Watts Premier Filter-Pure UF3 Installation and operating instructions

INSTALLATION, OPERATION AND MAINTENANCE MANUAL
MODEL: Filter-Pure UF3
Watts Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381
Phone: [phone] www.wattspremier.com Fax: [phone]
Part # 199494 Manual Date: 10/10/2012
Please read carefully before proceeding with installation. Your failure to follow any attached instructions or
operating parameters may lead to the product’s failure.
Refer to enclosed warranty for operating parameters to ensure proper use with your water supply.
System Tested and certied by WQA against NSF/ANSI Standards 42 and
53 for the reduction of the claims specied on the performance Data sheet.
Hollow Fiber Technology

Thank you for your purchase of a state of the art Watts Premier Water Treatment system.
Your new Filter-Pure UF3 system is equipped with a unique swivel valve in head push button
assembly. This allows for a simple and sanitary push button lter change that does not require
you to turn off the water source to the ltration system.
This three stage system is equipped with a sediment prelter, a high quality carbon block lter
and the Ultra Filtration membrane.
The sediment lter reduces sand, silt, sediment and rust particles that may be in your water. The
second stage is a heavy duty lead and volatile organic chemical reducing carbon lter block.
This specially formulated block is capable of reducing lead as well as harmful Volatile Organic
Chemicals (See performance data sheet for complete list of VOC’s). It is estimated that VOC’s
are present in one-fth of the nation’s water supplies. These water contaminants can enter ground
water from a variety of sources including localized use of herbicides and pesticides, gasoline or
oil spills, leaking underground fuel tanks, septic system cleaners, and chemicals used in the dry-
cleaning industry. The third stage is our state of the art UF Hollow Fiber Technology membrane.
Ultra ltration is a membrane ltration process which uses standard home water pressure to push
water through its semi permeable membrane. Suspended particles and materials of high molecular
weight are unable to pass through the 0.02 micron UF membrane, allowing only fresher cleaner
water and dissolved minerals to pass through. Historically this separation process has been used
in large municipal water treatment plants and hospitals; however through advances in technology
it is now available to you as a powerful under sink water ltration plant in your home.
Ultra ltration is capable of running at low water pressures, does not require a separate water
holding tank, does not alter the pH of your water and does not require electricity. Due to this the
Filter Pure UF 3 provides a continuous supply of premium quality drinking water directly to your
tap.
System Maintenance
Just because you can not taste it, does not mean that it is not there. Many contaminants in the
drinking water are undetectable to the taste. Additionally, over time if you do not replace the
lter elements, other bad tastes and odors will be apparent in your drinking water. This is why
it is important to change your lters at the recommended intervals as indicated in this system
manual.
When replacing any of the lter elements, pay special attention to any cleaning instructions. Should
you have any further questions please refer to our web site at www.wattspremier.com or call our
customer service department at 1-800-752-5582.
2

Service Record
Date of Purchase:_____________Date of Install:___________ Installed by:_____________
Sediment
Filter
(6 Months)
Date LCV
Block
(6 Months)
LCV
Block
(6 Months)
Sediment
Filter
(6 Months)
Model Number:__________ Serial Number:___________
Date UF
Membrane
(12 Months)
UF
Membrane
(12 Months)
Table of Contents
Service Record...................................................................................................................................... 3
Operational Parameters ........................................................................................................................ 4
Contents of Reverse Osmosis System.................................................................................................. 4
Tools Recommended For Installation.................................................................................................... 4
Plumbing diagram and parts list............................................................................................................ 4
Drill a Hole for the Reverse Osmosis Faucet ........................................................................................ 5
How to use Quick Connect Fittings on Your RO System ...................................................................... 5
Faucet Installation ................................................................................................................................ 6
Blue Tube Connection .......................................................................................................................... 6
Adapt-a-Valve Installation ..................................................................................................................... 7
Green Tube Connection ....................................................................................................................... 7
Mounting System Under Sink ............................................................................................................... 8
Start-up Instructions ............................................................................................................................. 8
Changing The Filter Cartridges ............................................................................................................ 9
Performance Data Sheet ................................................................................................................10-11
Other Products from Watts Premier .................................................................................................... 12
Warranty Registration ....................................................................................................................13-14
Limited Warranty ................................................................................................................................ 15
3

