Whitehall Para-Therapy PT-6-S Operation and maintenance manual

PT-6-S
PT-18-S
Para-Therapy™
Revised: April 2017
5900-100-000
INSTRUCTIONS FOR
OPERATION AND CARE OF
800-782-7706 • 626-968-6681 • www.whitehallmfg.com
P.O. Box 3527 • City of Industry, CA, 91744-0527, U.S.A.
Division of
®
Acorn Engineering Company
®

WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
a
CAUTION
DANGER
AVANT DE CONNECTER,
LIRE LES INSTRUCTIONS
! !
BEFORE CONNECTING,
READ INSTRUCTIONS
Grounding reliability can only be achieved when the
equipment is connected to an equivalent receptacle
marked “Hospital Only” or “Hospital Grade”.
Medical Equipment:
With respect to electric shock, fire and mechanical
hazards only in accordance with UL 60601-1 and CSA
C22.2 No. 601.1
La mise à terre ne fonctionne de facon efficace que si l’
équipment est connecté à une prise marquee “Hopital
Seulement” ou “Categorie Hopital”.
Équipement Médical:
Concernant les risques de chocs électriques de feu et
autres dangers mecaniques seulement conformément a
UL 60601-1 et a CSA C22.2 No. 601.1
WARNING
Risk of explosion if used in the presence of flammable
anesthetics
lREPLACE fuse as marked
lOuter Surface is Hot
lAVOID Prolonged skin contact.
lAVOID resting objects on or against the tank.
Risque d’ explosion si utilisé en présence d’
anesthisques inflammables
lREMPLACER les fusibles tel qu’ indiqué
lLa surface extérieure est chaude
lÉVITER tout contact prolongé avec la peau.
lÉVITER de deposer des objets sur le reservoir ou de
les appuyercontre celui-ci.
lRETIRER tout emballage, accessoire et feuillet se
trouvant à l'intérieur de votre nouvel appareil avant de
l'utiliser.
EFFECTUER LA MISE À LA TERRE de votre
appareil DE FAÇON APPROPRIÉE. Brancher
l'appareil dans une prise à disjoncteur différentiel de
fuite à la terre (DDFT), ce qui offre une protection au
cas où l'eau et la paraffine entreraient en contact
avec l'électricité. Si l'appareil n'est pas bien mis à la
terre, cela augmente les RISQUES DE DÉCHARGES
ÉLECTRIQUES !
lNE JAMAIS utiliser l'appareil en prenant un bain ou
près de l'eau. RISQUE DE DÉCHARGES
ÉLECTRIQUES !
lNE JAMAIS utiliser l'appareil près de liquides ou de
gaz combustibles. RISQUE D'EXPLOSION !
ÉVITER DE TOUCHER LE FOND DU RÉSERVOIR.
Le fond peut être plus chaud que la paraffine en
raison de l'emplacement des éléments chauffants.
l
l
FOR PROFESSIONAL USE ONLY POUR PROFESSIONEL USE SUELEMENT
ATTENTION
DANGER
AVERTISSMENT
lPROPERLY GROUND your unit. Plug unit into a
Ground Fault Circuit Interrupter (GFCI) receptacle for
safety. Failure to properly ground unit can increase
the risk of ELECTRICAL SHOCK HAZARD!
lREMOVE all packaging, accessories and literature
from inside of unit prior to using.
lNEVER use unit while bathing or near water.
ELECTRICAL SHOCK HAZARD!
lNEVER use unit in the presence of combustible
liquids or gases. EXPLOSION HAZARD!
lAVOID TOUCHING BOTTOM OF TANK. Bottom can
be hotter than paraffin due to heating element
location.

