Warmtec HT200 User manual

HT200
INFRARED HEATER
Manual

1. CAUTION REGARDING THE SECURITY
1
Instructions should be carefully read before installation and retained
by the user. The booklet must be keeped and delivered to the new
user in case of cession of the machine. The Manufacturer reserves
the right to vary the features of the product without prior notice. The
technical data are merely indicative.
1. This appliance is intended solely for the use it has been designed
for, namely room and people heating. The Manufacturer is not
responsible for any damage that could happen for improper use.
2. After unpacking make sure that the appliance is complete and
shows no signs of visible damage or tampering.
3. Keep packing materials, which are potential dangers, away from
children.
4. The device can be used by children at least 8 years (as well as by
persons with reduced physical, sensory or mental capabilities, or
lack of experience or required knowledge) provided that they are
under surveillance, or after they have been instructed relating to
the safe use and have understood the potential dangers. Children
should not play with the appliance. Cleaning and maintenance
must be performed by the user and not by unsupervised children.
5. Children of less than 3 years should be kept away unless continu-
ously supervised.
6. Children aged from 3 years and less than 8 years shall only switch
on/off the appliance provided that it has been placed or installed
in its intended normal operating position and they have been giv-
en supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
7. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
8. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
EN USE AND MAINTENANCE

9.
2
Children should be supervised to ensure that they do not play
with the appliance.
10. This heating appliance does not feature a device to control ambi-
ent temperature. Do not use it in small rooms used by people
who are unable to leave such rooms on their own unless they are
under constant surveillance.
11. Before inserting the plug make sure that the voltage is the same
as indicated on the device.
12. Do not use in presence of gas, inflammable or explosive liquids
or substances.
13. Some fundamental rules which apply to all electrical devices
must be observed when using the heater:
• Do not touch the heather with wet hands.
• Do not handle with bare feet.
• Do not pull the electric cord or the device itself to unplug it
from the socket; pull the plug directly.
14. Avoid the use of an extension cord with this product, because
the extension cord may overheat and cause a risk of fire.
15. Do not apply any modification to the product that could compro-
mise the safety.
16. Keep connections dry.
17. If the appliance is not used for a long period, disconnect it from
the power supply.
18. Always disconnect the appliance before doing any maintenance
operation.
Some parts of the appliance may become hot and cause burns. Cau -
tion should be exercised if there are children and vulnerable people.
2. CAUTION REGARDING THE INSTALLATION OF THE APPLIANCE
Installation should always be carried out by a qualified electrician or a
competent person in accordance with the standards HD 384 CENEL -
EC for Europe, or international IEC 60346-7-708 1988, and the stand -
ard AS/NZS 3000 (Australian wiring rules). The energy supply must
be done through a properly grounded socket. The appliance must be
connected to the power supply by a H05RN-F cable, gotten properly
into dimension in respect to its own length and the kind of the con-
nection (see the Table 1).

3
An overvoltage category III Combined Circuit breaker and Re-
sidual Current Device (RCD) with rated earth leakage operation
not exceeding 30mA must be fitted upstream on the supply
line. The circuit breaker must have a contact opening distance
of at least 3 mm.
Model HT200
Power supply
220-240V ~ 50–60Hz
Total power
2000 W
Current
9 A
Cable H05RN-F (min.section) 3 x 1.5 mm²
(*) Cable minimum section - per 5 m length. Table 1
The HT200 infrared heater are intended for indoor use only and must
be kept away from moisture and dust.
Keep the indicated distances between the heater and the wall/ceil-
ing (fig. 1-2-3).
• Install the heater in such a way that the lamps stay horizontally.
• A safety distance of not less than 1 m should always be left in front
of the heater.
• The appliance must not be located neither directly below, nor in
front of a socket-outlet.
• Do not use the heater directly near a bathtub, a shower, a swim-
ming pool.
• Ensure that the power cable cannot come into contact with the re-
flector of the appliance and does not intrude into the area of light flux.
• Ensure that there is no possibility of inflammable material, combus -
tible material or curtains coming into contact with the Heater, or lie
near the heater.
Wall mounting using the braket (provided)
Make sure that the wall where you plan to mount the appli-
ance is solid, and free of electrical cables or water pipes in-
side.

4
This heater is intended for permanent installation. Be sure
that the heater is not facing the ceiling or inflammable sub-
stances.
Fasten the bracket to the wall by means of 2 dowels at least, passing
through the A holes (fig. 1). Use the B holes just as reference (fig. 1).
The heater can be angled on its bracket in correspondence to the C
screw, and the modules can be pointed in correspondence to the D
couplings (fig. 2 ). When the adjustment has been made, tighten all
the screws.
Ceiling mounting with chains (not provided)
Fasten the chains (having an appropriate length) to the ceiling, and
hook them to the heater in corrispondence of all the four E holes by
means of the “S” shaped rings enclosed inside the packaging.
3. TECHNICAL FEATURES
Model HT200
Power supply
220-240 V ~ 50-60 Hz
Power
1 x 2000 W
Lamps
1
Range
9-12 m²
Weight
2.2 kg
Table 2
4. USE INSTRUCTIONS
The Industrial infrared heater was designed for zone heating on large
premises. Production departments, churches, gymnasiums are ide-
ally application sites. With high efficiency on heating from long dis-
tance, a compact size and a light weight a wide range on insta-lla
tion can be easy made. The comfort is immediate, no preheating is
necessary and this can give a large cost saving on wide air volume

5
or where there is discontinuous presence. The radiant heating give a
pleasant comfort and the absolute silence is assured without moving
parts. Without air movements there isn’t the spreading of particles
or dust.
• Switch on the heater simply by connecting to the power supply.
• Do not touch the metallic parts when the heater is working.
• Ensure that the rays of the heater are directed towards the area it
is wished to heat. If necessary, change the angle of inclination by
loosening the screws of the support or the modules.
• In unoccupied premises it is recommended that the heating sys-
tem is switched off by disconnecting from the electrical supply.
Avoid exposing skin to the rays of the appliance for distances
less than 50 cm.
Avoid exposing eyes to the rays of the appliance for distanc-
es less than 2.70 m.
All users should be made aware of all aspects of operation
and safety and these instructions should be retained for ref-
erence.
5. MAINTENANCE
The IR Industrial Heaters contain no moving parts and therefore very
little maintenance is required other than to ensure that there is no
excessive build-up of dust/dirt on the reflectors or emitters as this
can cause overheating and premature emitter failure. To clean the
appliance, wipe off with a damp cloth. Wait until it is completely dry
before connecting to the power supply.
6. EMITTER REPLACEMENT
The emitters used in the IR heater are robust and if knocks and shock
vibrations are avoided, they will last for around 3000 hours. They
should be substituted even before if there are signs of aging. Due to
the special sealing and anti-shock design of the heater, the emitters
are not intended to be user replaceable. Please ensure that all emit-
ters are replaced via the WARMTEC service network.

6
DD
CCC
Fig. 2
A
B
B
Fig. 1