Weslo Boomerang 850 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manu-
al for future reference.
Model No. WLEVEL28840
Serial No.
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete cus-
tomer satisfaction. If you have
questions, or if there are missing
or damaged parts, please call:
Fax: [phone]
E-mail: serviciotecni-
[e-mail]
USERʼS MANUAL
Serial Number
Decal
0034 91 661 02 10
All manuals and user guides at all-guides.com
all-guides.com

TABLE OF CONTENTS
MPORTANTPRECAUTONS .................................................................3
BEFOREYOUBEGN .......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEELLPTCALCROSSTRANER ................................................9
MANTENANCEANDTROUBLESHOOTNG ....................................................12
CONDTONNGGUDELNES ...............................................................13
PARTLST ...............................................................................14
EXPLODEDDRAWNG .....................................................................15
HOWTOORDERREPLACEMENTPARTS..............................................BackCover
2
All manuals and user guides at all-guides.com

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical crosstrainer.
1. Read all instructions in this manual before
using the elliptical crosstrainer. Use the
elliptical crosstrainer only as described.
2. It is the responsibility of the owner to
ensure that all users of the elliptical
crosstrainer are adequately informed of all
precautions.
3. Place the elliptical crosstrainer on a level
surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical crosstrain-
er indoors, away from moisture and dust.
4. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
5. Keep children under 12 and pets away from
the elliptical crosstrainer at all times.
6. The elliptical crosstrainer should not be
used by persons weighing more than 115 kg
(250 lbs.).
7. Wear appropriate exercise clothing when
using the elliptical crosstrainer. Always wear
athletic shoes for foot protection.
8. Always hold the handlebars when mounting,
dismounting, or using the elliptical
crosstrainer.
9. Keep your back straight when using the
elliptical crosstrainer. Do not arch your
back.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
11. If you feel pain or dizziness at any time whilst
exercising, stop immediately and cool down.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. The elliptical crosstrainer is intended for
home use only. Do not use the elliptical
crosstrainer in a commercial, rental, or insti-
tutional setting.
14. A warning decal has been placed on the
elliptical crosstrainer in the location shown
below. Please note that the text on the decal
is in Spanish. Find the decal in English and
place it over the Spanish decal.
If the decal is missing, or if it is not legible,
please please call our Customer Service
Department and order a free replacement
decal (see the back cover of this manual).
Apply the decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
All manuals and user guides at all-guides.com

4
BEFORE YOU BEGIN
Congratulations for selecting the new BOOMERANG
850 elliptical crosstrainer. The BOOMERANG 850
elliptical crosstrainer is an incredibly smooth exerciser
that moves your feet in a natural elliptical path, mini-
mizing the impact on your knees and ankles. And the
unique BOOMERANG 850 features adjustable resis-
tance and a simple-to-use console to help you get the
most from your exercise.
For your benefit, read this manual carefully before
using the elliptical crosstrainer. f you have ques-
tions after reading this manual, please call our
Customer Service Department at 0034 91 661 02 10.
To help us assist you, please note the product model
number and serial number before calling. The model
number is WLEVEL28840. The serial number is found
on a decal attached to the elliptical crosstrainer (see
the front cover of this manual for the location of the
decal).
Before reading further, please familiarise yourself with
the parts that are labeled in the drawing below.
Handlebar
FRONT
BACK Pedal Arm
Pedal Disk
*No water bottle is included
Pedal
Console
Water Bottle Holder*
Pulse Sensor
Resistance Knob
Wheel
All manuals and user guides at all-guides.com

ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included hex keys, assembly requires a phillips screwdriver , an adjustable
spanner , and a rubber mallet .
As you assemble the elliptical crosstrainer, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing refers to the key number of the part, from the PART L ST on
page 14. The second number refers to the quantity used in assembly. Note: Some small parts may have been
pre-assembled for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.
5
M8
Washer (48)–4
M8 Split
Washer (59)–6
M8 Nylon
Locknut (38)–8 M10
Washer (35)–2
M4 x 16mm
Screw (42)–5
M10 x 25mm
Patch Screw (22)–2
M6 x 48mm Flat Head
Screw (36)–4
Pedal Arm Bolt Set (40)–2
M8 x 38mm Button Bolt (50)–4
M8 x 25mm Button
Screw (45)–1
M8 x 19mm Button
Screw (68)–6
M8 x 53mm Button Bolt (34)–4
1. dentify the Front Stabiliser (10), which is narrower than
the Rear Stabiliser (not shown). Whilst another person
lifts the front of the Frame (1), attach the Front
Stabiliser to the Frame with two M8 x 53mm Button
Bolts (34), two M8 Washers (48), and two M8 Nylon
Locknuts (38).
10
38
34
1
48
48
1
All manuals and user guides at all-guides.com

6
2. Whilst another person lifts the back of the Frame (1),
attach the Rear Stabiliser (28) to the Frame with two
M8 x 53mm Button Bolts (34), two M8 Washers (48),
and two M8 Nylon Locknuts (38).
34
28
48
48
1
2
38
3. nsert the Console Bracket (63) into the Upright (2) as
shown. Attach the Console Bracket to the Upright with
an M8 x 25mm Button Screw (45), two M8 Split
Washers (59), and two M8 x 19mm Button Screws
(68).
4. The Console (23) requires three 1.5V “AA” batteries;
alkaline batteries are recommended. nsert three bat-
teries into the battery compartment. Make sure that
the batteries are oriented as shown by the diagram
inside the battery compartment.
63
45
59
68
59
68
2
3
5. Have another person hold the Console (23) in the
position shown. nsert the control cable down through
the Upright (2). Connect the console wire to the Upper
Wire (44). Attach the ground wire to the Console
Bracket (63) with an M4 x 16mm Screw (42). Next,
insert the excess cable and wire down into the Upright.
Attach the Console (23) to the Console Bracket (63)
with four M4 x 16mm Screws (42). Be careful to
avoid pinching the cable and wires.
Make sure that the resistance knob is turned to the
lowest setting before continuing.
4
23
23
5
Batteries
63
42
2
42
Control Cable
Resistance
Knob
Console Wire
Ground
Wire
44
All manuals and user guides at all-guides.com
all-guides.com

50
38
7
7. dentify the Left Handlebar (6), which is marked with a
sticker. nsert the Left Handlebar into one of the
Handlebar Arms (5); make sure that the Handlebar
Arm is turned so the hexagonal holes are on the
indicated side. Attach the Left Handlebar to the
Handlebar Arm with two M8 x 38mm Button Bolts (50)
and two M8 Nylon Locknuts (38). Make sure that the
Nylon Locknuts are inside of the hexagonal holes.
Do not fully tighten the Button Bolts yet.
Apply a small amount of the included grease to the left
axle on the Upright (2).
Make sure that there are two Small Handlebar
Bushings (49) in the Left Handlebar (6). Slide a
Handlebar Spacer (47) and the Left Handlebar onto the
left axle on the Upright (2) as shown. Make sure that the
Handlebar Spacer is turned so the curved side is fac-
ing the Upright. Tap an Axle Cap (14) onto the axle.
Repeat this step to assemble the Right Handlebar (8)
and the other Handlebar Arm (5).
Grease
7
47
14
49
5
2
5
6
8
Hexagonal
Holes
6
1
2
68
68Make sure that
the wires and
cables do not
get pinched
and damaged
during this
step.
44
53
68
55
59
59
59
6. Whilst another person holds the Upright (2) near the
Frame (1), connect the Upper Wire (44) to the Reed
Switch Wire (53).
Next, connect the control cable to the Lower Cable
(55) in the following way:
• See drawing A. Pull up on the metal bracket on the
Lower Cable (55), and insert the tip of the control
cable into the wire clip inside of the metal bracket.
• See drawing B. Firmly pull the control cable and
slide it into the metal bracket on the Lower Cable
(55) as shown.
• See drawing C. Using pliers, squeeze together the
prongs on the upper end of the metal bracket.
Push the excess cable and wire down into the Frame
(1). Slide the Upright (2) onto the Frame. Be careful
not to pinch the wires or cables. Attach the Upright
with four M8 x 19mm Button Screws (68) and four M8
Split Washers (59). Do not tighten the Button
Screws yet.
55 55
Metal
Bracket
B
AC
55
Control
Cable
Control
Cable
Control
Cable
Control
Cable
All manuals and user guides at all-guides.com