1
Table of Contents
General Warning .............................................................................................................Page a
Equipment Description ....................................................................................................Page 2
Operating Instructions .....................................................................................................Page 3
Operating Tips .................................................................................................................Page 3
Treatment Tips.................................................................................................................Page 4
Paraffin Replacement and Cleaning................................................................................Page 4
Electrical Diagrams and Specifications
Model PT-6-S ..........................................................................................................Page 6
Model PT-18-S ........................................................................................................Page 8
Repair Parts
Model PT-6-S ..........................................................................................................Page 6
Model PT-18-S ........................................................................................................Page 8
Exploded View
Model PT-6-S ..........................................................................................................Page 7
Model PT-18-S ........................................................................................................Page 9
Troubleshooting Guide ..................................................................................................Page 10
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 USA
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
Instructions for Operation and Care of Paraffin Baths

Stationary Paraffin Tanks provides a simple, effective method of applying heat to the surface of body
extremities where conditions indicate a need for increased circulation. The tank shall be for an arm or
hand paraffin bath.
Indications;
Paraffin bath, when prescribed, is a useful method of relieving pain caused by medically diagnosed
arthritis, bursitis and chronic joint pain. Relaxes muscles, relieves muscle stiffness, and muscle
spasms. Most commonly used prior to therapeutic exercise and or massage. Consult your physician if
you have any questions.
Contraindications;
Should not be used in the presence of open wounds, inflammatory skin conditions, growths, peripheral
vascular disease where circulation is impaired, acute inflamation, or when there is reduced or absent of
sensation of the extremities (such as in some cases of diabetes). Should not be used on areas subject
to hemorrhaging or in cases involving abdominal sensitivity to heat. Discontinue use if dermatitis occurs
due to sensitivity to paraffin wax or if wax feels too hot or cold, could indicate health problems with user.
Consult with a physician or physical therapist before using.
Model PT-6-S Specification:
Overall Dimensions: 13" L x 7" W x 7-3/4" D (330 L x 180 W x 195 D)
Inner Tank Dimensions: 11-3/4" L x 5-3/4" W x 5-3/4" D (300 L x 145 W x 145 D)
Tank Capacity: 6 lbs. (2.72 kgs.)
Electrical Requirements: Inlet Voltage 120 VAC
Frequency 50/60 Hz
1 Amp
Power Output 0.12 kW
Model PT-18-S Specification:
Overall Dimensions: 21" L x 13" W x 8-1/4" D (535 L x 330 W x 210 D)
Inner Tank Dimensions: 19-3/4" L x 11-1/2" W x 5-3/4" D (500 L x 290 W x 145 D)
Tank Capacity: 18 lbs. (8.16 kgs.)
Electrical Requirements: Inlet Voltage 120 VAC
Frequency 50/60 Hz
3 Amp
Power Output 0.36 kW
Instructions for Operation and Care of Paraffin Baths
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
2
Equipment Description
ACCEPTABLE TRANSPORTATION AND
STORAGE CONDITIONS:
Temperature: +32 ºF to +131 ºF (0 ºC to +55 ºC)
Relative Humidity: 10% to 100%
Atmospheric Pressure: No Requirements
Note: Unit must not be exposed to ingress of water
or to severe physical trauma. Degradation of unit
function and/or performance may occur.
CONDITIONS ACCEPTABLES CONCERNANT LE
TRANSPORT ET L'ENTREPOSAGE:
Température : à + ( à +55 ºC)
Humidité relative : 10 % à 100 %
Pression atmosphérique : aucune exigence
Remarque : l'appareil ne doit pas être exposé à une
infiltration d'eau ou à un traumatisme physique grave.
Une détérioration des fonctions et/ou du rendement de
l'appareil peut en découler.
+32 ºF 131 ºF 0 ºC

