Weider WESY29520 User manual

USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual be ore using
this equipment. Save this manual
or uture re erence.
Model No. WESY29520
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
Visit our website at
www.weider itness.com
new products, prizes,
fitness tips, and much more!
QUESTIONS?
As a manu acturer, we are
committed to providing com-
plete customer satis action. I
you have questions, or i there
are missing parts, we will guar-
antee complete satis action
through direct assistance rom
our actory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, ree o
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST

2
IMPOR AN PRECAU IONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUS MEN S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
WEIGH RESIS ANCE CHAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMEN PAR S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
FULL 90 DAY WARRAN Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PAR IDEN IFICA ION CHAR and a PAR LIS /EXPLODED DRAWING are attached in the center of
this manual. Remove the PAR IDEN IFICA ION CHAR and the PAR LIS /EXPLODED DRAWING before
beginning assembly.
TABLE OF CONTENTS
WEIDER is a registered trademark of ICON Health & Fitness, Inc.

3
1. Read all instructions in this manual and in
the accompanying literature be ore using the
weight system. Use the weight system only
as described in this manual.
2. It is the responsibility o the owner to ensure
that all users o the weight system are ade-
quately in ormed o all precautions.
3. The weight system is intended or home use
only. Do not use the weight system in a com-
mercial, rental, or institutional setting.
4. Use the weight system only on a level sur-
ace. Cover the loor or carpet beneath the
weight system to protect the loor.
5. Make sure all parts are properly tightened
each time the weight system is used.
Replace any worn parts immediately.
6. Keep children under the age o 12 and pets
away rom the weight system at all times.
7. Keep hands and eet away rom moving parts.
8. Always wear athletic shoes or oot protec-
tion when using the weight system.
9. The weight system is designed to support a
maximum user weight o 300 pounds.
10. Never release the press arm, butter ly arms,
leg lever, leg press base, lat bar, ab strap, or
handle while weights are raised; the weights
will all with great orce.
11. Make sure that the cables remain on the pul-
leys at all times. I the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all o the pulleys.
12. Always stand on the oot plate when per-
orming an exercise that could cause the
weight system to tip.
13. Always disconnect the lat bar from the
weight system when performing an exercise
that does not use the lat bar.
14. I you eel pain or dizziness while exercising,
stop immediately and begin cooling down.
15. The decals shown
below have been
placed on the weight
system in the locations
shown on page 4. I a
decal is missing or
illegible, call our toll-
ree Customer Hot Line
at 1-800-999-3756 and
order a ree replace-
ment decal. Apply the
decal in the location
shown.
WARNING:To reduce the risk o serious injury, read the ollowing important precau-
tions be ore using the weight system.
WARNING:Be ore beginning this or any exercise program, consult your physician. This
is especially important or persons over the age o 35 or persons with pre-existing health problems.
Read all instructions be ore using. ICON assumes no responsibility or personal injury or property
damage sustained by or through the use o this product.
Keep hands and
fingers clear of
this area.
IMPORTANT PRECAUTIONS
Decal 1
Decal 2

4
BEFORE YOU BEGIN
ASSEMBLED
DIMENSIONS:
Height: 77 in.
Width: 81 in.
Length: 59 in.
Foot Plate
Low Pulley
Station
Ab Pulley Station
High Pulley Station
Lat Bar
Leg Lever
Butterfly Arm
Press Arm
Weight
Seat
Seat
Backrest
Backrest
Leg Press
Plate
hank you for selecting the versatile WEIDER®PRO
3200 weight system. he PRO 3200 weight system
offers a selection of weight stations designed to devel-
op every major muscle group of the body. Whether
your goal is to tone your body, build dramatic muscle
size and strength, or improve your cardiovascular sys-
tem, the weight system will help you to achieve the
results you want.
For your bene it, read this manual care ully be ore
using the weight system. If you have questions after
reading this manual, please call our Customer Service
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain ime
(excluding holidays). o help us assist you, please
note the product model number and serial number
before calling. he model number is WESY29520. he
serial number can be found on a decal attached to the
weight system (see the front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Warning
Decal 1
Warning Decal 2
(One on each side
of the right upright.)
Note: The terms “right side” and “le t side” are determined rel-
ative to a person acing away rom the weight system; they do
not correspond to right and le t in the pictures in the manual.
Right Side
Le t Side

