Westin E Series User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-31402-RevA ECO #: W19-0162 DATE: 12/30/19
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
1 1 BULL BAR 17MM SOCKET
2 1 DRIVER MOUNTING BRACKET 17MM WRENCH
3 1 PASSENGER MOUNTING BRACKET RATCHET
4 2 M12 HEX HEAD BOLT (YELLOW ZINC) TORQUE WRENCH
5 2 M12 FLAT WASHERS (YELLOW ZINC) ALLEN
6 2 M12 SERRATED FLANGE NUT (YELLOW ZINC) 21MM SOCKET
7 4 M10 BUTTON HEAD BOLT (BLACK ZINC) 18MM WRENCH
8 4 M10 FLAT WASHER (BLACK ZINC) 18MM SOCKET
9 4 M10 SERRATED FLANGE NUT (BLACK ZINC) BREAKER BAR
10 4 M10 SPLIT LOCK WASHER (BLACK ZINC)
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
E-SERIES BULL BAR
APPLICATION:
2019-2020 RAM 2500/3500
PART NUMBER:
31-4020, 31-4025
ITEM 1 ITEM 2
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
ITEM 3

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-31402-RevA ECO #: W19-0162 DATE: 12/30/19
2. Start below the front of the vehicle. Unbolt the two factory bolts (three if tow hooks are equipped) from the bumper bracket
on each side. See Figure 1. Note: Factory Tow hooks cannot be reused!
Remove
Fig. 1
3. Unplug any lights or wiring and remove the bumper.
4. Remove the top nuts off of each bumper bracket. Remove the bracket. See Figure 2

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-31402-RevA ECO #: W19-0162 DATE: 12/30/19
Fig. 2
5. Slide either mounting bracket (2,3) into the factory bumper bracket as shown in Figure 3.
Fig. 3
ITEM 2
Factory
Bracket

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-31402-RevA ECO #: W19-0162 DATE: 12/30/19
6. Rotate and slide both brackets back through the front bumper as shown in Figures 4-5
Front Bumper
Item 2
Factory
Bracket
Figure 4 Figure 5
7. Re-Install the factory bumper bracket to the bumper.
8. Using supplied M12 hardware and reusing factory hardware, loosely install the mounting bracket. Re install the front
bumper and torque to factory specs. The brackets should slide through the tow hook pockets. See Figure 6
4
5
62
Figure 6
Factory Hardware
Frame
Bumper
Bracket
Driver side shown

5
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-31402-RevA ECO #: W19-0162 DATE: 12/30/19
9. Using the supplied M10 hardware, loosely install the bull bar to the mounting brackets. See Figure 7.
7
9
10
8
2
1
Figure 7
11. Align bull bar as necessary and torque hardware as specified: M10 to 40 ft-lbs, M12 to 60 ft-lbs.
Install Complete
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER.
Front
Driver side shown

6
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-31402-RevA ECO #: W19-0162 DATE: 12/30/19
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer, birth defects or
other reproductive harm. For more info go to www.p65warnings.ca.gov