Waudio DQM Series User manual

Order codes:
MIC82 - DQM 800H 823-830Mhz and 863-865Mhz
MIC82A - DQM 800BP 823-830Mhz and 863-865Mhz
MIC81 - DQM 600H 606-614Mhz
MIC81A - DQM 600BP 606-614Mhz
DQM Series
UHF Radio Microphone System
User Manual

www.prolight.co.uk DQM Series User Manual 2
Safety adviceSafety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Before your initial start-up, please make sure that there is no damage caused during transportation.
• Should there be any damage, consult your dealer and do not use the equipment.
• To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
• Please note that damages caused by user modications to this equipment are not subject to warranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and
the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.
In case of malfunction this unit should be returned for service or inspection.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and/or property.
• Never let the power cable come into contact with other
cables. Handle the power cable and all mains voltage
connections with particular caution!
• Never remove warning or informative labels from the unit.
• Do not open the equipment and do not modify the unit.
• Do not connect this equipment to a dimmer pack.
• Do not switch the equipment on and off in short intervals,
as this will reduce the system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when
equipment is not in use or before cleaning! Only handle
the power-cable by the plug. Never pull out the plug by
pulling the power-cable.
• Make sure that the available voltage 14V DC, 1200mA.
(240V AC~50Hz power supply included)
• Make sure that the power cable is never crimped or
damaged. Check the equipment and the power cable
periodically.
• If the equipment is dropped or damaged, disconnect the
mains power supply immediately and have a qualied
engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic
temperature uctuation (e.g. after transportation),
do not connect power or switch it on immediately.
The arising condensation might damage the equipment.
Leave the equipment switched off until it has reached
room temperature.
• If your product fails to function correctly, stop use
immediately. Pack the unit securely (preferably in the
original packing material), and return it to your Pro Light
dealer for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be
carried out by a qualied technician. THIS UNIT CONTAINS
NO USER SERVICEABLE PARTS.
• This xture is for professional use only - it is not designed
for or suitable for household use. The product must be
installed by a qualied technician in accordance with local
territory regulations. The safety of the installation is the
responsibility of the installer. The xture presents risks of
severe injury or death due to re hazards, electric shock
and falls.
• WARRANTY: One year from date of purchase.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM MOISTURE,
RAIN AND LIQUIDS, AND
OUT OF DAMP/HUMID
ENVIRONMENTS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.prolight.co.uk DQM Series User Manual 3
Product overview & technical specications
DQM series wireless microphones are quad UHF handheld systems designed for the professional user. Available in two
versions, the systems offer either 8MHz across 110 selectable frequencies for the 606-614Mhz Channel 38 band (DQM 600)
or 9MHz+2Mhz across 99 selectable frequencies for the 823-832Mhz Channel 65 and 863-865Mhz Channel 70 band (DQM
800); both systems utilise a diversity, full width receiver for the ultimate in RF stability.
Outstanding vocal reproduction and stable wireless connectivity allow freedom of movement on stage. These systems offer
crystal clear sound reproduction and rock solid reliability. Handheld transmitters feature ergonomic design with a rugged
housing to stand up to the rigours of the road. The exibility of the handheld systems may be increased by purchasing the
additional DQM 600BP or DQM 800BP.
DQM Series UHF Radio Microphone System
Specications DQM 800H DQM 600H
Operating frequency 823Mhz-830Mhz and
863Mhz-865Mhz 606.0Mhz-614.0Mhz
Power supply 14V 1.2A (adaptor supplied)
Order code MIC82 MIC81
• UHF band, Phase Lock Loop (PLL)
offering stable RF transmission
• Frequency groups and a group of
users set their own frequencies and
storage, multiple sets of compatible
frequency presets
• Tuning bandwidth up to 8MHz can
provide 110 selectable frequencies
for the 606-614Mhz CH38 band
and 9MHz+2Mhz with 99 selectable
frequencies for the 823-832Mhz
CH65 and 863-865Mhz CH70 band
• OLED display offers a wide viewing
angle while remaining bright in
darkened conditions
• Frequency, Channel, RF and
AF signal strength meters
• 1U rack metal housing with integrated
brackets, include antenna cable
interface for front-mount antenna
• Combined use Jog Dial button
operation for fast menu navigation
• Integrated antenna splitter for
reduced RF interference
• Balanced XLR output for
each channel plus unbalanced
mixed output
• Automatic frequency SCAN function
• IR infrared frequency synchronisation
via infrared interface
• Noise locking
• Mute circuitry for reduced noise
• Flat frequency response: 50Hz-16KHz
• Dynamic, cardioid handheld
microphone capsule
• Battery type: AA 1.5V DC Alkaline
(not supplied)
• 1U full width rack mount receiver
In the handheld system box:
1 x receiver, 2 x removable antenna, 2 x antenna
extension cables, 4 x handheld transmitters, 1 x
14V 1.2A mains PSU & 1 x user manual
In the beltpack box:
1 x beltpack transmitter, 1 x lavalier (tie clip)
microphone, 1 x headset microphone
& 1 x user manual
Receiver specications
• Radio frequency sensitivity:
6dBμV, S/N>80dB
• Working range: Straight line
distance 60 m
(Note: The actual range depends
on RF signal absorption, reection
and interference)
• Mute control mode: Noise locking
• Combined frequency response:
50Hz-16KHz (±3dB)
• Total harmonic distortion (THD):
<0.5% @ 1KHz
• Panel display: OLED display x 4
• Receiver dimensions (H x W x D):
45 x 482 x 215mm
• Weight: 2.0kg

