Weslo WLEL09910 User manual

USER’S
MANUAL
CAUTION
Read all precautions and
instructions in this manual
before using this equipment.
Keep this manual for future
reference.
Model No. WLEL09910
Serial No.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are
committed to providing com-
plete customer satisfaction. If
you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!

2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE ELLIPTICAL GLIDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

3
1. Read all instructions in this manual before
using the elliptical glider.
2. Use the elliptical glider only as described in
this manual.
3. It is the responsibility of the owner to
ensure that all users of the elliptical glider
are adequately informed of all precautions.
4. Place the elliptical glider on a level surface,
with a mat beneath it to protect the floor or
carpet. Keep the elliptical glider indoors,
away from moisture and dust.
5. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
6. Keep children under the age of 12 and pets
away from the elliptical glider at all times.
7. The elliptical glider should not be used by
persons weighing more than 250 pounds.
8. Wear appropriate clothing when using the
elliptical glider. Always wear athletic shoes
for foot protection.
9. When mounting and dismounting the ellipti-
cal glider, always hold the handlebars and
step onto and off the pedal that is in the
lowest position.
10. Each time you stop exercising on the
elliptical glider, allow the pedals to come to
a complete stop before dismounting.
11. Always keep your back straight when using
the elliptical glider. Do not arch your back.
12. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
13. The elliptical glider is intended for in-home
use only. Do not use the elliptical glider in a
commercial, rental, or institutional setting.
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of serious injury, read the following important precau-
tions before using the WESLO®2.0 elliptical glider.
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health
problems. Read all instructions before using. ICON assumes no responsibility for personal injury
or property damage sustained by or through the use of this product.

4
BEFORE YOU BEGIN
Congratulations for selecting the WESLO®2.0 elliptical
glider. The 2.0 is an incredibly smooth exerciser that
moves your feet in a natural elliptical path, minimizing
the impact on your knees and ankles. And the unique
2.0 features adjustable resistance, upper-body handle-
bars, and a multi-mode exercise monitor to help you
get the most from your exercise. Welcome to a whole
new world of natural, elliptical-motion exercise from
WESLO.
For your benefit, read this manual carefully before
you use the elliptical glider. If you have questions
after reading the manual, call our Customer Service
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is WLEL09910. The
serial number can be found on a decal attached to the
elliptical glider (see the front cover of this manual for
the location of the decal).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
Resistance Knob
FRONT
BACK
LEFT SIDE
Pedal Arm
Side Shield
Pedal
Remote Holder
Upright
Water Bottle Holder
(Bottle not included)
Handlebar

5
PART IDENTIFICATION CHART
Use the chart below to identify the small parts used in
assembly. The number in parenthesis below each part
refers to the key number of the part, from the PART
LIST on page 14. The number after the dash indicates
the quantity needed for assembly. Note: Some parts
may have been pre-attached for shipping. If a part
is not in the parts bag, check to see if it has been
pre-attached.
M8 x 19mm
Button Screw (10)–2
M8 x 63mm Carriage Bolt (49)–4
M5 x 30mm
Button Bolt (51)–4
M8 x 38mm Button Bolt (53)–2
M4 x 12mm
Button Screw (57)–4
M5 Nylon
Locknut (52)–4 M8 Nylon
Locknut (50)–8 1/2” Nylon
Locknut (35)–2
M8 x 60mm Bolt (56)–2
Pivot Washer (54)–2 Pedal Washer (32)–2
M4 x 19mm Flange
Screw (55)–6
Note: Extra parts may be included.

6
ASSEMBLY
Assembly requires two people. Place all parts of the elliptical glider in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires that you have two adjustable wrenches , a rubber mallet , and
the included allen wrench .
1. Identify the Front Stabilizer (18), which is the nar-
rowest Stabilizer. If there are no Stabilizer Endcaps
(20) on the Front Stabilizer, push one onto each end.
Attach the Front Stabilizer (18) to the front of the
Frame (1) with two M8 x 63mm Carriage Bolts (49)
and two M8 Nylon Locknuts (50).
2. If there are no Stabilizer Endcaps (20) on the Rear
Stabilizer (19), push one onto each end.
Attach the Rear Stabilizer (19) to the Frame (1) with
two M8 x 63mm Carriage Bolts (49) and two M8
Nylon Locknuts (50).
3. While a second person holds the Upright (2) near
the Frame (1), connect the Extension Wire (47) to
the Reed Switch Wire (41).
Insert the Upright (2) into the Frame (1), being care-
ful to avoid damaging the wires. Make sure that the
Frame Bushings (3) are inserted fully into the
Frame. Adjust the Upright (2) so that a bolt can be
inserted through the center hole in each side.
Secure the Upright with two M8 x 38mm Button
Bolts (53) and two M8 Nylon Locknuts (50).
20
2
3
1
18
49
20
50
19
20
50
49
2
3
3
50
41
47 50
53
1
1
50
50
1
20

7
5. Identify the Left Pivot Arm (6), which is marked with a
sticker that has an “L” on it. Make sure that there are
two Pivot Bushings (9) in the Left Pivot Arm. Slide the
Left Pivot Arm onto the Pivot Axle, making sure that it
is oriented as shown. Put a Pivot Washer (54) onto
an M8 x 19mm Button Screw (10) and tighten the
Button Screw into the Pivot Axle.
6. Insert a Handlebar (12) into the Right Pivot Arm (7).
Slide the Foam Grip (13) up to expose the mounting
holes. Secure the Handlebar with two M5 x 30mm
Button Bolts (51) and two M5 Nylon Locknuts (52).
Slide the Foam Grip down over the Button Bolts and
Nylon Locknuts.
Attach the other Handlebar to the Left Pivot Arm (6) in
the same manner.
5
9
10
54
9
6
13
51
52
6
7
6
11
12
4. Make sure that the two Upright Bushings (8) are
inserted into the Upright (2). Apply a thin film of the
included grease to the length of the Pivot Axle (11).
Insert the Pivot Axle into the Upright Bushings and
the Upright.
Identify the Right Pivot Arm (7), which is marked with
a sticker that has an “R” on it. Make sure that there
are two Pivot Bushings (9) in the Right Pivot Arm.
Slide the Right Pivot Arm onto the Pivot Axle (11),
making sure that it is oriented as shown. Put a Pivot
Washer (54) onto an M8 x 19mm Button Screw (10)
and tighten the Button Screw into the Pivot Axle.
49
8
8
27
11
Grease
10
9
54