Step 1– Remove your new Para-Therapy unit from its packaging and place unit on
a suitable level surface like a sturdy tabletop or countertop. Remove
stainless steel cover and remove any accessories and literature from
inside of tank.
NOTE: DO NOT PLUG UNIT IN UNTIL STEP 2 IS COMPLETED!
Step 2– Add paraffin to unit. For Model PT-6-S add six (6) one pound bags of
genuine Para-Therapy paraffin chips and for Model PT-18-S add eighteen
(18) one pound bags of paraffin chips. Chips sometimes melt together
during shipment but can be easily separated when putting in unit. (Note: If
you are using paraffin by others and it is not in chip form, but one pound
bars, make sure each bar is placed individually into unit so they come in
contact with the bottom of the tank so they will melt properly.)
Step 3– Your Para-Therapy unit is now ready to plug in. When unit is plugged in, the
indicator light on the front of unit will come on indicating unit is under power. The
six pound unit will take 4 to 5 hours and the eighteen pound unit will take 10 to
12 hours to melt all the paraffin completely. Once paraffin is completely melted
your unit is ready to use.
Operating Tips
When do I need to add Paraffin?
Add paraffin when the paraffin level in your tank drops below a depth of 3”. Using
unit without sufficient paraffin in the tank can cause major temperature fluctuations
in the paraffin bath.
Why is there foreign material on the bottom of the tank?
The material on the bottom of the tank is contamination such as dirt or dead skin
which builds up after prolonged use or by placing used paraffin back in the unit after
treatment. When this happens, we recommend removing used paraffin, cleaning
unit and adding new paraffin.
Why is there a film of solidified paraffin on the top surface of my tank?
The paraffin has lost some of its oil through normal usage. Add paraffin oil (food
grade mineral oil) as required or replace paraffin.
REMARQUE: NE PAS BRANCHER L'APPAREIL AVANT D'AVOIR
TERMINÉ L'ÉTAPE 2 !
3
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 USA
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
Operating Instructions
Instructions for Operation and Care of Paraffin Baths

1. Wash the area being treated thoroughly with anti-bacterial soap and water. Dry skin
thoroughly.
2. WARNING: Always check paraffin temperature before using your paraffin bath. The
proper treatment temperature ranges are 128º-136ºF / 53º-58ºC.
3. Slowly dip fingertips or toes into paraffin. Continue slowly until hand or foot is fully
immersed. If heat of paraffin is too intense for patient, paraffin can be cooled a few
degrees by removing cover from unit for a few minutes prior to treatment. (Unplugging
unit is not recommended to cool paraffin because paraffin will quickly begin to solidify on
the top surface if heater is not cycling.)
4. Once the extremity being treated is totally submerged, remove it from bath and re
immerse five to ten times to build up several layers of paraffin. (Patient may also keep
their hand or foot in the paraffin bath and enjoy the therapeutic heat.) NOTE: For
treating the back, knee, shoulder or other areas of the body which cannot be dipped
into the tank, a soft brush may be used to apply multiple layers of paraffin to area as
required for treatment.
5. For maximum benefit, after the paraffin has been applied to patient, wrap the area in
plastic sheeting (plastic bags work well for hands and feet) and cover with a towel. This
retains heat and provides the patient with 20 to 30 minutes o soothing therapy.
6. Once treatment is finished, remove towel and plastic wrap. Then peel off paraffin and
return it to tank. (NOTE: If more than one person is to use the unit, used paraffin should
be discarded and not returned to the tank!)
7. When unit is not in use, place cover back on unit and leave unit plugged in. This way
unit will be ready for future treatments.
MISE EN GARDE : Toujours vérifier la température de la paraffine avant d'utiliser votre
bain de paraffine. La bonne température pour les traitements varie de
53 ºC à 58 ºC/128 ºF à 136 ºF.
Instructions for Operation and Care of Paraffin Baths
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
4

1. Unplug unit and let paraffin solidify overnight. The next morning the paraffin should be a
solid block.
2. To remove solid block of paraffin from unit, plug unit back in for approximately 15 to 20
minutes. This will cause solid block of paraffin to begin to melt and separate from the
tank. Place a towel down on a sturdy flat surface, such as a table or countertop. Place a
plastic trash bag on top of the towel.
3. Take care not to over-melt paraffin. Remove lid and press one end of solid paraffin block
to check if paraffin has melted too much. If block moves down when you press down on
the paraffin solid block, the paraffin has melted too much and should be allowed to cool
and re-solidify. (If the following steps are performed and the paraffin has melted too
much, a spill could occur causing a mess and a safety hazard.)
4.Unplug unit and turn unit upside down, with the lid on, on top of the plastic trash bag
and towel. Carefully lift unit up an inch or two and then bump it down on the surface to
break free the solid paraffin block. Block should drop on to lid. Lift away unit leaving the
paraffin block on top of the lid. (Sometimes if the paraffin is low on paraffin oil, the block
may be required to melt a little longer to break free.)
5.Once the solid block has been removed from the tank it can be discarded or saved for
reuse if desired.
6. To remove any remaining paraffin remnants from the inside of the tank, hot water and
paper towels work best. Once all the remaining paraffin has been removed, wash inside
of unit with soap and water. Rinse and dry the inside of the tank.
7. After the unit has been cleaned, add new Para-Therapy Paraffin Refills as required to
inside of tank or reuse the solid block of paraffin you removed earlier by placing it back
in the tank the same way it came out.
8. Unit is now ready to be used.
5
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 USA
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
Instructions for Operation and Care of Paraffin Baths

