Westin 58-41025 User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1 1 DRIVER SIDE POD ASSEMBLY 10MM SOCKET
2 1 PASSENGER SIDE POD ASSEMBLY 10MM WRENCH
3 2 MESH COVER PLATE 13MM SOCKET
4 1 CENTER SECTION 13MM WRENCH
5 1 VALANCE SKID PLATE 16MM SOCKET
6 1 DRIVER MOUNTING BRACKET 16MM WRENCH
7 1 PASSENGER MOUNTING BRACKET 18MM SOCKET
8 1 M10 NUT PLATE 19MM WRENCH
9 6 SENSOR TAB RATCHET
10 1 M10 BOLT PLATE TORQUE WRENCH
11 1 DRIVER SIDE STRAP
12 1 PASSENGER SIDE STRAP
13 1 DRIVER VALANCE MOUNT BRACKET
14 1 PASSENGER VALANCE MOUNT BRACKET
15 1 DRIVER FILLER TRIANGLE
16 1 PASSENGER FILLER TRIANGLE
17 2 LED BRACKET
18 6 HOLE PLUG
19 10 M12 HEX HEAD BOLT (YELLOW ZINC)
20 10 M12 HEX NUT (YELLOW ZINC)
21 20 M12 FLAT WASHER (YELLOW ZINC)
22 20 M12 SPLIT LOCK WASHER (YELLOW ZINC)
23 6 M6 CARRIAGE BOLT (YELLOW ZINC)
24 6 M6 SPLIT LOCK WASHER (YELLOW ZINC)
25 6 M6 HEX NUT (YELLOW ZINC)
26 6 M6 FLAT WASHER (YELLOW ZINC)
27 6 M10 HEX HEAD BOLT (YELLOW ZINC)
28 6 M10 SPLIT LOCK WASHER (YELLOW ZINC)
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
PRO-MOD FRONT BUMPER
APPLICATION:
2013-2018 Ram 1500; 2019 Ram 1500 Classic
PART NUMBER:
58-41025

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
29 12 M10 FLAT WASHER (YELLOW ZINC)
30 6 M10 HEX NUT (YELLOW ZINC)
31 4 M8 U-CLIPS (YELLOW ZINC)
32 12 M8 BUTTON HEAD BOLT (BLACK ZINC)
33 26 M8 FLAT WASHER (BLACK ZINC)
34 14 M8 SPLIT LOCK WASHER (BLACK ZINC)
35 10 M8 HEX NUT (BLACK ZINC)
36 2 M8 HEX HEAD BOLT (BLACK ZINC)
37 12 M6 FLAT WASHER (BLACK ZINC)
38 12 M6 SPLIT LOCK WASHER (BLACK ZINC)
39 12 M6 BUTTON HEAD BOLT (BLACK ZINC)
40 12 M6 SERRATED FLANGE NUT (BLACK ZINC)
41 2 LONG M10 HEX HEAD BOLT (BLACK ZINC)
42 3 M10 HEX NUT (BLACK ZINC)
43 6 M10 FLAT WASHER (BLACK ZINC)
44 4 M10 SPLIT LOCK WASHER (BLACK ZINC)
45 1 SHORT M10 HEX HEAD BOLT (BLACK ZINC)
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
ITEM 1 ITEM 2 ITEM 3
ITEM 4 ITEM 5
ITEM 6 ITEM 9 ITEM 11 ITEM 13
ITEM 15 ITEM 17 ITEM 18
Passenger Opposite Passenger Opposite Passenger Opposite
Passenger Opposite

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
Driver’s Side
Figure 1
Passenger’s side
Figure 2
Passenger’s side
Figure 3
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage. Carefully read and understand all
instructions before attempting installation. Failure to identify damage before installation could lead to a rejection of
any claim.
2. Disconnect any electrical connectors that are attached to front bumper. Including parking sensor harness, fog lights, etc.
3. Remove tow hooks if equipped.
4. Locate original nuts fastening bumper to frame and remove using 18mm wrench. See Figures 1 & 2.
5. Carefully remove bumper assembly. See Figure 3.
5. Remove filler panel between bumper and grille. Start by removing screws around fender area fastening the filler panel to
the body of the truck. Use a 10mm socket. See Figure 4 –5.
Figure 4
Image shows location of screws
that need to be removed. (Filler
panel removed)
6. After all screws holding filler panel have been removed, care-
fully pull starting from either side and un-clip tabs holding
filler panel to the truck.
Tabs
Figure 5

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
Figure 6
7. Remove plastic pieces behind filler panel using 10mm
socket. Once all screws have been removed, carefully pull
plastic pieces and un-clip tabs around grille area. See Fig-
ures 6-7.
Figure 7
8. Use the supplied M10 Hardware to attach each Side Pod Assembly (1,2) to the Center Section (4). See Figure 8.
9. Use the supplied M6 Hardware to attach the LED Brackets (17) to the center section. See Figure 9. Note: If installing an
LED Light Bar (sold separately), install it at this time.
Fig. 8
Driver Side Shown
Fig. 9
Driver Side Shown
17
4
39
38
37
40
30 28
29
27

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
10. Loosely install the bumper assembly to the Mounting Brackets (6,7) using the supplied M12 Hardware. See Figures 10 &
11.
Fig. 10 Fig. 11
Driver Side Shown Driver Side Shown
11. Remove the parking sensors from the OEM bumper.
12. Use the Sensor Tab (9) along with the supplied M6 Hardware (23-26) to install the sensors as shown in Figure 12.
PARKING SENSOR INSTALLATION
*If not installing sensors, install Hole Plugs (18) into holes on bumper and proceed
Factory Sensor
Item 10
Items 15-18
Fig. 12

6
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
13. Install the Filler Triangles (15,16) on the vehicle just below the headlight using the supplied M8 Hardware. See Figure 13.
14. Install the preassembled bumper and mounting brackets along with the Valance Mounting Brackets (13,14) to the frame
using the supplied M12 and M10 Hardware. See Figure 14.
Driver Side ShownPassenger Side Shown
Item 16
Fig. 13 Fig. 14
Use items 36,34,33,35 to se-
cure the filler panel as shown.
Items 19,21,22,20
Items 27,29,28,30
Item 13
15. On the passenger side, use the M10 Bolt Plate (10) along with the M10 Hardware to attach the Side Strap (12) to the frame.
See Figure 15.
16. On the driver side, use the M10 Nut Plate (8) along with the M10 Hardware to attach the Side Strap (11) to the frame. See
Figure 16.
Passenger Side Shown
Large Skid Plate
Sold Separately
Fig. 15
Item 10
Use black M10 Hard-
ware. Bottom will use
Item 41 along with
washers and nut.
Driver Side Shown
Insert Item 8 through
top until aligned as
shown. Fasten using
Item 45 and washers.
Items 41,43,44,42
Fig. 16

7
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
17. Attach both Side Straps (11,12) to the bumper using the supplied M8 Hardware. See Figure 17.
18. Attach the Mesh Side Covers (3) to the Bumper using the supplied M6 Hardware. See Figures 18 & 19.
Driver Side Shown
38
37
39
Fig. 18
Fig. 19
Fig. 17
Driver Side Shown
3 40

8
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
19. Align bumper as desired and torque all hardware as specified: M6 to 7 ft-lbs, M8 to 18 ft-lbs, M10 to 38 ft-lbs, M12 to 60
ft-lbs.
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER
INSTALLATION COMPLETE
LED Light Bar Sold Separately

9
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5841025-RevA ECO #: W18-0229 DATE: 04/15/19
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer, birth defects or
other reproductive harm. For more info go to www.p65warnings.ca.gov