Wasserstein Solar Charger Compatible with Blink Video... User manual

User Manual
Solar Charger Compatible with
Blink Video Doorbell

In the Box
Important Tips
To maximize the energy output of the solar charger, remember to
do the following:
• Before installing your doorbell, charge the solar charger for at
least 8 hours under direct sunlight.
This solar charger continuously powers the Blink Video Doorbell.
It contains a 2000 mAh battery.
Page 1
1 x solar charger
1 x set of screws and
wall anchors
2 x backplates (BC1 & BC2)
BC1 BC2
1 x set of small screws

Installation with Blink Video Doorbell
Important:
Make sure your solar charger has been charged in direct sunlight
for at least 8 hours and is installed in an area that receives maximum
sunlight.
Remove any existing doorbell, mount, solar charger, or backplate.
Page 2
• Install your solar charger in an area that receives maximum
sunlight.
• Clean the surface of the solar charger regularly to remove any
dust or dirt that could affect its energy conversion.
Blink Video Doorbells
There are two versions of Blink Video Doorbell:
Three mounting holesTwo mounting holes

Page 3
Installing the Blink Video Doorbell with BC1 backplate.
2. Install the in-box backplate of the BC1 solar charger on top of
the middle cutout with the two small screws provided.
This is used to mount the Blink Video Doorbell with two mounting
holes.
1. Use the two screws and two wall anchors provided to install the
solar charger onto the wall.
Note: Please be aware the correct orientation of the BC1
backplate is as pictured above.

5. Place the top of the Blink Video Doorbell (two mounting holes)
on top of the solar charger cutout, so that the hooks line up.
Press the doorbell firmly against the solar charger then pull
down until it clicks into place.
Page 4
4. Remove any existing batteries from the Blink Video Doorbell.
3. Use the key that comes with your Blink Video Doorbell (two
mounting holes) to remove the backplate.

Note: A red LED will begin flashing for a few seconds to indicate
that it is seeking a connection. If there is no LED flashing,
detach and reinstall (solar charger must be charged for at
least 8 hours before use).
Page 5
Installing the Blink Video Doorbell with BC2 backplate.
This is used to mount the Blink Video Doorbell with three mounting
holes.
1. Use the two screws and two wall anchors provided to install the
solar charger onto the wall.

Page 6
3. Use the key that comes with your Blink Video Doorbell (three
mounting holes) to remove the backplate.
Note: Please be aware the correct orientation of the BC2
backplate is as pictured above.
2. Install the in-box backplate of the BC2 solar charger on top of
the middle cutout with the two small screws provided.

Page 7
4. Remove the battery door and any existing batteries from
Blink Video Doorbell (three mountng holes).
5. Place the top of the Blink Video Doorbell (three mounting holes)
on top of the solar charger cutout, so that the upper hook lines
up. Press the doorbell firmly against the solar charger.
Note: A red LED will begin flashing for a few seconds to indicate
it is seeking a connection. If there is no LED flashing, detach
and reinstall (solar charger must be charged for at least 8
hours before use).

Page 8
Detaching Doorbell from Solar Charger
Blink Video Doorbell (three mounting holes):
1. Use the key that comes with Blink Video Doorbell.
2. Put the key into the opening at the base of the Blink Video
Doorbell. The spring will push inward and the doorbell will
unlock.

Page 9
Blink Video Doorbell (two mounting holes):
1. Use the key that comes with Blink Video Doorbell.
2. Put the key into the opening at the base of the Blink Video
Doorbell.

3. Pull the key towards you and lift up the doorbell to undo the
hook and separate from the backplate.
Page 10
Specifications
7.36 x 4.33 x 1.18 in
2000 mAh
3V DC
0.6 W
ABS + PC
Dimensions:
Battery capacity:
Output voltage:
Power:
Materials:

Get More Support
Scan the QR code below or email us at [email protected].
Blink Video Doorbell is not included.
Wasserstein is a trademark of Dropcases Ltd.
@2022 Amazon.com, Inc. or its affiliates. Amazon,
Alexa, Blink, and all its related marks are trademarks
of Amazon.com, Inc. or its affiliates. Made in China
www.wasserstein-home.com