8
10. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may
be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical crosstrainer.
9. Apply a small amount of grease to the axle on the left
Disc Crossbar (16). Slide the Left Pedal Arm (11) onto
the axle. Slide an M10 Washer (35) onto an M10 x
25mm Patch Screw (22), and tighten the Patch Screw
into the axle.
Next, hold the lower end of the left Handlebar Arm (5)
inside of the bracket on the Left Pedal Arm (11). Apply
grease to a Pedal Arm Bolt Set (40). Attach the Left
Pedal Arm to the left Handlebar Arm with the Bolt Set.
Do not overtighten the Bolt Set; the Handlebar Arm
must pivot freely.
Attach the Right Pedal Arm (12) to the right side of the
elliptical crosstrainer in the same way.
See step 5. Tighten the M8 x 19mm Button Screws (68)
in the Upright (2).
See step 6. Tighten the M8 x 38mm Button Bolts (50)
in the Handlebar Arms (5).
Grease
22 35
11
12
5
9
40
40
8
36
11
13
8. dentify the Left Pedal Arm (11). Attach a Pedal (13) to
the Left Pedal Arm with two M6 x 48mm Flat Head
Screws (36) as shown.
Attach the other Pedal to the Right Pedal Arm (not
shown) in the same way.
Grease
16
All manuals and user guides at all-guides.com

9
HOW TO USE THE ELLIPTICAL CROSSTRAINER
HOW TO EXERCISE ON THE ELLIPTICAL
CROSSTRAINER
To mount the elliptical crosstrainer, hold the handlebars
and step onto the pedal that is in the lowest position.
Then, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The pedal disks can turn in either direction. It is
recommended that you move the pedal disks in
the direction shown by the arrow; however, for
variety, you may turn the pedal disks in the oppo-
site direction.
To dismount the elliptical crosstrainer, wait until the
pedals come to a complete stop. Note: The elliptical
crosstrainer does not have a free wheel; the ped-
als will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.
HOW TO AD UST THE PEDALING RESISTANCE
As you exercise,
you can adjust the
resistance of the
pedals with the
resistance knob
on the console. To
increase the resis-
tance, turn the
knob clockwise; to
decrease the
resistance, turn the knob counterclockwise.
FEATURES OF THE CONSOLE
The easy-to-use console is designed to help you get
the most from your workouts. As you exercise, the
console will display the following modes:
Time—This mode displays the elapsed time (or the
time remaining in a pace program). Note: f you stop
pedalling, the time will begin to flash.
Distance—This mode displays the distance that you
have pedalled.
Calories—This mode displays the approximate number
of calories you have burned.
Fat calories—This mode displays the approximate
number of fat calories you have burned (see FAT
BURN NG on page 13).
Pulse—This mode displays your heart rate when you
use the pulse sensor.
Speed—This mode displays your pedalling speed.
Scan—When this mode is selected, the upper section
of the display will show both the speed mode and the
distance mode, and the lower left section of the display
will show both the calories mode and the fat calories
mode.
The console also offers four pace programs. Each pro-
gram automatically prompts you to increase or
decrease your pace as it guides you through an effec-
tive workout.
Pedal Disk
Pedal
Resistance
Knob
All manuals and user guides at all-guides.com