26
5
Be ore beginning assembly, care ully read the
ollowing in ormation and instructions:
•Assembly requires two people.
•Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
•ighten all parts as you assemble them, unless
instructed to do otherwise.
•As you assemble the weight system, make sure
all parts are oriented as shown in the drawings.
•For help identifying small parts, use the PART
DENT F CAT ON CHART.
An Allen wrench (included) and the ollowing
tools (not included) are required or assembly:
• two adjustable wrenches
• one rubber mallet
• one standard screwdriver
• one Phillips screwdriver
• lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Make Things Easier or Yoursel
Everything in this manual is designed to ensure
that the weight system can be assembled suc-
cessfully by anyone. However, it is important to
realize that the versatile weight system has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.
ASSEMBLY
1
33
33
60
67
68
98
1
71
60
67
28
26
26
57
57
1. Be ore beginning, make sure that you under-
stand the in ormation in the box above.
Attach the Base Cap (28) to the Right Base (1)
with two #8 x 3/4” Screws (68).
Attach the Center Base (67) to the Right Base (1)
with two 5/16” x 2 3/4” Bolts (60), two 5/16”
Washers (26), and two 5/16” Nylon Locknuts (71).
Insert four 5/16” x 2 1/2” Carriage Bolts (57) up
into the Right Base (1). Tape the bolt heads in
place.
FRAME ASSEMBLY
2. Press two 2” Square Inner Caps (33) into the
ends of the Left Base (2). Attach the Rubber
Bumper (98) to the Left Base with a #8 x 3/4”
Screw (68).
Insert four 5/16” x 2 1/2” Carriage Bolts (57) up
into the Left Base (2). Tape the bolt heads in
place.
Attach the Left Base (2) to the Right Base (1) and
the Center Base (67) with three 5/16” x 2 3/4”
Bolts (60), three 5/16” Washers (26), and three
5/16” Nylon Locknuts (71).
2
1
2
60
71
57
68
26
57

6
4. Press a 2” x 2 1/2” Inner Cap (22) into the top of
the Right Leg (73). Press a 1 1/2” Square Inner
Cap (41) into the Right Upright (6).
Attach the Right Upright (6) to the Right Base (1)
with the two indicated 5/16” x 2 1/2” Carriage
Bolts (57) and two 5/16” Nylon Locknuts (71).
Attach the Bumper (25) to the Right Leg (73) with
the #10 x 1” Screw (77).
Attach the Right Leg (73) to the Right Base (1)
with the two indicated 5/16” x 2 1/2” Carriage
Bolts (57) and two 5/16” Nylon Locknuts (71).
Do not tighten the 5/16” Nylon Locknuts (71)
yet.
3. Attach the Base Plate (37) to the Left Base (2)
with a 3/8” x 5 1/2” Bolt (58) and a 3/8” Nylon
Locknut (70).
Attach the Left Upright (7) to the Left Base (2)
with the two indicated 5/16” x 2 1/2” Carriage
Bolts (57) and two 5/16” Nylon Locknuts (71).
Attach the Left Leg (36) to the Left Base (2) with
the two indicated 5/16” x 2 1/2” Carriage Bolts
(57) and two 5/16” Nylon Locknuts (71). Be sure
the large upper hole in the Le t Leg is on the
side shown.
Do not tighten the 5/16” Nylon Locknuts (71)
yet.
3
4
2
57
71
25
77
6
1
73
41
22
36
Large
Hole
7
71
57
57 37
70
58
71
71
71
71
71 71
57

7
7. Set two Weight Bumpers (83) over the indicated
holes in the Center Base (67). Insert the two
Weight Guides (20) into the holes. Attach the
Weight Guides to the Center Base with two 5/16”
x 2 3/4” Bolts (60), four 5/16” Washers (26), and
two 5/16” Nylon Locknuts (71).
26
26
26
26
73
71
6
5
59
59 71
5
71 71
83 83
26
26
26
60
26
67
20
7
6. Press a 2” Square Inner Cap (33) into the end of
the Left Seat Frame (29).
Orient the Left Seat Frame (29) with the Large
Hole facing the direction shown. Attach the Left
Seat Frame to the Left Leg (36) with two 5/16” x 2
1/2” Carriage Bolts (57) and two 5/16” Nylon
Locknuts (71).
Attach the Left Seat Frame (29) to the Left Upright
(7) with two 5/16” x 3 1/4” Bolts (59), two 5/16”
Washers (26), and two 5/16” Nylon Locknuts (71).
Do not tighten the 5/16” Nylon Locknuts (71)
yet.
33
26
26
36
71 71
59
29
Large
Hole
59
7
71
6
57
5. Orient the Right Seat Frame (5) so the indicated
holes are in the positions shown. Attach the Right
Seat Frame to the Right Leg (73) with two 5/16” x
3 1/4” Bolts (59), two 5/16” Washers (26), and
two 5/16” Nylon Locknuts (71).
Attach the Right Seat Frame (5) to the Right
Upright (6) with two 5/16” x 3 1/4” Bolts (59), two
5/16” Washers (26), and two 5/16” Nylon
Locknuts (71).
Do not tighten the 5/16” Nylon Locknuts (71)
yet.
Hole
Large
Hole

