Waycon MSB Series User manual

FIRST STEPS
INSTALLATION GUIDE
Magnetostrictive Sensor Series MSB
For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/
MOUNTING INSIDE A CYLINDER
Way on Positionsmesstechnik GmbH would like to thank you for the trust you have placed in us and our
products. This manual will make you familiar with the installation and operation of our magnetostrictive
sensors. Please read this manual carefully before initial operation!
Unpacking and checking:
arefully lift the device out of the box by grabbing the housing. After unpacking the device, check it for
any visible damage as a result of rough handling during the shipment. heck the delivery for
completeness. If necessary consult the transportation company, or contact Way on directly.
The cylinder head (in which the threaded hole will be drilled for inserting the transducer) must be made of
non-magnetic material. The residual magnetization caused by drilling the threaded hole must be less than
4 Gauss.
MSB...F1

MOUNTING INSIDE A CYLINDER
INSTALLATION GUIDE
Magnetostrictive Sensor Series MSB
For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/
Thread M18x1,5
The sealing surface must be free from
scratches longitudinal or spiral.
Ro 1.6 μm for sealing with NON-pulsating pressure
Ro 0.8 μm for seals with pulsating pressure
Su ested o-rin :
PARKER 6-349 15,4x2,1
Material: Viton 90° Shore-A
Mixes: PARKER N552-90
MSB...F2:
measurement range

TECHNICAL DRAWING
MSB...F2
MSB...F1
Detail X

INSTALLATION GUIDE
Magnetostrictive Sensor Series MSB
For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/
ELECTRICAL CONNECTION
ELECTRICAL CONNECTION MSB...N/K/E-F1
MSB...N-F1 MSB...K-F1 MSB...E-F1 Cable
0.1...10.1 V 0.1...5.1 V yellow
Output GND Output GND Output GND pink
Pow er Supply + Pow er Supply + Pow er Supply + brow n
Pow er Supply GND Pow er Supply GND Pow er Supply GND blue
4...20 mA
- The transducer must be installed in a grounded metallic cylinder.
- The braiding of the shielded transducer connection cable must be connected to the case of the female
connector so that the shielding is connected to the transducer case.
- The cable shielding on PL side must be isolated.
- If the transducer is installed in a cylinder isolated from the ground, the cable shielding on PL side must
be grounded.
- The transducer must be installed away from sources of magnetic fields, both static and 50 Hz (electric
motors, solenoids, etc.).
- The 24 VD feed must be dedicated to the transducers or must be drawn directly from the power
terminals and as near as possible.
- The sensors must be powered with non-distributed networks and always at lengths of less than 30 m.
- The magnetic cursor must be installed by placing a non-magnetic spacer (made of brass, aluminium,
stainless steel or plastic) between the piston surface and the cursor.
MSB
Standard Installation (recommended)

ELECTRICAL CONNECTION MSB...S-F1
DIGITAL OUTPUT MSB...S-F1
Series MSB... -S magnetostrictive transducers supply digital outputs in START/STOP format with RS422
differential serial transmission. The transducer requests an initialisation pulse that launches sampling.
The following pulses are transmitted on the outputs:
Start: the initialisation pulse retransmitted
Stop: the pulse corresponding to the position of each magnet.
The time between the Start pulse and the subsequent Stop pulses is proportional to the position of each
magnet according to the “magnetostrictive wave propagation speed” constant, equal to about 2900
m/sec.
P = Time * 2900 m/sec
The correct propagation speed for each product is shown on the product label.
Resolution in terms of metres is linked to the resolution used to measure time
1 μSec (1 MHz ) ==> 2.9 mm
10 nSec (100 MHz ) ==> 0.029 mm
1 nSec (1 GHz ) ==> 2.9 μm
The measurement reference is the leading edge of the pulse. Optimum width of the interrogation pulse
is 3 μsec, but the transducer works correctly for times from 1.5 to 5 μsec.
MSB...S-F1 Cable
Output + grey
Output - green
Input + yellow
Input - pink
Pow er Supply + brow n
Pow er Supply GND blue
In case of cable length shortening,
after cutting the cable take care of
soldering and insulating the green
and grey wires together

DIGITAL OUTPUT MSB...S-F1
INSTALLATION GUIDE
Magnetostrictive Sensor Series MSB
For more information please see the data sheet at www.waycon.biz/products/magnetostrictive-transducers/
ELEKTRISCHER ANSCHLUSS CANopenELECTRICAL CONNECTION MSB...F2
onnector output M12
MSB...F2
MSB...N-F2 MSB...K-F2 MSB...E-F2 PIN
0.1...10.1 V 0.1...5.1 V 1
Output GND Output GND Output GND 2
DO NOT ONNE T DO NOT ONNE T DO NOT ONNE T 3
Pow er Supply GND Pow er Supply GND Pow er Supply GND 4
Pow er Supply + Pow er Supply + Pow er Supply + 5
4...20 mA

MAGNETIC CURSOR
Order Code A B C D
P UR022 32.8 13.5 23.9 -
P UR023 32.8 13.5 23.9 11.0
P UR024 25.4 13.5 - -
P UR026 f or liquids 52.4 12.0 44.0 -
P UR027 f or liquids 52.4 15.0 44.0 -
Note:
P UR026 and P UR027 are supplied with kit PKIT036 for floating cursor for liquids.
Material P UR026, P UR027: stainless steel AISI 316
Please order magnetic cursor
separately (not included in the
delivery of the sensor).
P UR022 P UR023 P UR024 P UR026/027
TECHNICAL DATA
Electrical stroke ( .E.) [mm] Measurement range
Linearity < ±0.02 (min. ±0.06 mm)
MSB...F1 total length L [mm] Measurement range + 131.5 (excluding cable)
MSB...F2 total length L [mm] Measurement range + 140.3 (excluding connector)
Repeatability [mm] < 0.01
Hy steresis < ±0.005 %
Sampling time MR 50 to 1000: 1 / MR 1100 to 2000: 1.5 / MR > 2000: 2
MR: Measurement range
[msec]

DECLARATION OF EC-CONFORMITY
ACCESSORIES MSB...F2
K5P2M-S-M12
K5P5M-S-M12
K5P10M-S-M12
K5P2M-SW-M12
K5P5M-SW-M12
K5P10M-SW-M12
Connection cable analo output, 5-pole, s hielded
2 m, connector, straight
5 m, connector, straight
10 m, connector, straight
2 m, connector, angular
5 m, connector, angular
10 m, connector, angular
PIN Cable colour K5P..
1 brow n
2 w hite
3 blue
4 black
5 grey
Way on Positionsmesstechnik GmbH
Mehlbeerenstrasse 4
82024 Taufkirchen / Germany
This is to certify that the products
lassification Magnetostrictive Sensors
Series MSB
fulfill the current request of the following E -directives:
EMV-directive 2004/108/EU (until April 19th, 2016)
2014/30/EU (from April 20th, 2016)
applied harmonized standards:
EN 61000-6-2:2005, EN 61000-6-4:2007, EN 61326-1:2006
The declaration of conformity loses its validity if the product is misused or modified without proper
authorisation.
Taufkirchen, 24.02.2016 Andreas Täger, EO