PARA-THERAPY MODEL PT-6-S (120 VAC)
ITEM # PART # DESCRIPTION
1 5902-111-299 Lid
2 0322-003-000 #6 Plated Star Lockwasher
3 0302-010-000 #6 Stainless Steel Hex Nut
4 0710-457-000 Standard Temp. Thermostat
5 0710-456-000 Thermal Cutout
6 5902-110-001 Pan w/ Weld Studs (Assembly)
7 6505-504-000 Heating Element
8 0316-020-000 #10-32 Tinnerman Nut
9 0710-232-000 Fuse Holder Assembly
10 0710-224-000 1/4 x 1-1/4 2A Delay Ceramic Fuse
11 6505-546-000 Appliance Inlet
12 5903-113-001 Euro Outer Housing
13 6505-540-000 Indicator Light (250 VAC)
14 5902-113-199 Bottom Cover
15 6504-604-000 Snap-In Bumper (Foot)
16 0331-014-000 0.203 ID x 0.734 OD Stainless Steel Washer
17 0116-006-000 #10-32 x 1” Long Phillips Truss Head Screw
18 6505-056-000 Power Cord Set
19 5902-117-199 Side Insulation
20 5902-119-199 Bottom Insulation
21 5902-121-199 Heat Sink Bar Spacer
22 5902-120-199 Heat Sink Bar
23 0302-011-000 #6 Stainless Steel Hex Nut
Instructions for Operation and Care of Paraffin Baths
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
6

Parts Not Shown For Clarity
Side Insulation
Bottom Insulation
19
20
Exploded View
7
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 USA
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
Instructions for Operation and Care of Paraffin Baths
FUSE 1
FUSE 2
GND
INLET
L
N
THERMO-
INDICATOR
HEATING
ELEMENTS
LIGHT
STAT
THERMAL
CUTOUT
POWER
Electrical Specifications
Inlet Voltage: 120V AC
Frequency: 60Hz
Power Input: 0.12 kW
Mains Fuses: 2 x 4 Amps.
1/4” x 1-1/4” Time Delay
17
16
15
14
13
12
11
910
22
21
8
7
6
53
43
223
1
18
EXPLODED VIEW PT-6-S (120 VAC)

PARA-THERAPY MODEL PT-18-S (120 VAC)
1/4” x 1-1/4” Time Delay
18
ITEM # PART # DESCRIPTION
1 5902-211-199 Lid
2 0322-003-000 #6 Plated Star Lockwasher
3 0302-010-000 #6 Stainless Steel Hex Nut
4 0710-457-000 Standard Temp. Thermostat
5 0710-456-000 Thermal Cutout
6 5902-210-002 Pan w/ Weld Studs (Assembly)
7 6505-504-000 Heating Element
8 0710-232-000 Fuse Holder Assembly
9 0710-201-000 4 Amp Fuse
10 6505-546-000 Appliance Inlet
11 5903-213-001 Outer Housing
12 0316-020-000 #10-32 Tinnerman Nut
13 5902-213-199 Bottom Cover
14 6505-540-000 Amber Indicator Light (125 V)
15 0116-010-000 #10-32 x 1/2" Phillips Truss Head Screw
16 0302-004-000 #10-32 Hex Nut
17 6502-560-000 #10 Stainless Steel Lockwasher
6504-605-000 Cabinet Foot
19 0116-013-000 #10-32 x 3/4" Phillips Round Head Screw
20 0116-006-000 #10-32 x 1" Phillips Truss Head Screw
21 5902-217-199 Side Insulation
22 5902-219-199 Bottom Insulation
23 5902-121-199 Heat Sink Bar Spacer
24 5902-120-199 Heat Sink Bar
25 6505-056-000 Power Cord Set
Instructions for Operation and Care of Paraffin Baths
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
8