4
Sink
Green
Tubing
Blue
Tubing
HOT COLD
Counter Top
Three Stage Under Counter System (UF-3)
√ 1 Filter-Pure UF3 Unit √ 1 Parts Bag
√ 3 Filters - Attached √ 1 Faucet Assembly
Contents of Under Counter System
Installation must comply with state and local plumbing regulations.
Operational Parameters
If any of the items are missing, please contact Watts Premier prior to installing.
Operating Temperatures:
Maximum 100°F (37.8°C) Minimum 40°F (4.4°C)
Operating Pressure:
Maximum 85 psi (6.0 kg/cm2) Minimum 20 psi ( 1.406 kg/cm² )
pH Parameters:
Maximum 10 Minimum 5
Flow Rate:
0.5 GPM @ 60 psi
Water supply line to the system must be from the cold water supply line.
Item # Part # Description
1 115303 HEAD-PNP-3 STAGE W-/ASOV
2 560080 ADAPT-A-VALVE
3 116113 FAUCET-LK-NAG-BS
4 142000 GREEN TUBING
5 142001 BLUE TUBING
6 105311 SEDIMENT FILTER
7 105371 LVOC CB FILTER
8 105321 UF FILTER
9 199494 MANUAL-FILTER PURE UF3
10 146001 SCREW-#10 PHIL PANHEAD
Part Number List
Tools Recommended For Installation
√ 1/2 Diamond Tipped Hole Saw bit for faucet opening
√ Phillips bit for electric drill √ Sharp Knife
√ 1/2" Open End Wrench √ Electric Drill
√ 1/8" diamond tip bit, pilot hole √ Phillips Screw Driver

5
After drilling, remove all sharp edges and make sure the surroundings
of the sink are cooled before mounting the faucet.
Step 3
Step 4
Determine desired location for the RO faucet on your sink and place
a piece of masking tape over where the hole is to be drilled. Mark the
center of the hole on the tape.
Step 1
Using a variable speed drill set on the slowest speed, drill a 1/8“ pilot
hole through both porcelain and metal casing of sink at the marked
center of the desired location. Use lubricating oil or liquid soap to keep
the drill bit cool (If drill bit gets hot it may cause the porcelain to crack
or chip).
Using a 1/2” diamond tip hole saw, proceed to drill the hole. Keep drill
speed on the slowest speed and use lubricating oil or liquid soap to
keep the hole saw cool during cutting.
Step 2
Counter Top / Porcelain & Stainless Steel Sink
Note: Most sinks are pre drilled with 1 ¼” diameter hole that you can use for your RO faucet.
(If you are already using it for a sprayer or soap dispenser, see step 1)
Porcelain sinks are extremely hard and can crack or chip easily.
Use extreme caution when drilling. Watts accepts no responsibility for
damage resulting from the installation of faucet. Diamond tip bit recommended.
Marble Counter-top
We recommend contacting a qualied contractor for drilling a hole in a marble counter-top.
Drill a Hole for the Faucet
How to use the Quick Connect Fittings
To make a connection, the tube is simply pushed into the tting. The unique locking system holds the tube rmly in place
without deforming it or restricting ow. Use the steps below in reference to any quick connect tube connections.
It is essential that the outside diameter be free of score
marks and that burrs and sharp edges be removed before
inserting into tting.
Fitting grips before it seals. Ensure tube is pushed into
the tube stop.
Push the tube into the tting, to the tube stop. The collet
(gripper) has stainless steel teeth which hold the tube
rmly in position while the O-ring provides a permanent
leak proof seal.
Pull on the tube to check that it is secure. It is a good practice
to test the system prior to leaving site and /or before use.
To disconnect, ensure the system is
depressurized before removing the tube. Push in the col-
lect squarely against face of tting. With the collet held
in this position, the tube can be removed. The tting can
then be reused.

