Wenger Conductor’s Chair User manual

Assembly Instructions
Conductor’s Chair
Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General .........................................2
Manufacturer .....................................2
Intended Use.....................................2
Warranty ........................................2
Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chair Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chair Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Swivel Lock Option ................................4
Seat Angle Option .................................4
Note: Please read and understand these instructions before assembling.
Note: If you need additional information, contact Wenger Corporation using the information below.
©Wenger Corporation 2019 Printed in USA 2019-05 Part #157C002-04
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp.com

2
Important User Information
General
Copyright © 2019 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's
personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions.
The manufacturer reserves the right to change this product at any time.
The information in this document is not intended to cover all possible conditions and situations that might occur.
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products. If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or [phone] worldwide.
Manufacturer
The Conductor’s Chair is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
wengercorp.com
Intended Use
· This product is intended for indoor use in normal ambient temperature and humidity
conditions — it must not be exposed to prolonged outside weather conditions.
· This product is intended to be assembled only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ve full years from date
of shipment. A full warranty statement is available upon request.
Hardware
1/4-20 x 1/2”
Capscrew
3
1/4”
Lock Washer
1
1/4-20 x 1”
Capscrew
2
Swivel Lock
(Optional)
4
Spacer
(Optional)
5
7/16” Open-end wrench required.

2. Attach the back rest to the bottom of the seat cushion
using four 1/4” lock washers (1) and 1/4-20 x 1” capscrews (2).
If installing the swivel lock option, see the next page.
3
Chair Assembly
1. Select the appropriate holes for the back rest placement.
Chair Options on following page.
Forward
(Percussionist)
Back
Rest
Seat
Cushion
1/4”
Lock Washers
(1)
1/4-20 x 1"
Capscrews
(2)
Rear
(Conductor)
Center
(String Bass)
Select Hole Set
3. Attach the seat assembly to the base using
four 1/4” lock washers (1) and 1/4-20 x 1/2” capscrews (3).
If installing the seat angle option,
see the next page.
Base
Seat
Assembly
1/4”
Lock Washers
(1)
1/4-20 x 1/2"
Capscrews
(3)

4
Chair Options
Swivel Lock Option
The swivel lock option prevents the seat from being
rotated side-to-side.
1. Separate the seat from the base.
2. Attach the swivel lock (4) to the front holes of the
back rest using the original fasteners.
Orient the swivel lock as shown.
3. Reattach the seat assembly to the base.
Swivel
Lock
(4)
Swivel lock
orientation
Seat Angle Option
The seat angle option tilts the seat forward.
1. Remove the rear two screws and washers
securing the swivel base to the seat bottom.
2. Install spacers (5) between the
seat bottom and at metal bars.
3. Reattach the two rear screws and washers.
Spacer
(5)
Spacers between
seat bottom and
metal bars
Front
holes
Separate
seat from
base
Rear
holes
Spacer
(5)