10
HOW TO USE THE MANUAL MODE
Turn on the console.
To turn on the console, press the On/Reset button
or begin pedalling. Note: f there is a sheet of clear
plastic on the console, remove it.
Select the manual mode.
Each time the
console is
turned on, the
manual mode
will be select-
ed. f a pace
program has
been selected,
reselect the
manual mode by pressing the Program button
repeatedly until the upper right corner of the dis-
play is blank.
Begin pedalling and adjust the resistance of
the pedals.
As you exercise, adjust the resistance of the ped-
als as desired by turning the resistance knob.
Follow your progress with the display.
When the con-
sole is turned
on, the scan
mode will be
selected, as
shown by the
mode bar
below the word
“SCAN.” As
you exercise,
the upper sec-
tion of the dis-
play will alternately show the elapsed time and the
distance that you have pedalled; the lower left
section of the display will alternately show the
number of calories you have burned and the num-
ber of fat calories you have burned; and the lower
right section will show your pedalling speed.
n addition, the pace indicator on the right side of
the display will provide a visual representation of
your pedalling pace. As you increase or decrease
your pace, the indicator will increase or decrease in
height.
To cancel the scan mode, press the Mode button.
The mode bar
below the word
“SCAN” will dis-
appear. The
upper section of
the display will
then show only
the elapsed
time, and the
lower left section of the display will show only the
number of calories you have burned. Press the
Mode button again. The upper section of the dis-
play will then show only the distance pedalled,
and the lower left section of the display will show
only the number of fat calories you have burned.
To select the scan mode again, press the Mode
button repeatedly until a mode bar appears below
the word “SCAN.”
To reset the display, press the On/Reset button.
Note: The console can show speed and dis-
tance in either miles or kilometers. To change
the unit of measurement, hold down the
On/Reset button for about six seconds. When
the batteries are replaced, it may be necessary
to reselect the desired unit of measurement.
Measure your heart rate if desired.
Note: If there
are thin sheets
of plastic on the
metal contacts
of the pulse
sensor, peel off
the plastic.
To use the pulse sensor, hold the handle on the
console, with your right palm covering the two
right contacts and your left palm covering the two
left contacts. Avoid moving your hands. When
your pulse is detected, the heart-shaped indicator
in the display will flash each time your heart beats
and two dashes (– –) will appear. After a moment,
your heart rate will be shown. For the most accu-
rate heart rate reading, continue to hold the hand-
grips for about 15 seconds.
When you are finished exercising, the console
will automatically turn off after a few minutes.
f the pedals are not moved and the console but-
tons are not pressed for a few minutes, the con-
sole will automatically turn off to conserve the
batteries.
6
5
4
3
2
1
This corner
should be blank
Pace ndicator
Mode Bar
Contacts
Handle
All manuals and user guides at all-guides.com

11
HOW TO USE A PACE PROGRAM
Turn on the console.
See step 1 on page 10.
Select one of the four pace programs.
Each time the
console is
turned on, the
manual mode
will be selected.
To select a
pace program,
press the
Program button
repeatedly until the number 1, 2, 3, or 4 appears
in the upper right corner of the display.
The four profiles on the right side of the console
show how the target pace will change during the
programs. For example, profile number 1 shows
that during program 1, the target pace will
increase near the beginning of the program, and
then decrease near the end.
Start the program.
To start the program, begin pedalling. Each pro-
gram consists of either 20 or 30 one-minute peri-
ods. One target pace is programmed for each
period. Note: The same target pace setting may
be programmed for two or more consecutive peri-
ods.
The target pace
settings for the
program will be
shown by the
target pace
indicator in the
display. (The
pace indicator
will show your
actual pedalling
pace.) As the
target pace indicator changes in height during the
program, adjust your pedalling pace so that both
indicators are at the same height. f your ped-
alling pace is slower than the current target pace
setting, an arrow will appear next to the pace
indicators to prompt you to increase your pace; if
your pace is faster than the target pace, an arrow
will prompt you to decrease your pace.
Important: The target pace settings for the
program are intended only to provide a goal.
Your actual pace may be slower than the tar-
get pace settings, especially during the first
few months of your exercise program. Make
sure to exercise at a pace that is comfortable
for you.
During the program, adjust the resistance of the
pedals as desired by turning the resistance knob.
The display will show the time remaining in the
program. f you continue exercising after the pro-
gram is completed, the display will continue to
show your exercise feedback.
Follow your progress with the display.
See step 4 on page 10.
Measure your heart rate if desired.
See step 5 on page 10.
When you are finished exercising, the console
will automatically turn off after a few minutes.
See step 6 on page 10.
6
5
4
3
2
1
Pace ndicator
Target Pace ndicator
All manuals and user guides at all-guides.com
all-guides.com

