Westin OUTLAW NERF STEP BARS User manual

1
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5852775-RevA ECO #: W18-0157 DATE: 04/16/19
INSTALLATION INSTRUCTIONS
ITEM QUANTITY DESCRIPTION TOOLS NEEDED
11DRIVER STEP BAR ASSEMBLY 13MM SOCKET
21PASSENGER STEP BAR ASSEMBLY 13MM WRENCH
31DRIVER FRONT MOUNTING BRACKET 16MM SOCKET
41PASSENGER FRONT MOUNTING BRACKET 16MM WRENCH
51DRIVER CENTER MOUNTING BRACKET RATCHET
61PASSENGER CENTER MOUNTING BRACKET TORQUE WRENCH
71DRIVER REAR MOUNTING BRACKET
81PASSENGER REAR MOUNTING BRACKET
912 M8 HEX HEAD CAP SCREW
10 12 M8 SPLIT LOCK WASHER
11 12 M8 FLAT WASHER
12 12 M10 HEX HEAD CAP SCREW
13 12 M10 BELLVILLE WASHER
14 12 M10 SERRATED FLANGE NUT
ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING
CONTENT
OUTLAW NERF STEP BARS
APPLICATION:
2005-2019 Toyota Tacoma Double Cab
PART NUMBER:
58-52775
Passenger Side Opposite
ITEM 1 ITEM 3
ITEM 4 ITEM 5 ITEM 6 ITEM 7 ITEM 8

2
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5852775-RevA ECO #: W18-0157 DATE: 04/16/19
PROCEDURE
1. Remove contents from box, verify if all parts listed are present and free from damage.
Carefully read and understand all instructions before attempting installation.
Failure to identify damage before installation could lead to a rejection of any claim.
2. Start installation on either side of the vehicle. Locate mounting locations with factory threaded holes with caps covering
them. Remove factory caps from threaded holes, they will not be used again. Locate (1) Front Mounting Bracket and
loosely install it to the front mounting location on the rocker panel using (2) Long M8 hex head cap screw, (2) M8 split
lock washer, and (2) M8 flat washer. Locate the Center and Rear Mounting Brackets (Item 3) and loosely secure in the cor-
rect mounting locations on the rocker panel. Loosely install using the provided M8 hardware. See Figure. 1 and 2.
3. Repeat Step 2 for the other vehicle side.
Fig 1 Fig 2
11
10
9
9
10
11
Installation similar for all
Center and Rear Locations
4. For step bar installation, use the supplied M10 Hardware to loosely secure the step bar to the preinstalled brackets. See
Figures 3 & 4. Note: All brackets install similarly to step bar.
5. Align and adjust the step bars and brackets as needed, then fully tighten all hardware: M8 to 18 ft-lbs, M10 to 38 ft-lbs.
Fig 3
Fig 4

3
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5852775-RevA ECO #: W18-0157 DATE: 04/16/19
CARE INSTRUCTIONS
 REGULAR WAXING IS RECOMMENDED. DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES.
 STAINLESS STEEL PRODUCTS CAN BE CLEANED WITH MILD SOAP AND WATER. STAINLESS STEEL POLISH SHOULD BE USED TO POLISH SMALL SCRATCHES.
 GLOSS BLACK FINISHES SHOULD BE CLEANED WITH MILD SOAP AND WATER
Driver Side Shown
INSTALLATION COMPLETE
Front
ITEM 7 ITEM 5
ITEM 3
Front
ITEM 4 ITEM 6
ITEM 8
Passenger Side Shown

4
Westin Automotive Products, Inc.
320 W. Covina Blvd
San Dimas, Ca. 91773
Thank you for choosing Westin products
for additional installation assistance please call
Customer Service [phone]
www.westinautomotive.com
P.N.: 75-5852775-RevA ECO #: W18-0157 DATE: 04/16/19
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
WARNING
Failure to follow these instructions could lead to death, personal injury, and / or property damage.
FASTENERS:
All Westin supplied fasteners must be utilized and installed in accordance with the installation in-
structions and apply torque to the specifications as defined. DOUBLE CHECK ALL FASTENERS
BEFORE INITIAL USE, AND PERIODICALLY IN THE FUTURE TO ENSURE PROPER FUNCTION
AND SAFETY.
DRILLING:
Most Westin products do not require drilling for installation. If drilling is defined as required, use
caution when drilling a vehicle. FAILURE TO REVIEW AN AREA TO BE DRILLED MAY RESULT IN
PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL AS VEHICLE DAMAGE.
EYE PROTECTION:
ALWAYS WEAR SAFETY GLASSES OR GOGGLES DURING THE INSTALLATION PROCESS TO
AVOID PERSONAL INJURY.
MAXIMUM TOWING/CARRYING CAPACITY: (if applicable)
The Westin Receiver Hitches will have a visible tow rating label affixed directly on the product.
User should never exceed the vehicle manufacturers maximum tow and weight rating regardless
of the capacity of the hitch. FAILURE TO FOLLOW THESE GUIDELINES WILL VOID THE WESTIN
WARRANTY AND MAY RESULT IN PERSONAL INJURY AND/OR INJURY TO OTHERS AS WELL
AS VEHICLE DAMAGE.
FOR CALIFORNIA RESIDENTS ONLY-PROP 65 WARNING:
Some products may contain chemicals such as DEHP, which can cause cancer, birth defects or
other reproductive harm. For more info go to www.p65warnings.ca.gov