6
Faucet Installation
Insert the faucet shank through the hole in sink
and let it rest on the sink top.
Place the escutcheon chrome plate and the
black rubber washer on the faucet shank.
(Parts found in faucet parts bag).
From the underside of the sink, slide on the
locating washer, lock washer and brass
nut onto the shank. Check orientation of
faucet then tighten brass nut securely.
Step 7
Step 5
Step 6
Escutcheon Plate
Rubber Washer
Locating Washer
Lock Washer
Brass Nut
Tube Insert
Ferrule (Sleeve)
Compression Nut
Locate the 1/4” blue tube in the Filter-Pure Box. The tube has one
straightendand onebentend. Fromthefaucet partsbag, assemble on
the straight end, place the brass nut on the tube rst, then the sleeve
(small tapered end of sleeve must point to the end of tube) and then
inserttheplastic insertallthe wayintothe endofthe tube.(SeePicture)
Blue Tube Connection
Step 8
Step 9
Step 10 Attach the bent, open end of the blue tube into the right side of the
system by pushing it into the quick connect tting (behind Purple UF
Membrane lter head).
Insert the assembled blue tube into the end of the faucet shank until it
stops. Slide brass nut and plastic sleeve down until you can thread nut
onto the faucet shank. Use a wrench to securely tighten the brass nut.

7
Turn off the cold water supply to the faucet by turning the angle stop valve completely off.
Open cold water sink faucet to relieve pressure.
Step 11
Step 12 Choosing the conguration that ts your plumbing, attach the adapt-a-valve as illustrated in
the four photos above.
Adapt-a-Valve Installation
Do not use Teon tape with the Adapt-a-Valve.WARNING:
Caution: Water supply line to the system must be from the cold water supply line only.
Hot water will severely damage your system.
3/8” Conguration
(With Brass Fittings)
* Insert White Washer
1/2” Conguration
(Without Brass
Fittings)
*White
Washer
Hot
Supply Cold
Supply
Hot
Supply Cold
Supply
Verify contents prior to installation:
( 1 ) - Plastic Adapt-a-Valve with black collet
( 1 ) - Brass Adapter no washer
( 1 ) - Brass Adapter with black washer
( 1 ) - White rubber washer
Make sure that the black collet is installed in to the 1/4” opening on the Adapt-a-valve.
Don’t forget to install the white compression washer with the 3/8” conguration.
Brass adapter (A) does not need to be tightened with a wrench, only nger tight.
Black
Collet
A
TIPS:
A
White
Washer
Green Tube Connection - Feed Water
Step 13 Locate the 1/4” Green tube in the Filter-Pure Box. The tube has
one straight end and one bent end. Attach the bent, open end
of the green tube into the left side of the system by pushing it
into the quick connect tting (behind Red Sediment lter head).
Insert the straight, open end of the green 1/4” tube into the
open 1/4” quick connect tting on the plastic water feed valve
making sure the tube is pushed in all the way to the tube stop.
Green Tube
Adapt-a-Valve

8
Mounting System Under Sink
Locate an area best tted for mounting the system. Allow
approximately 2” (5cm) clearance between the bottom of the
lter housing and the oor of the sink cabinet.
Using the mounting holes on the bracket, mark the location for the mounting screws on
the cabinet wall under the sink.
Screw the (2) self tapping screws into the wall at the marked location.
Hang the module on the screws using the mounting holes in the bracket.
Step 14
Step 15
Step 16
Start up Instructions
Congratulations!
You have completed the installation of your new Water Filtration System.
Please Follow the Startup Instructions.
ON
Turn on water supply at angle stop and open theAdapt-a-Valve. Turn
faucet handle to the open position to start the ow of water through
the unit. Run 3 gallons of water through the unit in order to ush out
the normal black carbon nes (it will “sputter” until the air is purged
out) from the unit. Initially, the water may appear cloudy which is due
to tiny air bubbles and it will clear up shortly. Close the faucet when
nished.
(Check frequently over the next 24 hours to ensure no leaks are present)
Step 1
Step 2 Check for leaks. If you have any leaks, shut off the water supply to your system, tighten
any ttings / housings and restart unit.

