the QR code.
Video Installation Ofcial Website Wanhao Store
To move the extruder
by hand to 4 corners
separately. Adjusting
the knob at each
corner, until you feel
friction while moving
the leveling card.