Westin 46-23785 User manual

1
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-0676 RevA ECO #: W13-0110 DATE: 3/11/14
APPLICATION: 2015 CHEVY SILVERADO 2500/3500 WINCH TRAY
2015 CHEVY SILVERADO 2500/3500 WINCH TRAY MOUNTED SPORTSMAN & HDX GG
APPLICATION PART #’S 46-23785, 45-93780, 40-93785, 57-93780, 57-93785
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
11WINCH TRAY RATCHET
2,3 2WINCH TRAY INNER MOUNTING BRACKETS (DRV & PASS) SCREWDRIVER
42WINCH TRAY OUTER MOUNTING BRACKETS 15MM WRENCH
52WINCH TRAY MIDDLE MOUNTING BRACKETS 15MM SOCKET
624 M10 HEX HEAD BOLT ALLEN WRENCH
748 M10 FLAT WASHER 18MM WRENCH
824 M10 LOCK WASHER 18MM SOCKET
924 M10 HEX NUT 10MM SOCKET
10 12 M12 HEX HEAD BOLT 16MM SOCKET
11 24 M12 FLAT WASHER 16MM WRENCH
12 14 M12 LOCK WASHER RATCHET EXT.
13 14 M12 HEX NUT TORQUE WRENCH
14 2M12 LARGE FLAT WASHER
15 2M12 FLANGE BOLT
16 2M12 SQUARE POLY BOLT RETAINER
17 1HDX GRILLE GUARD (57-93780, 57-93785 ONLY)
18 1SPORTSMAN GRILLE GUARD (45-93780, 40-93785 ONLY)
19,20 2SUPPORT STRAPS DRV & PASS (57-93780/85, 45-93780, 40-93785
ONLY)
21 2SPACER BLOCKS (57-93780/85, 45-93780, 40-93785 ONLY)
22 2M10 STAINLESS SHORT BUTTON HEAD BOLT (57-93780/85, 45-
93780, 40-93785 ONLY)
23 8M10 STAINLESS CUPPED WASHER (57-93780/85, 45-93780, 40-
93785 ONLY)
24 2M10 STAINLESS FLANGE NUT (57-93780/85, 45-93780, 40-93785
ONLY)
25 6M10 STAINLESS LONG BUTTON HEAD BOLT (57-93780/85, 45-
93780, 40-93785 ONLY)
INSTRUCTIONS—INSTRUCCIONES—CONSIGNES
AUTOMOTIVE PRODUCTS, INC.
1. Remove contents from box, verify if all parts listed are present and free from damage. Carefully read and understand all instruc-
tions before attempting installation.
2. Remove the factory tow hooks (if equipped). They cannot be re-used.
3. One side at a time slip the Winch Tray Inner Mounting Brackets and the Winch Tray Outer Mounting Brackets through the tow
hook pockets. Note: Do not fasten either bracket until both have been properly positioned.
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING

2
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-0676 RevA ECO #: W13-0110 DATE: 3/11/14
Loosely attach Outer Brack-
ets using M12 Flange Bolts
(DRV Side Shown).
Fig. 1 Fig. 2
Loosely attach Inner
Brackets using M12 Hard-
ware.
Fig. 3
Loosely install M12 hard-
ware through the tow hook
holes in the frame to attach
both mounting brackets.
Fig. 4
Loosely attach all three brackets on both
sides using M10 hardware.
4. Loosely attach the Winch Tray Outer Mounting Brackets to the vehicle’s frame using the supplied M12 Flange Bolts as shown
in Figure 1. Note: The flange bolts may be held in place using the M12 Poly Retainers while positioning the bracket.
5. Loosely attach the Winch Tray Inner Mounting Brackets to the vehicle’s frame using M12 Hardware as shown in Figure 2.
Note: The Large M12 Washer covers the large hole in the frame.
Large Flat Washer.
6. Using the supplied M12 Hardware loosely attach both mounting brackets to the frame holes that were used for the tow hooks
as shown in Figure 3.
7. Position the Middle Winch Tray Mounting Brackets as shown in Figure 4 then loosely attach them using the supplied M10
hardware.
8. Loosely attach the Inner and Outer Mounting brackets together using M10 hardware as shown in Figure 4.
9. Loosely attach the winch tray to the brackets using M10 hardware on the sides and M12 hardware on the bottom of the tray as
shown in Figure 5.
10. Install the winch per the winch manufacturer’s instructions.
11. If installing a Winch Mount Grille Guard continue to step 12. Otherwise align and adjust the tray and brackets as necessary
then tighten and torque all fasteners: M10 to 30-35 ft-lbs.; M12 to 50-55 ft-lbs.
11, 12, 13
14
11, 12, 13
10, 11
11, 12, 13
10, 11

3
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-0676 RevA ECO #: W13-0110 DATE: 3/11/14
Attach the tray to the
Inner Brackets using
M12 hardware.
Fig. 5
12. If installing a Winch Tray Mount Grille Guard remove the vehicle’s radiator cover and grille as shown in Figures 6 & 7.
13. Remove the factory M12 bumper bolts from each side as shown in Figure 8.
14. Install the Support Straps by re-using the factory bumper bolts. Center the Support Straps and space them 42-3/4” apart
(outside edge to outside edge). Tighten and torque these fasteners to 50-55 ft-lbs. Refer to Figure 9.
Attach the tray to the Outer
Brackets using M10 hardware.
Pull up all fasteners and re-
move plastic radiator cover.
Fig. 6 Fig. 7
Remove all of the screws holding the grille to the upper radiator
support and carefully pull it from the vehicle. Note: there are
several inaccessible clips that provide some retention on the
grille. They will pop loose when you pull on the grille.
Remove these bumper
bolts from both sides.
Fig. 8 Fig. 9
Install the Support Straps. Center them,
space them to 42-3/4” and tighten them
before re-installing the grille.
42-3/4”
6, 7
7, 8, 9
11, 12, 13
10, 11

4
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-0676 RevA ECO #: W13-0110 DATE: 3/11/14
15. Re-install the vehicle’s grille and plastic radiator cover in the reverse order that they were removed. Note: The bottom of the
grill may need to be squeezed past the Support Brackets.
16. Remove the bolts from the Winch Tray shown in Figure 10.
17. Use an assistant to line up the Spacer Blocks with the Winch Tray as shown in Figure 11.
Fig. 10
Remove hardware from these holes.
18. While the assistant holds the Spacer Blocks in place, position the Grille Guard over the Spacer Blocks and loosely attach it to
the Support Straps using the short M10 Button Head Hardware as shown in Figure 12.
19. Attach the Grille Guard to the Winch Tray using the long M10 Button Head Hardware. These bolts need to go through the
Grille Guard, Spacer Blocks, Outer Mount Brackets and Winch Tray. Note: Nuts and washers from the Winch Tray bolt kit
need to be used to accomplish this. Refer to Figure 12.
20. Align and adjust the Grille Guard as necessary. Tighten and torque all hardware as follows: M10 to 30-35 ft-lbs.; M12 50-
55 ft-lbs.
Fig. 11
Hold up Spacer Blocks as
shown.
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.

5
Westin Automotive Products, Inc.
320 Covina Blvd
San Dimas, Ca. 91773
Thank You for choosing Westin products
For Additional installation assistance please call
Customer service [phone]
www.westinautomotive.com
P.N.: 75-0676 RevA ECO #: W13-0110 DATE: 3/11/14
Sportsman Winch GG Installation Complete HDX Winch GG Installation Complete
Fig. 12
Attach Grille Guard to Winch
Tray and Brackets (all compo-
nents are labeled for reference).
HDX shown, Sportsman similar.