Place a towel under the lter module to catch any excess water that
may drip out from the lters during the changeover.
Step 1
Your system is equipped with valved heads which will automatically turn off the
water supply to each lter when the lter is released, thus you do not need to turn
off the incoming water supply at the Adapt-a-Valve. The faucet must be off when
lters are replaced. To make the removal of the lter cartridges easier, the heads
& cartridges may be swiveled up to 90 degrees as shown in the pictures below.
Step 2
To install a lter cartridge: Remove the seal cap and insert
the cartridge into the valved head until you hear an audible “click”
(the button does not need to be pressed to install new lters).
Step 3
To remove a lter cartridge: Push & hold the button on the
valved head above the lter. Pull cartridge downward (from the
head) to remove. Release button and discard old lter.
Changing The Filter Cartridges
√ One sediment lter (Red Label P/N: 105311)
√ One LVOC Block (Blue Label P/N: 105371)
Replace:
6 Month System Maintenance
9
√ One sediment lter (Red Label P/N: 105311)
√ One LVOC Block (Blue Label P/N: 105371)
√ One UF Membrane (Purple Label P/N: 105321)
Annual System Maintenance
Replace:
Note: If the new lter cartridge won’t snap in easily or pops off it may be
due to high incoming water pressure. Relieve pressure to the system by
turning off the water supply using the adapt-a-valve and then install the
cartridge. Once the cartridge is seated, turn the water supply back on to
your unit.

Performance Data Sheet
Watts Premier Inc.
8716 W Ludlow Drive Suite #1
Peoria, AZ 85381
FILTER-PURE UF3, 531130
GENERAL USE CONDITIONS:
1. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or
after the system. Systems certied for cyst reduction may be used on disinfected waters that may contain lterable cysts.
2: Operating Temperature: Maximum 100o F (40.5o C) Minimum 40o F (4.4o C)
3: Operating Water Pressure: Maximum 85-psi (5.98 kg/cm2) Minimum 20-psi
4: Maximum ow Rate: 0.50 gpm (1.89 lpm)
5: Rated Capacity: 150 Gallons (570 liters)
10
Substance Percent
Reduction
Inuent Challenge
Concentration
(mg/L unless noted)
Maximum Permissible
Product Water
Concentration
ALACHLOR* >98% 0.05 0.001
ATRAZINE* >97% 0.1 0.003
BENZENE* >99% 0.081 0.001
BROMODICHLOROMETHANE (TTHM)* >99.8% 0.300 +/- 0.30 0.015
BROMOFORM (TTHM)* >99.8% 0.300 +/- 0.30 0.015
CARBOFURAN (Furadan)* >99% 0.19 0.001
CARBON TETRACHLORIDE* 98% 0.078 0.0018
CHLOROBENZENE (Monochlorobenzene)* >99% 0.077 0.001
CHLOROFORM (TTHM)* >99.8% 0.300 +/- 0.30 0.015
CRYPTOSPORIDIUM (see Cyst) 99.99% minimum 50,000/mL 99.95%
CYST 99.99% minimum 50,000/mL 99.95%
2, 4-D* 98% 0.110 0.0017
DBCP (see Dibromochloropropane)* >99% 0.052 0.00002
1,2-DCA (see 1,2-DICHLOROETHANE)* 95% 0.088 0.0048
1,1-DCE (see 1,1-DICHLOROETHYLENE)* >99% 0.083 0.001
DIBROMOCHLOROMETHANE
(TTHM;Chlorodibromomethane)* >99.8% 0.300 +/- 0.30 0.015
DIBROMOCHLOROPROPANE (DBCP)* >99% 0.052 0.00002
o-DICHLOROBENZENE (1,2 Dichlorobenzene)* >99% 0.08 0.001
p-DICHLOROBENZENE (para-Dichlorobenzene)* >98% 0.04 0.001
1,2-DICHLOROETHANE (1,2-DCA)* 95% 0.088 0.0048
1,1-DICHLOROETHYLENE (1,1-DCE)* >99% 0.083 0.001
CIS-1,2-DICHLOROETHYLENE* >99% 0.17 0.0005
TRANS-1,2- DICHLOROETHYLENE* >99% 0.086 0.001
1,2-DICHLOROPROPANE (Propylene Dichloride)* >99% 0.08 0.001
CIS-1,3- DICHLOROPROPYLENE* >99% 0.079 0.001
DINOSEB* 99% 0.17 0.0002
EDB (see ETHYLENE DIBROMIDE)* >99% 0.044 0.00002
ENDRIN* 99% 0.053 0.00059
This system has been tested according to NSF/ANSI Standard 42 and 53 for the reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration less than or
equal to the permissible limit for water leaving the system, as specied in NSF/ANSI 42 and 53. Testing performed
under standard laboratory conditions, actual performance may vary.
RECOMMENDED REPLACEMENT PARTSAND CHANGE INTERVAL:
Note: Depending on incoming feed water conditions replacement time frame may vary.
Description Part Number Change Time Frame Cost
Stage 1: sediment: 105311 6 Months $ 9.95*
Stage 2: Lead + VOC Block 105371 6 Months $29.95*
Stage 3: UF Membrane 105321 12 Months $35.50*
*All prices subject to change without notice

