Weslo WLEL33408.0 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. eep this manu-
al for future reference.
Serial
Number
Decal
Model No. WLEL33408.0
Serial No.
Write the serial number in the
space above for reference. USERʼS MANUAL
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
V
QUESTIONS?
As a manufacturer, we are commit-
ted to providing complete customer
satisfaction. If you have questions,
or if parts are damaged or missing,
PLEASE DO NOT CONTACT THE
STORE; please contact Customer
Care.
IMPORTANT: You must note the
product model number and serial
number (see the drawing above)
before contacting us:
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com

TABLE OF CONTENTS
WARNINGDECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEELLIPTICALEXERCISER ..................................................11
MAINTENANCEANDTROUBLESHOOTING ...................................................18
EXERCISEGUIDELINES ...................................................................19
PARTLIST ..............................................................................20
EXPLODEDDRAWING ....................................................................22
ORDERINGREPLACEMENTPARTS ..................................................BackCover
LIMITEDWARRANTY ..............................................................BackCover
2
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, call the telephone number
on the front cover of this manual and
request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.

3
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional set-
ting.
4. eep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. eep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exer-
ciser. Always wear athletic shoes for foot
protection.
9. Hold the handgrip pulse sensor or the upper
body arms when mounting, dismounting, or
using your elliptical exerciser.
10. eep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
14. Use your elliptical exerciser only as
described in this manual.
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS

4
BEFORE YOU BEGIN
Congratulations for selecting the new WESLO PRO™
13.8E elliptical exerciser. The 13.8E is an incredibly
smooth exerciser that moves your feet in a natural
elliptical path, minimizing the impact on your knees
and ankles. The unique 13.8E features adjustable
resistance and an advanced console to help you get
the most from your exercise.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.wesloservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handgrip Pulse Sensor
Handlebar
Pedal Disc
Wheel
Pedal
Console
Water Bottle Holder*
Fan
*Water bottle is not included

5
M10 x 112mm Carriage Bolt (34)–4
M10 x 88mm Button Screw (63)–2
M10 x 52mm Bolt Set (27)–2
M10 Split
Washer (70)–2
M8 Large
Washer (53)–10
Wave Washer
(95)–2
M8 Split
Washer (100)–4
M8 x 65mm Button Screw (99)–4
M8 x 50mm Button
Screw (89)–4
M10 Locknut
(29)–4
M8 Locknut
(46)–12
M4 x 16mm
Screw (66)–4
M4 x 22mm
Screw (91)–2
M8 x 25mm Patch
Screw (22)–2
M8 x 45mm Button
Bolt (50)–4
M8 x 38mm Button
Bolt (112)–4
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tools, assembly requires a Phillips screwdriver , an adjustable
wrench , and a rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-
ses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The
number following the parentheses is the quantity needed for assembly. Note: Some small parts may have
been preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.

6
1.
Identify the Front Stabilizer (3). Make sure that
the Front Stabilizer is turned so that the
Wheels (32) are not touching the floor.
While another person lifts the front of the Frame
(1), attach the Front Stabilizer (3) to the Frame
with two M10 x 112mm Carriage Bolts (34) and
two M10 Locknuts (29).
3
29
29
32
32
34
1
1
2. While another person lifts the back of the
Frame (1), attach the Rear Stabilizer (4) to the
Frame with two M10 x 112mm Carriage Bolts
(34) and two M10 Locknuts (29).
34
4
1
29
29
To make assembly easier, read the
information on page 5 before you begin
assembling the elliptical exerciser.
2

7
3
2
86
87
1
63
83
70
70
91
105
83
3. While another person holds the Upright (2) in
the position shown, connect the Upper Wire
Harness (86) to the Lower Wire Harness (87).
Tip: Avoid pinching the Wire Harnesses (86,
87). Insert the Upright (2) into the Frame (1).
Next, slide an M10 Split Washer (70) and a
Frame Spacer (83) onto each of the two M10 x
88mm Button Screws (63).
Insert the M10 x 88mm Button Screws (63) into
the Frame (1) and the Upright (2). Make sure
that the concave sides of the Frame Spacers
(83) are facing the Frame. Do not tighten the
Button Screws yet.
Attach the Water Bottle Holder (105) to the
Upright (2) with two M4 x 22mm Screws (91).
Do not pinch the Wire
Harnesses (86, 87)
during this step
4. Identify the Left Pulse Bar (107), which is
marked with a “Left” sticker.
Have another person hold the Left Pulse Bar
(107) near the left side of the Upright (2). Make
sure that the hexagonal holes are in the
indicated location.
See the inset drawing. Locate the wire tie in
the Upright (2). Tie the lower end of the wire tie
to the left Pulse Wire (113). Next, pull the upper
end of the wire tie upward out of the top of the
Upright. Then, untie and discard the wire tie.
Tip: Avoid pinching the wires. Slide the Left
Pulse Bar (107) onto the Upright (2). Attach the
Left Pulse Bar with two M8 x 38mm Button
Bolts (112) and two M8 Locknuts (46). Make
sure that the Locknuts are in the hexagonal
holes.
Repeat this step for the Right Pulse Bar
(108).
107
46
2
108
112
113
113
Hexagonal
Holes
4
Avoid pinching
the wires
86
Wire Ties
Wire Tie
113