www.prolight.co.uk DQM Series User Manual 4
Receiver front
panel identication:
1. Power Switch
On/Off control for the system receiver.
2. IR Transceiver
The IR transceiver is used to
communicate with the systems
transmitters during setup.
3. ACT Button
Allows the user to activate the IR sync
function for the selected channel.
4. OLED Display
The receiver features a backlit display
allowing the user to see information
about the receiver including frequency,
channels, audio and RF status.
5. Volume Control
The receivers output volume is
adjustable. Turn the level control anti
clockwise to the lowest setting, or
turn clockwise to adjust to the highest
setting. Each channel features an
independent volume control.
6. SCAN button
Press the SCAN button to active the
receivers scan function, the receiver
will survey the wireless signals available
within reception range.
7. MENU Control
Rotary jog wheel with push to enter
function. This allows the user to
navigate the receivers menu system.
8. SW Button
Press the SW select button to access
the menu for each individual receiver
or all of the receivers. The display will
dim/highlight to show which receiver
channels are selected.
Receiver rear panel
identication:
9. DC Power Input
The receiver is powered by a standard
DC power input 12-18V DC, 800mA
regulated voltage supply.
10. Audio (MIX) Output
6.35mm (1/4”) jack socket outputting
an unbalanced, line level audio output
featuring both audio channels.
11. Antenna – Channel A/B & C/D
The antenna receives the RF radio
signal from the transmitter unit. For
optimum reception, orientate vertically.
Keep away from obstacles such as
walls, oors, power ampliers and
steelwork.
12. Balanced Audio Outputs A/B/C/D
Individual, balanced audio outputs via
3 pin XLR for audio channel.
Operating instructions
1 3 4 5 6 7
910 11 12
2 8