11
Substance Percent
Reduction
Inuent Challenge
Concentration
(mg/L unless noted)
Maximum Permissible
Product Water
Concentration
ENTAMOEBA (See CYST) 99.99% minimum 50,000/mL 99.95%
ETHYLBENZENE* >99% 0.088 0.001
ETHYLENE DIBROMIDE (EDB)* >99% 0.044 0.00002
FURADAN (see CARBOFURAN)* >99% 0.19 0.001
HALOACETONITRILES (HAN)*
BROMOCHLOROACETONITRILE 98% 0.022 0.0005
DIBROMOACETONITRILE 98% 0.024 0.0006
DICHLOROACETONITRILE 98% 0.0096 0.0002
TRICHLOROACETONITRILE 98% 0.015 0.0003
HALOKETONES (HK):*
1,1-DICHLORO-2-PROPANONE 99% 0.0072 0.0001
1,1,1-TRICHLORO-2-PROPANONE 96% 0.0082 0.0003
GIARDIA LAMBLIA (see Cyst) 99.99% minimum 50,000/mL 99.95%
HEPTACHLOR* >99% 0.25 0.00001
HEPTACHLOR EPOXIDE* 98% 0.0107 0.0002
HEXACHLOROBUTADIENE
(Perchlorobutadiene)* >98% 0.044 0.001
HEXACHLOROCYCLOPENTADIENE* >99% 0.060 0.000002
LEAD pH 6.5 96% 0.15 +/- 10% 0.010
LEAD pH 8.5 99% 0.15 +/- 10% 0.010
LINDANE* >99% 0.055 0.00001
METHOXYCHLOR* >99% 0.050 0.0001
METHYLBENZENE (see TOLUENE)* >99% 0.078 0.001
MONOCHLOROBENZENE
(see CHLOROBENZENE)* >99% 0.077 0.001
PCE (see TETRACHLOROETHYLENE)* >99% 0.081 0.001
PENTACHLOROPHENOL* >99% 0.096 0.001
PERCHLOROBUTADIENE
(see HEXACHLOROBUTADIENE)* >98% 0.044 0.001
PROPYLENE DICHLORIDE
(see 1,2 -DICHLOROPROPANE)* >99% 0.080 0.001
SIMAZINE* >97% 0.120 0.004
SILVEX (see 2,4,5-TP)* 99% 0.270 0.0016
STYRENE (Vinylbenzene)* >99% 0.15 0.0005
1,1,1-TCA
(see 1,1,1 - TRICHLOROETHANE)* 95% 0.084 0.0046
TCE (see TRICHLOROETHYLENE)* >99% 0.180 0.0010
1,1,2,2- TETRACHLOROETHANE* >99% 0.081 0.001
TETRACHLOROETHYLENE* >99% 0.081 0.001
TOLUENE (Methylbenzene)* >99% 0.078 0.001
TOXOPLASMA (See CYST) minimum 50,000/mL 99.95%
2,4,5-TP (Silvex)* 99% 0.270 0.0016
TRIBROMOACETIC ACID* 0.042 0.001
1,2,4 TRICHLOROBENZENE (Unsymtrichlorobenzene)* >99% 0.160 0.0005
1,1,1-TRICHLOROETHANE (1,1,1-TCA)* 95% 0.084 0.0046
1,1,2-TRICHLOROETHANE* >99% 0.150 0.0005
TRICHLOROETHYLENE (TCE)* >99% 0.180 0.0010
TRIHALOMETHANES (TTHM) (Chloroform; Bromoform;
Bromodichloromethane; Dibromochloromethane) >99.8% 0.300 +/- 0.30 0.015
Unsym-Trichlorobenzene (see 1,2,4-
TRICHLOROBENZENE)* >99% 0.160 0.0005
Vinylbenzene (see STYRENE)* >99% 0.150 0.0005
XYLENES (TOTAL)* >99% 0.070 0.001
Maximum Permissible
Contaminant  InuentChallengeConcentrationPercentReductionAchieved ProductWaterConcentration
Aesthetic Chlorine Taste & Odor 2.0 mg/L + 10% 97% > = 50%
Particles Class IV 13,000 Particles /ml 96% > = 85%
Size >= 15 ug to < 30 ug
California Proposition 65 Warning
WARNING: this product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. (Installer:
California law requires that this warning be given to the consumer). For more information: www.wattsind.com/prop65.