8
10. Make sure that all parts of the elliptical glider are properly tightened. Place a mat under the elliptical glider
to protect the floor or carpet from damage.
9
57
5
47
Console
Wire
28
29
2
9. The Console (5) requires two “AA” batteries (not
included). Alkaline batteries are recommended.
To install batteries, look under the Console (5) and
locate the battery compartment. Insert two batteries
into the battery compartment; make sure that the
batteries are turned so the negative ends (marked
“–”) are touching the springs in the battery com-
partment.
Connect the console wire to the Extension Wire (47).
Attach the Console (5) to the Upright (2) with four M4
x 12mm Button Screws (57).
Push the Resistance Knob (28) firmly onto the
Resistance Cable (29).
8. Identify the Left Pedal Arm (14), which is marked with
a sticker that has an “L” on it. Make sure that there are
two Pedal Arm Bushings (33) in the Left Pedal Arm.
Apply a thin film of the included grease to a Pedal
Axle (34). Insert the Pedal Axle into the Left Pedal
Arm, and slide a Pedal Washer (32) onto the Pedal
Axle. Firmly tighten the Pedal Axle into the Crank (30).
Tighten a 1/2” Nylon Locknut (35) onto the end of the
Pedal Axle protruding from the Crank.
Make sure that there are two Small Pivot Bushings
(42) in the Left Pivot Arm (6). Apply a thin film of the
included grease to an M8 x 60mm Bolt (56). Attach
the Left Pivot Arm to the Left Pedal Arm (14) with the
Bolt and an M8 Nylon Locknut (50).
Attach the Right Pedal Arm (not shown) in the same
manner.
8
7. Identify the Left Pedal Arm (14), which is marked with
a sticker that has an “L” on it. Next, identify the Left
Pedal (16), which has an “L” molded into the bottom.
Attach the Left Pedal to the Left Pedal Arm with three
M4 x 19mm Flange Screws (55).
Attach the Right Pedal to the Right Pedal Arm (not
shown) in the same manner.
7
34 33
33
35
42
42
50
56
14
14
55
16
32 30
6
Batteries
5
Grease

9
HOW TO USE THE ELLIPTICAL GLIDER
HOW TO EXERCISE ON THE ELLIPTICAL GLIDER
To mount the elliptical glider, firmly hold the handle-
bars and carefully step onto the pedal that is in the
lowest position. Next, step onto the other pedal. Push
the pedals until they begin to move with a continuous
motion. Note: The pedals can turn in either direc-
tion. It is recommended that you turn the pedals
in the direction shown below; however, to give
variety to your exercise, you may choose to turn
the pedals in the opposite direction.
To dismount the elliptical glider, allow the pedals to
come to a complete stop. CAUTION: The elliptical
glider does not have a free wheel; the pedals will
continue to move until the flywheel stops. When
the pedals are stationary, step off the highest pedal
first. Then, step off the lowest pedal.
HOW TO ADJUST THE RESISTANCE OF THE
PEDALS
As you exercise,
you can adjust the
resistance of the
pedals with the
resistance knob.
To increase the
resistance, turn
the knob clock-
wise; to decrease
the resistance,
turn the knob
counterclockwise.
Pedal
Resistance
Knob

10
DESCRIPTION OF THE CONSOLE
The innovative console features five modes that dis-
play instant exercise feedback. The modes are
described below:
Speed—This mode shows your exercise pace, in rev-
olutions per minute.
Revolutions—This mode shows the total number of rev-
olutions you have pedaled.
Calories—This mode shows the approximate number
of calories you have burned.
Time—This mode will show the elapsed time. Note:
When you stop exercising, the time will flash when it
is displayed.
Scan—This mode displays the other four modes, for
five seconds each, in a repeating cycle.
BATTERY INSTALLATION
Before the console can be operated, two “AA” batter-
ies must be installed. If you have not installed batter-
ies, see assembly step 9 on page 8. Note: It will be
necessary to remove the console to install batteries.
HOW TO OPERATE THE CONSOLE
1. To turn on the power, press the on/reset button or
simply begin pedaling. When the power is turned
on, the entire display will appear for two seconds.
The console will then be ready for operation.
2. Select one of the five modes:
Scan mode—
When the
power is
turned on, the
scan mode will
automatically
be selected.
One mode
indicator will show that the scan mode is selected,
and a flashing mode indicator will show which
mode is currently displayed. Note: If a different
mode is selected, you can select the scan mode
again by repeatedly pressing the display button.
Speed, time,
revolutions, or
calories
mode—To
select one of
these modes
for continuous
display,
repeatedly press the display button. The mode indi-
cators will show which mode is selected. (Make
sure that the scan mode is not selected.)
3. To reset the display, press the on/reset button.
4. To turn off the power, simply wait for about four
minutes. Note: The console has an “auto-off”
feature. If the pedals are not moved and the
console buttons are not pressed for four min-
utes, the power will turn off automatically in
order to conserve the batteries.
Mode Indicators
Mode Indicator