8
10. Press a 2” x 2 1/2” Inner Cap (22) into the end of
the Right op Frame (8).
Attach the Right op Frame (8) to the Right
Upright (6) with two 5/16” x 3 1/4” Bolts (59), a
Support Plate (21), and two 5/16” Nylon Locknuts
(71).
Attach the Right op Frame (8) to the Left op
Frame (3) with two 5/16” x 2 3/4” Bolts (60), two
5/16” Washers (26), and two 5/16” Nylon
Locknuts (71).
Do not tighten the 5/16” Nylon Locknuts (71)
yet.
9. Press two 2” x 2 1/2” Inner Caps (22) into the
ends of the Left op Frame (3).
Attach the Left op Frame (3) to the Left Upright
(7) with two 5/16” x 3 1/4” Bolts (59), a Support
Plate (21), and two 5/16” Nylon Locknuts (71). Do
not tighten the Locknuts yet.
8. Slide the eight Weights (72) onto the Weight
Guides (20) with the pin grooves on the side
shown.
Press the Weight ube Bumper (32) into the bot-
tom of the Weight ube (82). Insert the Weight
ube into the center hole in the stack of Weights
(72). Be sure the Weight Tube is oriented as
shown.
Lubricate the indicated holes in the op Weight
(74). Slide the op Weight onto the Weight
Guides (20), with the pin groove on the bottom.
72
32
74
20
82
8Lubricate
Pin
Groove
Holes
22
71
71
59
321
22
7
9
6
59
22
71 71
71
3
26 60
8
21
10

9
13. Lubricate a 3/8” x 2” Bolt (62) with grease. Attach
the Pivot Bracket (48) to the Right Butterfly Arm
(11) with the Bolt and a 3/8” Nylon Jamnut (50).
Do not overtighten the Locknut; the Pivot
Bracket must be able to pivot easily.
Press a 1 1/2” x 2” Inner Cap (23) into the indicat-
ed end of the Right Butterfly Arm (11). Wet the
bottom end of the Arm with soapy water. Slide a
Large Foam Pad (19) onto the Arm.
Slide a Foam Grip (76) onto a Press Handle (12).
Press a 1” Round Inner Cap (24) into the end of
the Handle. Attach the Handle to the Right
Butterfly Arm (11) with two 5/16” x 3/4” Button
Head Bolts (64).
Slide the Large Foam Pad (19) down so that the
bottom of the Foam Pad is even with the bottom
of the Right Butterfly Arm (11).
Repeat this step with the Le t Butter ly Arm
(10).
11. Press the two Weight Guide Bushings (44) into
the Center op Frame (14). Slide the Center op
Frame onto the Weight Guides (20).
Attach the Center op Frame (14) to the Right
op Frame (8) with two 5/16” x 2 3/4” Bolts (60),
two 5/16” Washers (26), and two 5/16” Nylon
Locknuts (71).
Attach the Center op Frame (14) to the Left op
Frame (3) with two 5/16” x 2 3/4” Bolts (60), two
5/16” Washers (26), and two 5/16” Nylon
Locknuts (71).
Tighten all o the 5/16” Nylon Locknuts (71)
used in steps 3–11.
26 26
26
71
71
14
8
3
44
20
60
60 71
71
11
22
70
8
9
61
68
53
53
Lubricate
12
64
64
76
19 10
12
11 50
48
62
24
23
13
12. Press a 2” x 2 1/2” Inner Cap (22) into the
Butterfly Frame (9).
Insert the two Locking Pins (53) into the Butterfly
Frame (9). Attach the tether on the Pins to the
Butterfly Frame with a #8 x 3/4” Screw (68). Do
not fully tighten the Screw.
Lubricate a 3/8” x 3” Bolt (61) with grease. Attach
the Butterfly Frame (9) to the Right op Frame (8)
with the Bolt and a 3/8” Nylon Locknut (70). Do
not overtighten the Locknut; the Butter ly
Frame must be able to pivot easily.
ARM ASSEMBLY
Lubricate