Watts Premier has other ne water ltration products and accessories to enhance your water and to
compliment your water ltration system. Listed on this page are only a few of the items we offer. Visit
our web site at www.wattspremier.com or call our Customer Service Representatives at
1-800-752-5582 (inside USA) 1-480-675-7995 (outside USA) for more products.
*All prices subject to change without notice.
Watts Premier Hot Water Recirculation System
Bring convenience and savings to your home, giving you hot water instantly
at every faucet, when you need it. This unique product is easy to install and
not only provides you with the convenience of hot water when you need it, but
saves an average of over 15,000 gallons per year.
Part No. 500800 *$229.99/ea
Whole House Filter
Great for sediment problems such as in well water supply or areas where dirt
and rust particles are a problem. Includes three 50 micron sediment lters
and wrench
(3/4” ports)
Part No. 500223 *$42.95/ea
Replacement lter
Part No. 304007 *$ 4.50/ea
PoolDocTM accurately measures pool and spa chemistry and provides
instructions on how to bring the pool/spa back into balance.
Part No. 164040 *$189.99/ea
Pool Doc Pool & Spa Water Tester
Whole House High Performance Water Pressure Regulator
Provides water pressure control solutions for residential, commercial, and
industrial applications. Offers durability and years of continuous trouble free
operation.
Part No. 107001 *$69.95 each
Other Products from Watts Premier
12
Water Pressure Gauge
This gauge mounts onto your outside hose connection to accurately show your
home’s water pressure up to 300 psi. A red needle shows peak overnight
pressure, which may exceed readings during the day. High pressure readings
may indicate the need for a pressure regulator to prevent damage to appliances.
Part No. 261003 *$11.50/ea

4 Ways to Register
1. On-line at www.wattspremier.com
2. Call in your information 1-800-752-5582
3. Fax in your information 623-866-5666
First Name:_________________________ Last Name:____________________________
Address: ________________________________________ City: ____________________
State: _______________________________________ Zip Code: ___________________
Country: USA CANADA MEXICO OTHER ____________
Phone # ______-__________ -__________ Email Address: ______________________
Date of Purchase: ___________________ Date of Install: _______________________
Installed By: SELF Plumbing Professional Where Purchased: ____________
Model Number: _______________________ Serial Number: ____ - __________
Watts Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381
Phone: [phone] www.wattspremier.com Fax: [phone]
Register your product on-line and receive a 5% discount on your next on-line order, Plus receive reduced shipping.
4. Mail in the information.
Please complete the form below. Mail to: Watts Premier
8716 W Ludlow Drive Sutie #1
Peoria, AZ 85381
Fax this form directly to us.
Call and we will enter your registration information for you.
XXXXX XXXXXX
-
Watts Premier Inc. is concerned for the safety of your personal information. Watts Premier collects personal information when you register
with Watts Premier. This information is stored in our data base and we do not rent, sell, or share personal information with other people
or nonafliated companies. We reserve the right to send you certain types of communications such as direct mail, email, or by telephone
relating to our products or products that you have purchased. We limit access to your personal information to those employees who will
directly provide you with services or products in order to do their jobs. We want to offer you four ways to communicate with us. 1.Online,
2.Fax, 3.Telephone, and 4. Mail the form below. By registering your product you will receive the full benet of our warranty. Watts Premier
will also send you a semiannual lter change reminder beginning six months from date of installation. To insure the highest quality of your
water, lters should be replaced every 6 months. If you have any questions or comments please give us a call at 1-800-752-5582 M-F
8:00am -5:00pm MST.
Registering will
insure you
receive Watts
FREE
Filter
Reminder
Notice
Thank you for selecting Watts Premier for your water ltration needs.
WARRANTY REGISTRATION
13

