Weslo MOMENTUM ELLIPTICAL User manual

CAUTION
Read all precautions and
instructions in this manual before
using this equipment. Keep this
manual for future reference.
Model No. WLEL19917.0
Serial No.
Write the serial number in the space
above for reference.
USER’S MANUAL
weslo.com
Serial
Number
Decal
To register your product and
activate your warranty today,
go to my.weslo.com.
For service at any time, go to
wesloservice.com.
Or call 1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT
Please do not contact the store.
ACTIVATE YOUR
WARRANTY
CUSTOMER CARE

2
WARNING DECAL PLACEMENT
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS..................................................................3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO USE THE ELLIPTICAL ..............................................................14
HOW TO USE THE CONSOLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
MAINTENANCE AND TROUBLESHOOTING ....................................................18
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
EXERCISE GUIDELINES ....................................................................20
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
ORDERING REPLACEMENT PARTS .................................................. Back Cover
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
This drawing shows the location(s) of the warning decal(s).
If a decal is missing or illegible, see the front cover
of this manual and request a free replacement decal.
Apply the decal in the location shown. Note: The decal(s)
may not be shown at actual size.
WESLO is a registered trademark of ICON Health & Fitness, Inc.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
IMPORTANT PRECAUTIONS
1. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
3. The elliptical is not intended for use by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless they are given supervi-
sion or instruction about use of the elliptical
by someone responsible for their safety.
4. Use the elliptical only as described in this
manual.
5. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.
6. Keep the elliptical indoors, away from
moisture and dust. Do not put the elliptical in
a garage or covered patio, or near water.
7. Place the elliptical on a level surface, with a
mat beneath it to protect the floor or carpet.
Make sure that there is at least 2 ft. (0.6 m) of
clearance around the elliptical.
8. Inspect and properly tighten all parts each
time the elliptical is used. Replace any worn
parts immediately.
9. Keep children under age 13 and pets away
from the elliptical at all times.
10. The elliptical should not be used by persons
weighing more than 250 lbs. (113 kg).
11. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection.
12. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.
13. The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
14. The elliptical does not have a freewheel; the
pedals will continue to move until the fly-
wheel stops. Reduce your pedaling speed in
a controlled way.
15. Keep your back straight while using the ellip-
tical; do not arch your back.
16. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.

4
all
STANDARD SERVICE PLANS

5
BEFORE YOU BEGIN
Thank you for selecting the revolutionary WESLO®
MOMENTUM elliptical. The MOMENTUM elliptical
provides an impressive selection of features designed
to make your workouts at home more effective and
enjoyable.
For your benefit, read this manual carefully before
you use the elliptical. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Leveling Cap
Upper Arm
Resistance Knob
Console
Pulse Sensor
Pedal
Length: 3 ft. 10 in. (117 cm)
Width: 1 ft. 9 in. (53 cm)
Transport Wheel
Water Bottle Holder*
*Water bottle is not included

6
Left 1/2" x 110mm Bolt (78)–1
Right 1/2" x 110mm Bolt (70)–1
M8 x 65mm Carriage Bolt (73)–4 M10 x 45mm Bolt (76)–4
M8 Locknut
(84)–4
M8 Acorn Nut
(82)–4 Right 1/2" Nut
(85)–1
Left 1/2" Nut
(86)–1
M10 Locknut
(83)–4
M8 x 65mm Bolt (75)–4
M8 x 20mm Hex
Screw (77)–2
M8 x 16mm
Screw (74)–6
Pivot Washer
(67)–2
M13 Washer
(69)–2
M5 x 12mm
Screw (80)–2
M4 x 16mm
Flange Screw
(95)–2
M8 Split
Washer
(90)–12
M10 Washer
(72)–4
M13 Wave
Washer (58)–2
M8 Curved
Washer (65)–18
Pivot Wave
Washer (57)–2
PART IDENTIFICATION CHART
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it
has been preassembled. Extra parts may be included.

7
• To hire an authorized service technician to
assemble this product, call 1-800-445-2480.
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you nish assembly.
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
• To identify small parts, see page 6.
• In addition to the included tool(s), assembly
requires the following tools:
one Phillips screwdriver
one adjustable wrench
one pair of pliers
one rubber mallet
Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.
ASSEMBLY
1
2
2. Identify the Rear Stabilizer (4), which has
Leveling Caps (23).
Attach the Rear Stabilizer (4) to the Frame (1)
with two M8 x 65mm Carriage Bolts (73), two
M8 Curved Washers (65), and two M8 Acorn
Nuts (82); start both Carriage Bolts, and then
tighten the Acorn Nuts.
23 4
1
23
65
65
82
82
73
1. Go to my.weslo.com on your computer and
register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Care
• allows us to notify you of upgrades and offers
Note: If you do not have internet access, call
Customer Care (see the front cover of this
manual) and register your product.

8
3
4
3
73
65
65
82
82
1
3. Attach the Front Stabilizer (3) to the Frame (1)
with two M8 x 65mm Carriage Bolts (73), two
M8 Curved Washers (65), and two M8 Acorn
Nuts (82); start both Carriage Bolts, and then
tighten the Acorn Nuts.
4. While a second person holds the Upright (2)
near the Frame (1), connect the Upright Wire
(49) to the Reed Switch Wire (7).
Next, connect the Resistance Cable (20) to the
Lower Resistance Cable (21) in the following
way:
See drawing A. Pull upward on the metal
bracket (A) on the Lower Resistance Cable (21),
and insert the tip of the Resistance Cable (20)
into the wire clip inside the metal bracket.
See drawing B. Firmly pull the Resistance
Cable (20) upward and slide it into the top of the
metal bracket (A).
See drawing C. Using pliers, squeeze the
prongs on the upper end of the metal bracket (A)
together.
2
21
20
7
1
49
A
B
C
21
20
20
A
A
A

9
6
5. Insert the excess wire and cable into the
Frame (1).
Tip: Avoid pinching the wires and the cables.
Slide the Upright (2) onto the Frame (1).
Attach the Upright (2) with two M8 x 65mm Bolts
(75), four M8 Curved Washers (65), two M8 Split
Washers (90), and two M8 Locknuts (84); do not
fully tighten the Locknuts yet.
5
Avoid pinching
the wires and
the cables
2
2
1
75
84
84
90
90
65
65
75
65
65
75
65
84
65
90
90
65
65
75
84
6. Finish attaching the Upright (2) with two
M8 x 65mm Bolts (75), four M8 Curved Washers
(65), two M8 Split Washers (90), and two
M8 Locknuts (84); do not fully tighten the
Locknuts yet.

10
7
8. Identify the Right Lower Arm (11).
Using a plastic bag to keep your fingers clean,
apply a generous amount of the included grease
to the right axle on the Upright (2).
Next, orient a Spacer (46), a Pivot Wave
Washer (57), and the Right Lower Arm (11) as
shown and slide them onto the right axle on the
Upright (2).
Attach the Right Lower Arm (11) with an
M8 x 20mm Hex Screw (77), an M8 Split Washer
(90), and a Pivot Washer (67). Then, press a
Pivot Cap (39) firmly onto the Hex Screw.
Attach the Left Lower Arm (10) in the
same way.
Grease
8
7. Attach the Water Bottle Holder (41) to the
Upright (2) with two M4 x 16mm Flange Screws
(95); start both Flange Screws, and then
tighten them.
41
95
2
46
57
67
77
90
39
11
2
10