www.prolight.co.uk DQM Series User Manual 5
Operating instructions
Operation:
• Carefully, connect the antennae and lift into the vertical position ensuring clear line of sight to the transmitter.
• RF Signals may be affected by many factors. Avoid placing the receiver near metallic objects or near other sources of RF
transmission including IEM transmitters and WiFi access points. The receivers should be located as close to stage as pos-
sible to minimise signal degradation due to large crowds, stage structures or long distances.
• Connect the included power supply to a suitable 240V AC~ 50Hz mains voltage outlet and plug the DC connector into the
DC Power Input on the rear panel of the receiver (12-18V DC, 800mA minimum)
• Using the supplied audio cable, connect the MIX OUT on the rear panel of the receiver for all four audio channels to the
mixer’s audio line input, alternatively the receiver also features balanced XLR outputs, one for each channel allowing full
control of each channel.
• Switch on the power to the receiver, checking the display backlight illuminates
• Open the battery compartment on the transmitter (Beltpack – squeeze the buttons on the side and open the battery door
forwards away from the belt clip. Handheld - unscrew the lower portion). Install the appropriate batteries into the transmit-
ter, taking care to observe the orientation and polarity. Only use high quality, alkaline type batteries. Ret the battery com-
partment cover carefully.
• Switch on the transmitter, when switched on the display on the transmitter will illuminate. If the display does illuminate or
glows dimly, the battery will require replacement.
• Follow the IR Sync and Frequency Setup Operation fully to ensure the transmitters are linked correctly to the receiver unit.
Failure to follow this fully will prevent the microphone system from operating correctly. Factory presets may not be suitable
for use.
• Adjust the volume on the front panel of the receiver for each of the channels to suit the gain structure of the mixer they are
to be connected into.
• Channel (Frequency) Setup:
Press the SW button to access the menu function and select a channel to be congured. As each channel is selected the
display will remain illuminated and the other channels will dim. Press the MENU dial to select the GROUP and CHANNEL.
The full list of selectable frequencies, groups and channels can be found on page 7 of this manual. Group “U” will allow
the user to advanced access to tune the receiver by selecting either 1Mhz or 25Khz frequency steps. This mode may allow
selection of frequencies which overlap or cause inter modulation with other receiver channels.
• IR Sync Operation:
After making changes to the settings on the receiver, the IR Sync operation should be carried out to ensure the settings are
replicated into the transmitter to ensure correct operation.
Place the transmitter within 0.5m of the receiver with the IR receiver pointed towards the receiver’s IR window ensuring both
transmitter and receiver are powered on. Press the ACT button and the receiver will begin IR Sync. When completed the
receiver will show “Success” and the transmitter will then change to match the settings on the receiver. The microphone is
now ready for use. Each transmitter should be synchronised individually.
• Frequency Scan Mode:
To allow the user to select a frequency free from interference, the receiver features a frequency scan mode. Firstly, switch
on any transmitters from other systems in the vicinity. Ensuring any transmitters are powered on, press the SCAN button to
activate the receivers scan function on each of the individual channels one at a time.
Once the receiver has completed the scan function and located a frequency suitable for use the display will show “Scan
Complete”. Should the receiver be unable to detect a clear frequency, the receiver will show “Scan Fail”. In this instance,
either manual selection of frequency may be required or if the local environment is busy with RF transmissions (i.e. if many
other radio microphones are in use) then a change of location or equipment may be required.

www.prolight.co.uk DQM Series User Manual 6
Operating instructions
Beltpack transmitter
identication:
1. Antenna
2. Mute Button
3. Microphone
Input
4. LCD Display
5. On / Off Switch
6. IR Transceiver
7. Mode Button
8. Set Button
9. Battery
compartment
(care should
be taken to
observe
battery
polarity)
10. Battery
Cover
1 2 3
6
4
9
10
7
8
5
Belt pack transmitter
plus headset and
lavalier microphones
to be used in place
of the handheld
transmitter.
Optional DQM Series Add On Beltpack Kits
Specications DQM 800BP DQM 600BP
Operating
frequency
823Mhz to 830Mhz and
863Mhz to 865Mhz 606.0Mhz-614.0Mhz
Battery type 2 x 1.5V AA (not supplied)
Order code MIC82A MIC81A
NOTE:
The DQM 600/800 system is shipped with four handheld transmitters. The receiver in this system features a quad
channel receiver allowing four handheld microphones to be used simultaneously, an additional belt pack kit maybe
purchased if required to be used in place of the handheld transmitters. Each receiver channel in this system may only
be used with one transmitter at any one time. If the user attempts to power on, and use two transmitters on the same
receiver frequency the system will malfunction and not operate correctly as one transmitter will cut out the RF Radio
signal to the second transmitter.
Available in two frequency ranges, the DQM 800 series is for use in the 823-832Mhz CH65 and 863-865Mhz CH70
band (CH70 is license free in the UK) while the DQM 600 series is for use in the 606-614Mhz CH38 band. To operate
microphones in the 823-832Mhz CH65 or 606-614Mhz CH38 band the user must obtain a license from the relevant
authorities in the UK before using the product. Outside of the UK, the user must clarify the frequencies with their local
government ofce responsible for radio microphone frequencies.
Handheld transmitter
identication:
1. Grille
2. LCD Display
3. IR Transceiver
4. Power Switch
5. Battery
compartment
1
2
3
4
5
Handheld microphone specications
• Handheld Transmitter
• Pickup gain: Fixed
• Transmitter power:10mW
• Current drain: Standard <130mA
• Display method : LCD
• Cartridge: Dynamic cardioid cartridge
Beltpack specications
• Pickup gain: Adjustable gain
• Transmitter power: 10mW
• Current drain: Standard <130mA
• Display method: LED
• Pickup type: Cardioid condenser cartridge