EXPLODED VIEW PT-18-S (120 VAC)
Parts Not Shown For Clarity
Side Insulation
Bottom Insulation
18
19
9
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 USA
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
Instructions for Operation and Care of Paraffin Baths
1
23
6
7
23
24
53
42
9
8
3
10
11
12
13
14
15
16
17
18
19
20
12
25
FUSE 1
FUSE 2
GND
INLET
L
N
THERMO-
INDICATOR
HEATING
ELEMENTS
LIGHT
STAT
THERMAL
CUTOUT
POWER
Electrical Specifications
Inlet Voltage: 120V AC
Frequency: 60Hz
Power Input: 0.12 kW
Mains Fuses: 2 x 4 Amps.
1/4” x 1-1/4” Time Delay

PARA-THERAPY TROUBLESHOOTING GUIDE
PROBLEM CAUSE SOLUTION
PARAFFIN WAX NOT MELTING NO POWER TO UNIT CHECK TO SEE UNIT IS PLUGGED INTO
INDICATOR LIGHT OFF WALL OUTLET, AND PROPERLY ATTACHED
TO APPLIANCE INLET.
CHECK FUSE BOX FOR WALL OUTLET.NO POWER FROM
WALL OUTLET
BURNT MAINS FUSE REPLACE BURNT FUSE.
PARAFFIN WAX NOT MELTING THERMAL CUTOUT IS CHECK THERMAL CUTOUT FOR CONTINUITY
INDICATOR LIGHT ON WITH MULTI-METER, IF NO CONTINUITY
REPLACE THERMAL CUTOUT.
BURNT OR FAULTY.
REPLACE THERMOSTAT.THERMOSTAT IS
BROKEN.
HEATING ELEMENT IS REPLACE HEATING ELEMENTS.
BURNT OR FAULTY.
PARAFFIN WAX IS MELTING INDICATOR LIGHT REPLACE INDICATOR LIGHT
INDICATOR LIGHT OFF BURNT OUT.
PARAFFIN IS TOO HOT PARAFFIN LEVEL TOO ADD PARAFFIN TO UNIT.
LOW.
THERMOSTAT IS REPLACE THERMOSTAT.
BROKEN.
PARAFFIN IS SOLIDIFYING AT PARAFFIN IS LOW ON ADD PARAFFIN OIL (FOOD GRADE MINERAL
TOP SURFACE OIL. OIL) TO PARAFFIN.
Instructions for Operation and Care of Paraffin Baths
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone [phone] • [phone] • Fax [phone] • Web: www.whitehallmfg.com
10

Mailing Address:
P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A
Physical Address:
15125 Proctor Avenue • City of Industry, CA 91746 U.S.A
Phone [phone] • 626-968-6681
Fax [phone]
Web: www.whitehallmfg.com
E-mail: [email protected]
Whitehall Manufacturing Company warrants that its products are free from defects in material or workmanship under
normal use and service for a period of one year from date of shipment. Whitehall's liability under this warranty shall be
discharged solely by replacement or repair of defective material, provided Whitehall is notified in writing within one
year from date of shipment, F.O.B. Industry, California.
This warranty does not cover installation or labor charges, and does not apply to materials which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of
the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Whitehall under this
warranty. Whitehall shall not be liable under any circumstances for incidental, consequential or direct charges caused
by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all other
warranties expressed or implied. Product maintenance instructions are issued with each fixture, and disregard or non-
compliance with these instructions will constitute an abnormal use condition and void the warranty. If you have any
questions or require technical assistance, please call 800-743-8219.
NOTICE TO KEEP ORIGINAL PACKAGING- Regarding warranty claims: customer must retain original packaging
for one year upon receipt of product. If packaging is discarded, it is the customer's responsibility to provide adequate
packaging. Any shipping claims that are a direct result of customer-provided packaging materials will be handled by
the shipper.
MANUFACTURER'S WARRANTY
Member of
E.U. / Middle East DistributorDistributor
Niva Medical Company • Olarinluoma 14 B, FI-02200 Espoo, Finland
®