WANHAO Duplicator 5S User manual

Tel: [phone]
Email: [email protected]
Web: WWW.WANHAO3DPRINTER.COM
USER MANUEL
Resolution 0.02mm
Speed 300mm/second
Software: Wanhao Maker
3D
ＷＡＮＨＡＯ ＰＲＩＮＴＥＲ
Duplicator5S

Duplicator 5S

WANHAO is excited to welcome you to the world of the WANHAO Duplicator 5S. .Following this guide will help
with Duplicator 5S
This User manual is designed to help you start your experience with Duplicator 5S. .Within these pages, we want
to show you how simple and easy it is to produce great prints.You might be familiar with earlier types of Wanhao
printers or other 3D-printers. It is essential that your read this manual carefully as there are a lot of new procedures
ensure that you are getting the most out of your machine, and that you continue to make amazing things,
.
Ａ１ Ｔｈｅ Ｄｕｐｌｉｃａｔｏｒ ５Ｓ Ｅｘｐｅｒｉｅｎｃｅ

28kg(62lbs)
39kg(86lbs)
Width 565mm
Length 605mm
Height 950mm
295*195*575mm
Height 810mm
Width 415mm
Length 455mm
Data
Print Technology Fused lament
Fabrication(FFF)
Build Volume
Layer Resolution Ultra high 20 micron
High 60 micron
Medium 100 micron
Low 200 micron
Position precision X 12.5 micron
Y 12.5 micron
Z 5 micron
Filament diameter 3MM +-0.15mm
Nozzle diameter 0.4 mm
Print speed 30mm/s-300mm/s
Travel speed 30mm/s-350mm/s
Software
Software Package Wanhao Maker
File Type STL
Support Windows(XP32 bit/7+)
Mac OS X( 10.6 64bit +)
Electrical
AC Input 100-240V
4 AMPS
 50-60Hz
200Watt max
Power Requirements 24V [email protected]
Connectivity Stand-alone printing
from SD-card
USB（rmware)
Physical dimensions
Frame Dimension
Shipping box
Net Weight
Gross Weight
Temperature
Ambient Operating
Temperature 10°- 38°C
Storage Temperatuer 0° - 40°C
Operating Nozzle
Temperature 180°- 260°C
Sound
Average Operational
noise 48dBA.
WARNING: The Duplicator 5 generates high temperatures and has hot moving parts that can cause injury.
Never reach inside of the Duplicator 5 while it is in operation. Always control the Duplicator 5 from the push
wheel on the front or with the power-switch on the back. Allow the Duplicator 5 to cool down for 5 minutes
before reaching inside.
CAUTION: When opening the Duplicator 5 for service, ensure that the power supply is turned off and the
cord is disconnected from the wall socket.
CAUTION: Only use power supply provided with your Duplicator 5 .
Ａ２ Ｓｐｅｃｉｆｉｃａｔｉｏｎ ｏｆ ｔｈｅ Ｄｕｐｌｉｃａｔｏｒ ５Ｓ

Ｂ１ Ｕｎｂｏｘｉｎｇ
1. Place The Duplicator 5S box on
the ground next to a clean, flat
workspace.
2. Cut of the rope and Discard the top
cardboard insert.
3. now remove the inner cardboard
box, and take the Duplicator 5S out
of its box.
4. Now you can clear away the cardboard
inserts and remove the Accessory Box
from The Duplicator 5S.

accesoires that comes with this 3D printer.All the following parts should be in the box,please
Besides your Duplicator 5S supplied with SD card in the 3D printer ,there are a lot of essential
Ｂ２ Ｗｈａｔ＇ｓ ｉｎ ｔｈｅ ｂｏｘ
check contents.
1 pc printer 1 pc bulid plate 1 pc spool holder 1 pc clamp
1 pc USB cable 1 pc Print raiser 1 pc Print wrench 1 pc SD card reader
1 pc Power supply unit 1 pc SD card 1 pc 3mm filament

1. LED display
2. Push and Rotate button
3. Extruder Cable
4. Filament tube
5. MK10 Extruder
6. Building Plate
7. Building Plate Screw
8. Spool Holder
9. USB Socket
10. Power Switch
11. Material Feeder
12. Power Socket
Ｂ３ Ｄｕｐｌｉｃａｔｏｒ ５Ｓ ｇｌａｎｃｅ

7 . The main cable in the power brick can be
6 . The plug has a sliding collar. When
5 . Next take the power plug out of the wall
slot.The flat side of the power plug
S B
switch and U
has to face towards the top of the Duplicator5 .
step is to make sure the Duplicator5 turned off. This
the Duplicator5 , in the round hole next to the on/off
Now the next step is to give the Duplicator 5 power
.
This is done by attaching the external power supply.
Detaching the power supply
1. If the power supply has to be detached, the first
is done by pressing the power switch to 0.
First make sure the power switch is in the OFF
position, this is when the button at the back is
pressed to [0].
2. The corresponding power cable (for your country)
has to be inserted in the power brick of the power
supply.
3. The connector has to be inserted at the back of
4. Now plug the external power supply into the wall
socket.
socket.
removing the plug from the machine, gently
slide the collar outwards which will release
the plug and allow it to come out with ease.
CAUTION: Please make sure not to pull
the cable. Excessive force may result in
breaking this component.
detached by pulling it out gently.
Ｃ１ Ｉｎｓｔａｌｌ Ｐｏｗｅｒ Ｓｕｐｐｌｙ
S
S
S
S