12
nspect and tighten all parts of the elliptical crosstrainer
regularly. Replace any worn parts immediately.
To clean the elliptical crosstrainer, use a damp cloth
and a small amount of mild soap. Important: Keep
liquids away from the console, place only a sealed
water bottle in the water bottle holder, and keep
the console out of direct sunlight. During storage,
remove the batteries from the console.
BATTERY REPLACEMENT
f the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
step 5 on page 6 and remove the console from the
upright. Next, see step 4 on page 6 and insert three
batteries into the console. Reattach the console to the
upright, being careful not to pinch the wires.
HOW TO AD UST THE REED SWITCH
f the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, you must remove the Left Pedal Arm (11) and
the Left Side Shield (3).
Remove the Pedal Arm Bolt Set (40), the M10 x
25mm Patch Screw (22), and the M10 Washer (35)
from the Left Pedal Arm (11). Remove the Left Pedal
Arm. Next, remove the two M4 x 25mm Screws (56)
and the four M4 x 16mm Screws (42) from the Left
Side Shield (3).
See the drawing below and locate the Reed Switch
(53). Loosen, but do not remove, the indicated M4 x
16mm Screw (42). Slide the Reed Switch slightly
toward or away from the Magnet (58) on the flywheel.
Retighten the Screw. Turn the left Pedal Disc (15) for a
moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjusted,
reattach the Left Side Shield (3) and the Left Pedal
Arm (11).
HOW TO AD UST THE DRIVE BELT
f the pedals slip whilst you are pedaling, even when
the resistance is adjusted to the highest setting, the
Drive Belt (19) may need to be adjusted. To adjust the
Drive Belt, you must first remove the left side shield.
See HOW TO ADJUST THE REED SW TCH at the
left and remove the left side shield.
Next, loosen the
M8 x 22mm Flat
Head Screw
(41) and turn
the M10 x
60mm Button
Bolt (62) until
the Drive Belt
(19) is tight.
When the Drive
Belt is tight,
tighten the Flat
Head Screw.
Reattach the left side shield.
MAINTENANCE AND TROUBLESHOOTING
42
56
42
42
22
35
3
40
15
41
62
19
11
58
53
42
All manuals and user guides at all-guides.com

13
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lowest number is the recommended heart rate for
fat burning, the middle number is the recommended
heart rate for maximum fat burning, and the highest
number is the recommended heart rate for aerobic
exercise.
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
f your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is between the lowest
number and the middle number in your training zone
as you exercise.
Aerobic Exercise
f your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exer-
cise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three work-
outs each week, with at least one day of rest between
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired.
Remember, the key to success is make exercise a
regular and enjoyable part of your everyday life.
WARNING:
• Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of
35 or persons with pre-existing health
problems.
• The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in deter-
mining heart rate trends in general.
All manuals and user guides at all-guides.com