www.prolight.co.uk DQM Series User Manual 7
Troubleshooting & Frequencies
Troubleshooting:
Problem Possible cause Solution
Receiver – no sound No RF signal
Check antenna placement for interference from metallic
objects (e.g. rack enclosures) or other sources of
RF interference (e.g. in ear monitor transmitters)
IR Sync operation has not been carried out successfully.
Complete channel selection and IR sync in accordance
with this manual.
Receiver – no LED Power button is in the OFF position. DC power adapter
is not plugged in Turn on the power button plug in the power adapter
Microphone - no sound
but LED indicators are lit
Mic transmitter is out of range. Mic is switched off. Mic
volume it turned down. Batteries in mic are not installed
properly. Receiver is not connected to an amp or mixer.
Ensure that the mic is within range. Turn on the mic switch.
Turn up the mic volume on the receiver. Reinstall or use new
batteries. Connect an output cable to an amp or mixer
Distorted sound or feedback
The 4 mics may be too close together. Batteries are running
out of charge. Mic volume may be too high. Possible
interference from another source.
Increase the distance between mics. Replace the batteries.
Reduce the volume. Move the system away from other
electric sources.
Frequencies:
DQM 800H Series Frequencies:
Channel Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 Group 9 Group 10
CH1 823.000 864.950 863.100 830.850 863.100 823.000 823.000 823.100 823.200 826.900
CH2 823.875 864.350 863.500 829.000 863.500 823.375 823.875 823.500 823.600 831.300
CH3 824.500 863.975 864.200 828.225 864.300 826.125 824.500 824.100 824.200 863.000
CH4 827.175 863.150 864.800 825.250 864.900 826.575 827.175 824.900 825.000 863.600
CH5 831.800 863.525 824.675 827.975 829.625 826.100 826.200 864.000
CH6 864.425 864.200 831.800 831.800 827.700 827.800
CH7 823.375 863.175 824.500 865.000 829.900 830.000
CH8 824.900 863.600 824.900 823.375 864.700 864.800
CH9 826.575 825.975 827.175 824.900 825.275 825.375
CH10 827.975 864.650 829.625 825.425 826.575 826.675
CH11 829.625 830.350 826.125 828.400 828.500
CH12 830.350 823.875 826.575 830.950 831.050
CH13 863.425 825.425 827.975
CH14 864.900 828.525 828.525
CH15 825.425 830.350
CH16 826.125 864.050
CH17 828.525
DQM 600H Series Frequencies:
Channel Group 1 Group 2 Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 Group 9 Group 10
CH1 606.175 607.000 606.275 606.825 607.000 606.625 606.500 608.000 606.975 606.500
CH2 608.050 607.350 606.875 607.250 607.625 607.675 607.350 608.925 607.600 606.875
CH3 609.125 608.400 607.800 607.975 608.975 608.525 608.000 610.075 609.675 607.375
CH4 609.525 608.850 608.200 608.900 609.500 610.175 611.000 611.475 612.725 608.000
CH5 611.775 610.875 610.925 610.350 610.750 610.625 611.400 613.125 606.475 608.425
CH6 612.600 611.625 611.725 611.175 612.250 611.575 613.275 606.500 608.000 609.375
CH7 613.100 612.175 613.350 612.525 612.975 612.175 606.875 606.875 608.525 609.775
CH8 613.825 613.825 613.850 613.150 613.400 613.375 609.325 607.375 609.225 610.475
CH9 606.775 613.175 610.475 611.550 611.775 607.275 609.775 608.400 610.275 611.000
CH10 607.550 606.475 612.050 608.350 606.550 611.275 610.475 609.625 611.075 611.400
CH11 611.200 612.000 610.675 611.625 612.200
CH12 612.025 613.450 612.800
CH13 606.100 613.275

www.prolight.co.uk DQM Series User Manual 8
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government ofce, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for disposal.
WEEE notice