10
16. Press a 2” x 2 1/2” Inner Cap (22) into the top of
the Leg Press Frame (30).
Lubricate a 3/8” x 3” Bolt (61) with grease. Attach
the Leg Press Frame (30) to the Left Base (2)
with the Bolt and a 3/8” Nylon Locknut (70). Do
not overtighten the Locknut; the Leg Press
Frame must be able to pivot easily.
14. Lubricate a 3/8” x 3” Button Head Bolt (97) and
both sides of two Plastic Washers (55) with
grease. Attach the Right Butterfly Arm (11) to the
Butterfly Frame (9) with the Bolt, the two Plastic
Washers, two Butterfly Caps (54), two 3/8”
Washers (75), and a 3/8” Nylon Jamnut (50). Do
not overtighten the Jamnut; the Butter ly Arm
must be able to pivot easily. Be sure the
indented sides o the Plastic Washers it over
the welded bushing in the Butter ly Arm.
Repeat this step with the Le t Butter ly Arm
(10).
910
11
97
54
54
55
55
Lubricate
Welded
Bushing
Lubricate
75
75
50
14
23 Lubricate
23
63
50
4
73
15
2
22
70
61
30
16
15. Press two 1 1/2” x 2” Inner Caps (23) into the
ends of the Leg Lever (4).
Lubricate a 3/8” x 2 1/2” Bolt (63) with grease.
Attach the Leg Lever (4) to the Right Leg (73)
with the Bolt and a 3/8” Nylon Jamnut (50). Do
not overtighten the Jamnut; the Leg Lever
must be able to pivot easily.
Lubricate

11
20. Note: The ollowing drawings are shown rom
the le t side o the weight system, with the
Le t Top Frame (3) removed or clarity.
Wrap the High Cable (45) around a 3 1/2” Pulley
(38). Attach the Pulley at the rear hole, inside of
the bracket on the Center op Frame (14) with a
3/8” x 1 3/4” Bolt (66) and a 3/8” Nylon Locknut
(70).
17.
Locate the High Cable (45). Route the Cable up
through the Left op Frame (3) and around a
3 1/2” Pulley (38). Attach the Pulley inside the op
Frame with a 3/8” x 2 3/4” Bolt (81), two 3/8”
Washers (75), two 1/2” Spacers (34), and a 3/8”
Nylon Locknut (70).
18. Route the High Cable (45) around a 3 1/2” Pulley
(38) and down through the Left op Frame (3).
Attach the Pulley and a Cable rap (91) inside
the op Frame with a 3/8” x 2 3/4” Bolt (81), two
3/8” Washers (75), two 1/2” Spacers (34), and a
3/8” Nylon Locknut (70). Be sure the Cable Trap
is turned to hold the Cable in the groove o
the Pulley.
Note: To complete this step, it may be neces-
sary to loosen the our indicated 5/16” Nylon
Locknuts (71). Retighten the Locknuts when
this step is completed.
19. Remove the preassembled 3 1/2” Pulleys (38)
rom an Adjustable Double “U”-Bracket (56).
Wrap the High Cable (45) around a 3 1/2” Pulley
(38). Attach the Pulley to the single hole side of
the Adjustable Double “U”-Bracket (56) with a
3/8” x 2” Bolt (62) and a 3/8” Nylon Locknut (70).
38
45
75
70
81 75
34
3
34
17
3
34
75
34
75
81
38
70
71
91
45
18
70
56
38
62
45
19
38
66
70
45
14
20
CABLE ASSEMBLY
IMPORTANT: Re er to the CABLE
DIAGRAMS and the CABLE ID CHART on
pages 24 and 25 or help identi ying and
routing the cables. While assembling the
cables, do not overtighten the locknuts
attaching the pulleys; the pulleys must be
able to turn reely.