auto- homing f inshed
4. Prepare a name card, Wait until
1. Navigate the Rotate button and
Push the button 2. Navigate the Rotate button to Utility and Push the button
7. Navigate to Step2, 3 and 4
6. Insert one name card between
the nozzle and plate(0.1mm thick)
5. Push the button and adjust nut
below the plate
3. Navigate to Calibrate plate and
push the button
8. Adjust the rest 2 nuts and ensure
name card can go through
Ｃ２ Ｈｏｗ ｔｏ ｌｅｖｅｌ ｔｈｅ ｂｕｌｉｎｇ ｐｌａｔｅ

guided along the filament guide,with the filament
1. Now that we have completed the initial leveling
tasks we [CONTINUE] and go to the step where
we are going to insert filament material in the
material feeder.
Navigate the control button to ---Utility---Load
2. Wait the extruder to heat up to 220'C. Warning,
never touch the nozzle while printer power on.
You are only allowed to touch the nozzle when
the printer is power off.
3. Please make sure you have a filament spool
positioned over the spool holder,
in counter clockwise direction.
4. This step needs some extra focus.
The wheel in the material feeder will start rotating
slowly. Take the material and put it in the hole at
the bottom of the material feeder. There is a hole
where it should go into right above the sticker.
Follow the display instruction with the supporting
images below but WAIT! before pushing and
check the next page for more instructions.
Ｃ３ Ｌｏａｄｉｎｇ ｆｉｌａｍｅｎｔ ｍａｔｅｒｉａｌ

Installation wiz ard will continue to finish the
printer and ready to become your physical object.
your model at the background. Faster than ever.From there it is just seconds away from your
object, Wanhao Maker’s slicer engine prepares
program that helps you install the lastest firmware as well as to calibrate your printer.While you
printing.It is fully preconfiguresed to work on every Duplicator5 S.Wanhao comes with a easy setup
as affordable and easy as possible.It contains most function you need to prepare a 3D file for
How to Install Wanhao Maker
Wanhao Maker software prepares your 3D model into Machine language which required to make
3D object. Wanhao Maker is developed by Wanhao International Team aimed to make 3D printing
make decisions on the look and quality of your 3D
1. Down load Wanhao Maker or copy software
from SD card. Double click the Wanhao Maker.
EXE to install softwar
2. Language selection. We provide 3 language
at present, English, Simplify Chinese, Chinese
3. Folder route. Please take default route for
faster slicing speed.
rest steps.
How to Install Wanhao Maker
4.

Wanhao Maker Interface
1. Load le
Click this button to load an object to
your print area. You can add as many
objects as you can t on the plate.
2. Start Making
Press this button to start Slicing. There
will be more options after pressing the
button
3. Save toolpath (SD)
When you press this button the
prepared toolpath will be saved on the
SD card.
4. Load le
Click this button to load an object to
your print area. You can add as many
objects as you can t on the plate.
5. Delete
Click on any item then delete an object
from the plate.
6. View
Check the object from different angle.
7. Pan
To Move the plate from all directions, so
you can check more clear.
8. Move
Move the object left, right, front and
back wards.
9. Rotate
Move the object with different angle. X,
Y, Z axis can be with suitable angle for
printing.
10. Scale
To enlarge to shrink the object
11. Mirror X
Options to mirror the object from X axis
12. Mirror Y
Options to mirror the object from Y axis
13. Mirror Z
Options to mirror the object from Y axis
14. Duplicate
To duplicate the object in same size.
15. Reset
Let the object back to start position
16. Start Making
Press this button to start Slicing. There
will be more options after pressing the
button
18. Build plate
This is the plate your object to be
printed
Wanhao Maker Interface

that your file has been saved.
7. .When finished saving it will give you the notification
* .i file into SD card directly.
range of the printing table.
3.After you put the file in,please check if it is in the
the file on the SD card.Or you can copy the toothpath
use your own STL file.
Preparing a 3D model
1. Most 3D printable files that you will find on www.
thingshares.com are in the STL format. Or you can
2. When you have loaded a STL file into Maker . By
clicking Making, you might notice the progress bar.
4. When the 3D model is prepared, the Save toolpath
button shows up and gives you the option to save the
prepared model in a directory.
Finish page, Maker gives you an
indication about your print on
- Estimated Print Time
-Amount of material required
-And the weight of your 3D print
5. After you inserted the included SD-card into your
computer, Maker changes the Save toolpath Button
into the Toolpath to SD Button.
6. Just after you choose for the Toolpath to SD button
you will see the same progress bar but now it saves
8. Before taking out the SD-card make sure you
always choose the safely eject.
9. Then insert the SD card into the printer socket.
Navigate to Print from SD card to print.