Webasto Thermo Call TC2 COMFORT User manual

Dear Webasto customer,
Thank you for purchasing a new Webasto original accessory.
This product provides you with a comfortable and innovative operating option for your
Webasto auxiliary heating. This operating manual supplements the information you
received from the Webasto workshop or servicestation and covers all the functions of the
Thermo Call TC2.
With the Thermo Call TC2 CONNECT you can use SMS (Short Message Service) for
remote control of your Webasto auxiliary heating system. All mobile phones which permit
the sending of SMS texts are suitable for use as control units. You can not only switch on
your Webasto auxiliary heating system but you can also program the operating time
according to your requirements.
NOTES:
• Always observe the general operating manual for the Webasto auxiliary heating
and the location of your vehicle before activating the TC2 CONNECT.
• In heating mode, the heating must be set to "warm" before the vehicle is left.
Thevehicleblower must be setto heatingmode (for a3-levelbloweron the 1stlevel
and for a 4-level blower on the 2nd level).
Set it to at least 1/3 of the maximum on infinitely variable blowers,
• We recommend setting the heating time to correspond with the travelling time for
Thermo Top E/C and Therma Top P heating devices in order to prevent the battery
discharging. For a travel time of approx. 30 minutes (one way), we recommend to
set the operating period to 30 minutes.
It is possible to program the operating period up to 120 minutes on air heaters and
truck or bus water heaters.
Thermo Call TC2 is factory set to a 30 minute period of heating.
General information
Use
Operating manual
Thermo Call TC2 CONNECT Webasto AG
Postfach 80 D-82132 Stockdorf
Hotline [phone],
Hotfax [phone]
http://www.webasto.com
Ident-Nr. 9014675B 02/2008

• You will have been assigned a separate Thermo Call telephone number by your
telephone carrier.
• Your personal password may be between2 and 10 characters in length and consist
of both numbers and letters. You can choose it yourself as wished. The password
is factory set to "00“.
• An SMS command to the Webasto auxiliary heating system must ALWAYS have
the following structure: PASSWORD COMMAND (e.g.: "00 ON“ – The auxiliary
heating system is now activated)
IMPORTANT: please make sure that there is a space between your password and
the next command.
• If an SMS command is sent with an incorrect password, you will receive the
message "Password ERROR“.
• If the SMS command is sent with an incorrect command, you will receive the
message "Command ERROR“.
• If an SMS command cannot be executed, you will receive the message
"FAIL x..x“ with x..x standing for the SMS command that failed.
Operation via Mobile Telephone

A push-button is included in the delivery. This must be installed if you have no preset timer
or Telestart and is used to activate and display the current operating mode of your
auxiliary heating.
Pressing the button repeats the last control function. If the system is activated by pressing
the button, the current heating or ventilation cycle ends.
Function Command
Press Key No. Note
My Thermo Call TC2 telephone number:
ACTIVATE auxiliary heating ON 1
DE-ACTIVATE auxiliary heating OFF 2
ACTIVATE auxiliary heating system for xxx minutes ON (Number of
minutes) 3
PROGRAMMING operating time TIME (Number of
minutes) 4
Change PASSWORD PWD ….. 5
Activate SMS RESPONSE SMS ON 6
De-activate SMS RESPONSE SMS OFF 6
Status check CHECK 7
LED steady light →Auxiliary heating active
LED blinks fast →Immediately after button is pressed
SMS Syntax: PASSWORD COMMAND (example:00 ON toswitch
on the auxiliary heating system where the password is "00")
Operation via push-button Switch

1 The auxiliary heating system is activated for the preprogrammed heating
time.
2 The auxiliary heating system is switched off.
3
The auxiliary heating system is switched on for the required number of
minutes without the value of the preprogrammed heating time being
changed. Here the value must lie between 10 and 120. A value <10 will be
identified as 10, and a value of >120 as 120.
4 The operating time is stored in the system and must lie between 10 and 120.
A value of <10 will be identified as 10, and a value of >120 as 120.
5
For".....“pleaseenteryournew password. This mayconsist of bothnumbers
and letters. The passwordlength can be between 2 and 10 characters. If the
new password is accepted, you will receive an SMS conformation message
stating "Password ...... OK“
6 You can suppress the SMS confirmation message if wished.
7
Response options: WEBASTO; yyy = Remaining heating time
“ Webasto ON CLOCK” (Your auxiliary heating system has been
activated via the timer)
or
“ Webasto ON yyy min” (Your auxiliary heating system has been
activated via the button or SMS text
or
“ WEBASTO OFF” (Your auxiliary heating system has been
switched off)
Note Comment