12
23. Locate the Leg Press Cable (95). Attach the
Cable inside the Left Leg (36) with a 3/8” x 2 3/4”
Bolt (81), two 3/8” Washers (75), two Long
Spacers (80), and a 3/8” Nylon Locknut (70).
24. Wrap the Leg Press Cable (95) around a 3 1/2”
Pulley (38). Attach the Pulley inside the Leg
Press Frame (30) with a 3/8” x 2 3/4” Bolt (81),
two 3/8” Washers (75), two 1/2” Spacers (34),
and a 3/8” Nylon Locknut (70).
22. Attach the end of the High Cable (45) to the
Small “U”-Bracket (79) with a 1/4” Washer (35)
and a 1/4” Nylon Locknut (65). Note: Do not
completely tighten the Nylon Locknut; it
should be threaded only two turns onto the
end o the Cable, as shown in the inset draw-
ing.
Attach the Small “U”-Bracket (79) to the Weight
ube (82) with a 5/16” x 1 3/4” Bolt (69) and a
5/16” Nylon Locknut (71). Do not overtighten
the Locknut; the Weight Tube should be able
to pivot in the “U”-Bracket.
21. Wrap the High Cable (45) around a 3 1/2” Pulley
(38). Attach the Pulley at the forward hole, inside
of the bracket on the Center op Frame (14) with
a 3/8” x 1 3/4” Bolt (66) and a 3/8” Nylon Locknut
(70).
38 45
14
70
66
21
82
69 65
35
45
79 71
22
81 80 80
70
75 36
75
95
34
34
75
75
70
95
81
30
38
23
24
45
65

13
27. Remove the preattached 3 1/2” Pulley (not
shown) rom the “U”-Bracket (85).
Attach the end of the Leg Press Cable (95) to the
“U”-Bracket (85) with a 1/4” Washer (35) and a
1/4” Nylon Locknut (65). Note: Do not complete-
ly tighten the Locknut; it should be threaded
only two turns onto the end o the Cable, as
shown in the inset drawing.
28. Locate the Butter ly Cable (46). Attach the
Cable to the Pivot Bracket (48) on the Left
Butterfly Arm (10) with an 5/16” x 1” Shoulder Bolt
(78) and a 5/16” Nylon Locknut (71).
26. Wrap the Leg Press Cable (95) around a 3 1/2”
Pulley (38). Attach the Pulley inside the bracket
on the Left op Frame (3) with a 3/8” x 2” Bolt
(62) and a 3/8” Nylon Locknut (70).
25. Route the Leg Press Cable (95) through the Left
Leg (36) and the Left Upright (7) as shown. Wrap
the Cable around a 3 1/2” Pulley (38). Attach the
Pulley inside the Upright with a 3/8” x 2 3/4” Bolt
(81), two 3/8” Washers (75), two 1/2” Spacers
(34), and a 3/8” Nylon Locknut (70).
95
70
75
75
38
81
7
36
34
34
25
3
70
95
38
62
26
95
65
85 65
95
35
27
28
10
46
48
71
78

14
31. Wrap the Butterfly Cable (46) around a “V”-Pulley
(39). Attach the Pulley and a Long Cable rap
(40) to the bracket on the Right Upright (6) with a
3/8” x 2 1/2” Bolt (63) and a 3/8” Nylon Locknut
(70). Be sure the Cable Trap is turned to hold
the Cable in the groove o the Pulley.
32. Attach the Butterfly Cable (46) to the Pivot
Bracket (48) on the Right Butterfly Arm (11) with a
5/16” x 1” Shoulder Bolt (78) and an 5/16” Nylon
Locknut (71).
29. Wrap the Butterfly Cable (46) around a “V”-Pulley
(39). Attach the Pulley and a Long Cable rap
(40) to the bracket on the Right Upright (6) with a
3/8” x 2 1/2” Bolt (63) and a 3/8” Nylon Locknut
(70). Be sure the Cable Trap is turned to hold
the Cable in the groove o the Pulley.
30. Remove the preattached 3 1/2” Pulleys (38)
rom the Double “U”-Bracket (102).
Wrap the Butterfly Cable (46) around a 3 1/2”
Pulley (38). Attach the Pulley to the Double “U”-
Bracket (102) with a 3/8” x 2” Bolt (62) and a 3/8”
Nylon Locknut (70).
63
46
40
70
6
39
29
62
70
38
102
46
30
6
39
46
63
70
40
31
46
71
11
78
48
32

