Whelen Engineering Company IS3 Series User manual

REPLACEM
ENT PARTS
FOR IS3
SERIES
STROBES
ENGINEERING COMPANY, INC
IS3 SERIES
STROBE LIGHT BEACONS
IS3006, 10-40 VDC, 12-28 VAC, SINGLE FLASH
IS3010, 12/24 VOLTS DC, DOUBLE FLASH
IS3020, 12/24 VOLTS DC, DOUBLE FLASH
IS3210, 120 VOLTS AC, SINGLE FLASH
IS3220, 120 VOLTS AC, DOUBLE FLASH
IS3240, 240 VOLTS AC, DOUBLE FLASH
Doc No. 04-0113059-01
Route 145, Winthrop Road
Chester, Ct 06412-0684
TELEPHONE: [phone]
TOLL FREE: 1-800-637-4736
1996 Whelen Engineering Company, Inc. Doc No. 04-0113059-01
January 25, 1996. 13059D
WARNING...
DISCONNECT THE
POWER SOURCE AND
WAIT 10 MINUTES
BEFORE INSTALLING
OR SERVICING THE
STROBE LIGHT.
DOME
STROBE TUBE ASSEMBLY
STROBE POWER SUPPLY
MOUNTING SCREW
BASE
BASE GASKET
SEE OTHER SIDE
OF PAGE FOR
REPLACEMENT
PARTS LISTING.

ITEM QTY PART NUMBER IS3010 IS3020 IS3210 IS3220 IS3240 IS3006
DOME, HIGH PROFILE, AMBER 168-2180483-10 n n n n n n
DOME, HIGH PROFILE, BLUE 168-2180483-20 n n n n n n
DOME, HIGH PROFILE, CLEAR 168-2180483-30 n n n n n n
DOME, HIGH PROFILE, GREEN 168-2180483-40 n n n n n n
DOME, HIGH PROFILE, RED 168-2180483-50 n n n n n n
DOME, LOW PROFILE, AMBER 168-2180452-10 n n n n n n
DOME, LOW PROFILE, BLUE 168-2180452-20 n n n n n n
DOME, LOW PROFILE, CLEAR 168-2180452-30 n n n n n n
DOME, LOW PROFILE, GREEN 168-2180452-40 n n n n n n
DOME, LOW PROFILE, RED 168-2180452-50 n n n n n n
STROBE TUBE ASSEMBLY KIT 101-0441566-00 n n n
STROBE TUBE ASSEMBLY KIT 101-0441567-00 n n n
POWER SUPPLY ASSEMBLY 102-0167214-00 n
POWER SUPPLY ASSEMBLY 102-0167204-00 n
POWER SUPPLY ASSEMBLY 102-0167273-00 n
POWER SUPPLY ASSEMBLY 102-0167163-00 n
POWER SUPPLY ASSEMBLY 102-0168643-00 n
POWER SUPPLY ASSEMBLY 102-0168568-00 n
WIRING INSTRUCTIONS
MODELS IS3006, IS3010 and IS3020
NOTE: A fuse is recommended in the Positive (+)
line wire (RED wire).
Model IS3006: 3 amp fuse is recommended.
Model IS3010: 3 amp fuse is recommended.
Model IS3020: 6 amp fuse is recommended.
1. Connect the RED wire to positive DC volts (+).
2. Connect the BLACK wire to DC ground (-).
(For AC powered IS3006 polarity does not matter.)
MODELS IS3210 and IS3220
1. Connect the GREEN wire to the AC service green
wire (ground).
2. Connect the BLACK wire to the AC service black
wire (hot).
3. Connect the WHITE wire to the AC service white
wire (neutral).
NOTE: A fuse may be used in the AC Hot wire.
Model IS3210: 1 amp fuse is recommended.
Model IS3220: 2 amp fuse is recommended.
MODELS IS3240
1. Connect the GREEN wire to the AC service green
wire (ground).
2. Connect the BLACK wire and the WHITE wire to
the AC service.
MOUNTING INSTRUCTIONS
1” PIPE MOUNT.
The IS3 series strobe beacon features a combination
base which may be used for either 1 Inch (NPT) Pipe
Mount or Permanent Mount/.
The threading for the 1” NPT is precast in the base.
1. Feed the power cable through the 1 inch pipe and
connect the cable to the wires of the IS3 .
2. Screw the strobe beacon to the threads on the 1”
pipe, taking precaution not to damage the wires.
Note: Do not damage the pipe threads on the
polycarbonate base by over tightening.
PERMANENT MOUNT
1. Use the base as a template and mark the three
mounting holes on the mounting surface. After
removing the base, mark a wire access hole in the
center of the three mounting holes.
2. Drill mounting holes in the mounting surface to fit
#10 mounting screws supplied with the strobe
beacon. drill the wire access hole using a 3/8” drill.
Deburr the wire access hole.
3. After connecting the strobe beacon to the power
cable, feed the wires through the access hole and
place the base (with the gasket, if required) on the
mounting surface. Secure the beacon with three #10
screws.
1996 Whelen Engineering Company, Inc. Doc No. 04-0113059-01 January 25,
1996.