WARRANTY REGISTRATION
Please Fill out and keep for your Records
Insert into envelope and return to Watts Premier
First Name:_________________________ Last Name:____________________________
Address: ________________________________________ City: ____________________
State: _______________________________________ Zip Code: ___________________
Country: USA CANADA MEXICO OTHER ____________
Phone # ______-__________ -__________ Email Address: ______________________
Date of Purchase: ___________________ Date of Install: _______________________
Installed By: SELF Plumbing Professional Where Purchased: ____________
Model Number: _______________________ Serial Number: ____ - __________
Iowa Department of Public Health - Sales in Iowa require this to be completed, signed and returned.
These signatures will be retained on le for two years.
XXXXX XXXXXX
-
Watts Premier
8716 W Ludlow Drive Suite #1
Peoria, AZ 85381
14

8716 W Ludlow Drive Suite #1 •Peoria, AZ 85381
Limited Warranty
What your Warranty Covers:
If any part of your WATTS PREMIER FILTER PURE UF3 unit is defective in workmanship (excluding replaceable lters ),
return unit after obtaining a return authorization (see below), within 3 years of original retail purchase, WATTS PREMIER
will repair or, at WATTS PREMIER’S option, replace the system at no charge.
How to obtain Warranty Service:
For warranty service, call 1-800-752-5582 for a return authorization number. Then, ship your unit to our factory, freight and
insurance prepaid, with proof of date of original purchase. Please include a note stating the problem. Premier will repair it,
or replace it, and ship it back to you prepaid.
What this warranty does not cover:
This warranty does not cover defects resulting from improper installation, (contrary to WATTS PREMIER’S printed
instructions), from abuse, misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties, re,
ood, freezing, environmental factors, water pressure spikes or other such acts of God.
This warranty will be void if defects occur due to failure to observe the following conditions:
1. The Filter-Pure UF3 System must be hooked up to a potable municipal or well cold water supply.
2. The pH of the water must not be lower than 5 or higher than 10.
3. The incoming water pressure must be between 20 and 85 pounds per square inch.
4. Incoming water to the Counter Top cannot exceed 100 degrees F (38 degrees C.)
This warranty does not cover any equipment that is relocated from the site of its original installation.
This warranty doe not cover any charges incurred due to professional installation.
This warranty does not cover any equipment that is installed or used outside the United States of America and Canada.
LIMITATIONS AND EXCLUSIONS:
WATTS PREMIER WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. WATTS PREMIER WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES, INCLUDING TRAVEL EXPENSE, TELEPHONE CHARGES, LOSS OF REVENUE, LOSS OF TIME,
INCONVENIENCE, LOSS OF USE OF THE EQUIPMENT, AND DAMAGE CAUSED BY THIS EQUIPMENT AND ITS FAILURE TO
FUNCTION PROPERLY. THIS WARRANTY SETS FORTH ALL OF PREMIER’S RESPONSIBILITIES REGARDING THIS EQUIPMENT.
OTHER CONDITIONS:
If WATTS PREMIER chooses to replace the equipment, WATTS PREMIER may replace it with reconditioned equipment. Parts used in
repairing or replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the remainder of
the original warranty period, whichever is longer. This warranty is not assignable or transferable.
YOUR RIGHTS UNDER STATE LAW:
Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply. This warranty gives you specic legal rights,
and you may have other legal rights which vary from state to state.