15
35. Route the Leg Lever Cable (96) through the Right
Upright (6) and around a 3 1/2” Pulley (38).
Attach the Pulley and a Cable rap (91) to the
Upright with a 3/8” x 3 3/4” Bolt (84), a 3/8”
Washer (75), and a 3/8” Nylon Locknut (70).
36. Wrap the Leg Lever Cable (96) around a 3 1/2”
Pulley (38). Attach the Pulley to the Double “U”-
Bracket (102) with a 3/8” x 2” Bolt (62) and a 3/8”
Nylon Locknut (70). Be sure the Cable Trap is
turned to hold the Cable in the groove o the
Pulley.
34. Attach a 3 1/2” Pulley (38) inside the Right Leg
(73) with a 3/8” x 2 3/4” Bolt (81), two 3/8”
Washers (75), two 1/2” Spacers (34), and a 3/8”
Nylon Locknut (70).
33. Locate the Leg Lever Cable (96). Route the
eyelet end of the Cable through the Right Leg
(73) and attach it to the Leg Lever (4) with a 5/16”
x 1” Shoulder Bolt (78) and a 5/16” Nylon Locknut
(71).
73
4
71
78
96
33
34
34 81
73 38
75
75
70
34
91
96
6
70
84
38
35
96
62
38
102
70
36
75

16
39. Route the Low Cable (47) through the Left Leg
(36) and the Left Upright (7). Attach a 3 1/2”
Pulley (38) inside the Upright with a 3/8” x 2 3/4”
Bolt (81), two 3/8” Washers (75), two 1/2”
Spacers (34), and a 3/8” Nylon Locknut (70).
40. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley and a Cable rap (91) to
the lower set of holes in the indicated “U”-Bracket
(85) with a 3/8” x 2” Bolt (62) and a 3/8” Nylon
Locknut (70). Be sure the Cable Trap is turned
to hold the Cable in the groove o the Pulley.
38. Locate the Low Cable (47). Route the small ball
on the Cable through the cage on the Leg Press
Frame (30).
Attach a 3 1/2” Pulley (38) inside the Leg Press
Frame (30) with a 3/8” x 2 3/4” Bolt (81), two 3/8”
Washers (75), two 1/2” Spacers (34), and a 3/8”
Nylon Locknut (70).
37. Remove the preattached 3 1/2” Pulley (not
shown) rom the “U”-Bracket (85).
Attach the end of the Leg Lever Cable (96) to the
other “U”-Bracket (85) with a 1/4” Washer (35)
and a 1/4” Nylon Locknut (65). Note: Do not
completely tighten the Nylon Locknut; it
should be threaded only two turns onto the
end o the Cable, as shown in the inset draw-
ing.
65
35
85
96
37
30
70
75
Cage
47
81
38 34
34
38
34
34
75
75
70
7
36
38
47
81
39
38 47
91
85
70
62
40
96
65
75

17
41. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley to the indicated bracket on
the Left Base (2) with a 3/8” x 2” Bolt (62) and a
3/8” Nylon Locknut (70).
43. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley and a Cable rap (91) to
the second set of holes from the bottom of the
indicated Adjustable Double “U”-Bracket (56) with
a 3/8” x 2” Bolt (62) and a 3/8” Nylon Locknut
(70). Be sure the Cable Trap is turned to hold
the Cable in the groove o the Pulley.
44. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley to the indicated bracket on
the Right Base (1) with a 3/8” x 2” Bolt (62) and a
3/8” Nylon Locknut (70).
42. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley to the indicated bracket on
the Left Base (2) with a 3/8” x 2” Bolt (62) and a
3/8” Nylon Locknut (70).
62
70
2
38
47
41
62 70
2
38
47
42
56
70
91
62
38 47
43
62
70
1
38
47
44

18
45. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley to the indicated bracket on
the Right Base (1) with a 3/8” x 2” Bolt (62) and a
3/8” Nylon Locknut (70).
47. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley and a Cable rap (91) to
the side of the Right Upright (6) with a 3/8” x
3 3/4” Bolt (84), a 3/8” Washer (75), and a 3/8”
Nylon Locknut (70). Be sure the Cable Trap is
turned to hold the Cable in the groove o the
Pulley.
48. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley and a pair of Pulley
Covers (92) to the Right Upright (6) with a 3/8” x
3 3/4” Bolt (84), two 3/8” Washers (75), and a 3/8”
Nylon Jamnut (50). Be sure the small tabs on
the Pulley Covers are on the side shown, and
the Cable is between the Pulley and the rod
on the Upright.
46. Wrap the Low Cable (47) around a 3 1/2” Pulley
(38). Attach the Pulley and a Cable rap (91) to
the lower set of holes in the indicated “U”-Bracket
(85) with a 3/8” x 2” Bolt (62) and a 3/8” Nylon
Locknut (70). Be sure the Cable Trap is turned
to hold the Cable in the groove o the Pulley.
62
70
1
38
47
45
62
70
91 85
38 47
46
84
70
91
75
6
38
47
47
75 50
75
Small
abs
92
92
6
84
38
47
48