14
Note: # indicates a non-illustrated part. Specifications are subject to change without notice.
Key No. Qty. Description Key No. Qty. Description
PART LIST—Model No. WLEVEL28840 R0604A
11Frame
21Upright
31Left Side Shield
41Right Side Shield
52Handlebar Arm
61Left Handlebar
71dler Assembly
81Right Handlebar
92M6 Washer
10 1 Front Stabiliser
11 1 Left Pedal Arm
12 1 Right Pedal Arm
13 2 Pedal
14 2 Axle Cap
15 2 Pedal Disc
16 2 Disc Crossbar
17 1 Flywheel
18 1 “C” Magnet
19 1 Drive Belt
20 2 M6 x 16mm Bolt
21 4 Endcap
22 2 M10 x 25mm Patch Screw
23 1 Console
24 2 Handgrip
25 2 Long Pedal Arm Bushing
26 1 Resistance Bracket
27 6 M6 Nylon Locknut
28 1 Rear Stabiliser
29 2 Flywheel Bearing
30 2 Large Snap Ring
31 2 Large Bearing
32 1 Pedal Axle
33 4 M10 Nylon Locknut
34 4 M8 x 53mm Button Bolt
35 2 M10 Washer
36 4 M6 x 48mm Flat Head Screw
37 2 Pedal Arm Bushing
38 10 M8 Nylon Locknut
39 2 Flywheel Washer
40 2 Pedal Arm Bolt Set
41 1 M8 x 22mm Flat Head Screw
42 24 M4 x 16mm Screw
44 1 Upper Wire
45 1 M8 x 25mm Button Screw
46 2 Handlebar Cap
47 2 Handlebar Spacer
48 4 M8 Washer
49 4 Small Handlebar Bushing
50 4 M8 x 38mm Button Bolt
51 8 M6 x 35mm Button Screw
52 1 Spring
53 1 Reed Switch/Wire
54 1 Cable Clamp
55 1 Lower Cable
56 2 M4 x 25mm Screw
57 1 M10 Flat Head Bolt
58 1 Magnet
59 6 M8 Split Washer
60 4 Large Handlebar Bushing
61 2 5/16” x 25.4mm Hex Bolt
62 1 M10 x 60mm Button Bolt
63 1 Console Bracket
64 1 M6 Nut
65 2 M6 x 40mm Bolt
66 2 Spacer
67 1 M6 x 38mm Bolt
68 6 M8 x 19mm Button Screw
69 2 Wheel
#3Hex Key
#1Grease
#1Userʼs Manual
All manuals and user guides at all-guides.com

EXPLODED DRAWING—Model No. WLEVEL28840 R0604A
15
24
8
4
3
42
42
5
47
42
23
44
24
6
47
5
60
68
17
21
34
57
10
39
12
35
37
51
15
19
16
61
61
16
62
1
30 31
32
38
38
51
51 15
13
37
35
11
40
40
20
7
59
59
58
38
50
50
38
60
60
2
49
49
49
49
42
42
42
42
42
21
60
51
51
41
54
42
53
38
25
25
40
40 13
28
21
21
38
34
30
31
55
46
46
14
14
36
36
29
29
22
22
56
39
66
27
27
66
33
20
26
27
38
18
64
67
52
27
9
9
69
69
65
27
65
27
42 42
68
68
63
45
59 59
68
59
68
42
42
48
42
42
48
48
42
All manuals and user guides at all-guides.com

Part No. 211891 R0604A Printed in China © 2004 CON P, nc.
ORDERING REPLACEMENT PARTS
To order replacement parts:
Tel:
Fax: [phone]
E-mail: [e-mail]
When ordering parts, please be prepared to give the following information:
• the MODEL NUMBER of the product (WLEVEL28840)
• the NAME of the product (BOOMERANG™850 elliptical crosstrainer)
• the SER AL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and the DESCR PT ON of the part(s) (see page 14)
0034 91 661 02 10
Manufactured in China for CON Health & Fitness, nc.
All manuals and user guides at all-guides.com
all-guides.com