8
5. The Console (5) can use four 1.5V “D” batteries
(not included); alkaline batteries are recom-
mended. IMPORTANT: If the Console has
been exposed to cold temperatures, allow it
to warm to room temperature before insert-
ing batteries. Otherwise, you may damage
the console displays or other electronic
components. Remove the battery cover, insert
the batteries into the battery compartment, and
reattach the battery cover. Make sure to orient
the batteries as shown by the diagram inside
the battery compartment.
To purchase an optional AC adapter, contact
the store where you purchased this product
or call the telephone number on the cover of
this manual. To avoid damaging the console,
use only a manufacturer-supplied AC
adapter. Plug one end of the AC adapter into
the jack on the console; plug the other end into
an outlet installed in accordance with all local
codes and ordinances.
5
5
Batteries
Battery
Cover
6. While another person holds the Console (5)
near the Upright (2), connect the console wire
to the Upper Wire Harness (86). Then, connect
the console pulse wires to the Pulse Wires
(113). Insert the excess wire downward into the
Upright.
Tip: Avoid pinching the wires. Attach the
Console (5) to the Upright (2) with four M4 x
16mm Screws (66).
5
86
113
66
2
Console
Wire
Pulse
Wires
6

9
7. Identify the Left Handlebar (9), which is marked
with a “Left” sticker.
Insert the Left Handlebar (9) into an Upper
Body Leg (79). Make sure that the hexagonal
holes are in the indicated location.
Attach the Left Handlebar (9) to the Upper Body
Leg (79) with two M8 x 45mm Button Bolts (50)
and two M8 Locknuts (46). Make sure that the
Locknuts are inside the hexagonal holes. Do
not tighten the Button Bolts yet.
Repeat this step for the Right Handlebar
(not shown) and the other Upper Body Leg
(not shown).
8. Apply a generous amount of the included
grease to the Pivot Axle (97) and to two Wave
Washers (95).
Insert the Pivot Axle (97) into the Upright (2).
Slide a Handlebar Spacer (25) onto the short
tube on the Left Handlebar (9), and rotate the
Handlebar Spacer so that the small arrow is
pointing toward the floor.
Slide a Wave Washer (95) onto the left end of
the Pivot Axle (97). Then, slide the Left
Handlebar (9) onto the left end of the Pivot
Axle.
Attach the Right Handlebar (10) in the same
way.
7
9
50
46
Hexagonal
Holes
79
8
2
9
10
Grease
Tube
Arrow
97
25
95

10
10. Apply grease to the barrel of an M10 x 52mm
Bolt Set (27) and to the surfaces of the two Leg
Bushings (28) in the left Upper Body Leg (79).
Next, attach the left Upper Body Leg (79) to the
Left Pedal Arm (14) with the M10 x 52mm Bolt
Set (27). Do not overtighten the Bolt Set; the
left Upper Body Leg must pivot freely.
Attach the right Upper Body Leg (79) to the
Right Pedal Arm (103) in the same way.
See step 3. Tighten the M10 x 88mm Button
Screws (63).
See step 7. Tighten the M8 x 45mm Button
Bolts (50) in the Upper Body Legs (79).
14
103
27
27
28 28
Grease
Grease
10
79
79
9
23
23
22 53
22
53
97
25
25
9. Tighten an M8 x 25mm Patch Screw (22) and an
M8 Large Washer (53) into each end of the Pivot
Axle (97).
Attach the Handlebar Caps (23) by pressing the
small tabs into the Handlebar Spacers (25).
12. Make sure that all parts are properly tightened. Note: Some hardware may be left over after assembly is
completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser.
11
12
16
99
14
13
11. Attach a Pedal Bracket (16) to the Left Pedal
Arm (14) with two M8 x 65mm Button Screws
(99), two M8 Large Washers (53), and two M8
Locknuts (46).
Identify the Left Pedal (13), which is marked
with a “Left” sticker. Attach the Left Pedal to the
Left Pedal Arm (14) with two M8 x 50mm Button
Screws (89), two M8 Split Washers (100), and
two M8 Large Washers (53).
Attach the other Pedal Bracket (not shown)
and the Right Pedal (12) to the Right Pedal
Arm (103) in the same way.
103
53
53
53
46
89
100