19
50. Press two 3/4” x 1 1/2” Inner Caps (103) and a
1 1/4” Square Inner Cap (104) into the Adjustable
Backrest Frame (100).
Attach a Backrest (15) to the Adjustable Backrest
Frame (100) with four 1/4” x 3/4” Bolts (13).
Insert the Adjustable Backrest Frame (100) into
the Right Upright (6) and secure it with an
Adjustment Knob (101).
Attach the other Backrest (15) and the Le t
Upright (not shown) with our 1/4” x 3/4” Bolts
(13).
51. Slide the Long Pad ube (17) through the hole in
the Right Leg (73). Slide two Foam Pads (18)
onto the ends of the Pad ube. Press two 3/4”
Round Inner Caps (27) into the ends of the Pad
ube.
Repeat this step with the Short Pad Tube (94)
and the Leg Lever (4).
52. Press a 2” x 2 1/2” Inner Cap (22) into the indicat-
ed end of the Adjustment ube (88).
Attach the Leg Press Plate (31) to the Adjustment
ube (88) with a 5/16” x 2 1/2” Bolt (89), two
5/16” Washers (26), and a 5/16” Nylon Locknut
(71).
Attach the Adjustment ube (88) to the Leg Press
Frame (30) with the Leg Press Pin (87). Be sure
the Pin is in the locked position around the
Leg Press Frame.
49. Press two 3/4” x 1 1/2” Inner Caps (103) and a
1 1/4” Square Inner Cap (104) into an Adjustable
Seat Frame (99).
Attach a Seat (16) to the Adjustable Seat Frame
(99) with two 1/4” x 3/4” Screws (13), a1/4” x 1
1/2” Screw (90), and a 1/4” Washer (35).
Insert the Adjustable Seat Frame (99) into the
Right Seat Frame (5) and secure it with an
Adjustment Knob (101).
Repeat this step with the other Seat (16) and
the Le t Seat Frame (not shown).
16
103
103
90
35
104
101
99
13 5
49
17
27
73
27
4
18
18
94
50
51
26
71
31
22
89
30
87
88 26
52
SEAT ASSEMBLY
101
104
103
100
103
6
15 13
13

his section explains how to adjust the weight system. See the EXERCISE GUIDELINES on page 26 for impor-
tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight system is used. Replace any worn parts immediate-
ly. he weight system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ATTACHING THE ACCESSORIES TO A PULLEY
STATION
Attach the Lat Bar (42) to the High Cable (45) with a
Cable Clip (52). For some exercises, the Chain (not
shown) should be attached between the Lat Bar and
the High Cable with two Cable Clips. Adjust the
length o the Chain between the Lat Bar and the
High Cable so the Lat Bar is in the correct start-
ing position or the exercise to be per ormed.
he Handle (not shown) and Ab Strap (not shown)
can be attached in the same manner. he acces-
sories can be attached to the Low Cable (not shown)
in the same manner.
52
45
42
ADJUSTMENTS
86
72
CHANGING THE WEIGHT SETTING
o change the weight setting of the weight stack,
insert the Weight Pin (86) under the desired Weight
(72). Be sure to insert the Weight Pin until the bent
end of the Weight Pin is touching the Weights, and
turn the bent end downward. he weight setting of the
weight stack can be changed from 6 pounds to 106
pounds, in increments of 12.5 pounds. Note: Due to
the cables and pulleys, the actual amount o
resistance at each exercise station may vary rom
the weight setting. Use the WEIGHT RESISTANCE
CHART on page 23 to ind the actual amount o
resistance at each weight station.
20
53. Make sure that all parts have been properly tightened. he use of all remaining parts will be explained in
ADJUS MEN S, below.
Before using the weight system, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: I
the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE
DIAGRAM on pages 24 and 25 o this manual or proper cable routing. I there is any slack in the
cables, you will need to remove it by tightening the cables; see TIGHTENING THE CABLES on page
22.