Whittier Wood 2068CAFh User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 03/17
McKenzie Media
Consoles
GAC = Glazed Antique Cherry finish
CAF = Caffè finish
Assembly Instructions
IMPORTANT NOTES:
•For normal household use only. Not recommended for commercial use.
•Do not climb, sit or stand on this piece of furniture.
•Do not overload the drawers or shelves.
•Unload items before you move this unit.
•Handle the glass plates with care. Glass is fragile.
•This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
•Place heaviest items in the bottom drawers.
•Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
•Never allow children to climb or hang on drawers, doors or shelves.
•Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or oth
er safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Model #
2068GACh
2068CAFh
54"W McKenzie
Media Console
Model #
2069GACh
2069CAFh
64"W McKenzie
Media Console
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

2068GACh 2068CAFh 54"W McKenzie Media Console &
2069GACh 2069CAFh 64"W McKenzie Media Console
Parts List
2068GACh_2068CAFh_2069GACh_2069CAFh — Page 2 — 03/17
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
2068GACh
2068CAFh
2069GACh
2069CAFh
A
Top Assembly
1
1
Bb
Adjustable Shelf
2
2
C
Knob (attached)
7
7
Dg
#8 x 1-1/2" Machine Screw Tuscan (installed)
7
7
E
Drawer Face (installed)
6
6
F
Drawer Box (inserted)
6
6
G
16" Drawer Slides (pre-installed sets)
6
6
Ha
Door Frame
1
1
Ia
Door Glass (attached)
1
1
Jd
Case
1
1
L
Shelf Bracket (installed)
8
8
M
#6 x 1/2" Undercut Screw (inserted)
8
8
Nb
Removable Back (attached)
2
2
O
Door Glass Support Rail (attached)
2
2
P
Door Glass Support Stile (attached)
2
2
Q
#6 x 3/4" Flat Head Screw (inserted)
12
12
S
#6 x 5/8" Philtruss Screw (inserted)
16
16
U
Hinge (attached)
2
2
X
Small Adjustable Glide (installed)
4
4
Yg
#8 x 7/8" Black Lo-Profile Screw (inserted)
24
24
ZA
#8 x 1" Pan Head Screw (inserted)
4
4
ZB
#8 x 1-1/4" Pan Head Screw (inserted)
14
16
ZD
#8 x 1-1/4" Black Screw (inserted)
5
6

2068GACh 2068CAFh 54"W McKenzie Media Console &
2069GACh 2069CAFh 64"W McKenzie Media Console
Parts List
2068GACh_2068CAFh_2069GACh_2069CAFh — Page 3 — 03/17
Part
Description
Quantity
2068GACh
2068CAFh
2069GACh
2069CAFh
ZG
Drawer Stop (attached)
4
4
ZH
Turn Button (attached)
4
4
ZI
#6 x 5/8" Undercut Screw ZN (inserted)
0 (GAC)
12 (CAF)
0 (GAC)
12 (CAF)
ZJ
#6 x 1/2" Philtruss Screw (inserted)
36
36
ZK
#6 x 3/4" Philtruss Screw (inserted)
36
36
ZS
Insert Nut (inserted)
4
4
ZT
#8 x 1-3/8" Lo-Profile Screw (inserted)
6
6
ZV
Foot Bracket (attached)
1
1
ZW
Adjustable Glide (installed)
1
1
ZX
Tuscan Magnetic Lock & Plate
(pre-installed sets)
2
2
ZY
#6 x 5/8" Undercut Screw AB (inserted)
16 (GAC)
4 (CAF)
16 (GAC)
4 (CAF)
ZZ
#10 x 3/4" Pan Head Screw (inserted)
4
4
TS
Media Tipping Restraint (attached)
1 set
1 set
2068 shown in the illustrations.

2068GACh 2068CAFh 54"W McKenzie Media Console &
2069GACh 2069CAFh 64"W McKenzie Media Console
Assembly Instructions
2068GACh_2068CAFh_2069GACh_2069CAFh — Page 4 — 03/17
Tool Required: Phillips Screwdriver, Pencil.
1. Place the console at its final destination. Rotate the Adjustable Glides (X) found at the corners
of the unit and (ZW) at the bottom of the Center Foot until the unit is level. See Figure 1.
2. You may want to remove the Removable Backs (Nb) so that you can fit your media units into the
console more easily. To do so, unlock the Turn Button (ZH) as shown in Figures 2 and 2b. Slide
the backs away and place them off to the side. To put them back into place, slide the backs
behind the Drawer Stops (ZG) and position the Turn Button so that it is locked. See Figures 2a
and 2b.
ZG
ZH
Locked
Position
Fig. 2
Fig. 2b
Fig. 2a
Nb
Nb
ZH
ZG
Unlocked
Position
Fig. 1
ZW
X
X

2068GACh 2068CAFh 54"W McKenzie Media Console &
2069GACh 2069CAFh 64"W McKenzie Media Console
Assembly Instructions
2068GACh_2068CAFh_2069GACh_2069CAFh — Page 5 — 03/17
3. To move the Adjustable Shelves (Bb), remove the #6 x 1/2" Undercut Screws (M) and the
Shelves (Bb). Reposition the Shelf Brackets (L) to the desired positions, replace the shelf and
insert the screws. See Figures 3 and 3a.
Continued on Page 6
Fig. 3
M
L
Fig. 3a
Bb
Door removed for illustration purposes.

2068GACh 2068CAFh 54"W McKenzie Media Console &
2069GACh 2069CAFh 64"W McKenzie Media Console
Assembly Instructions
2068GACh_2068CAFh_2069GACh_2069CAFh — Page 6 — 03/17
Furniture Tipping Restraint Instructions
Before you begin this assembly, identify each part and make sure the quantities received match what is on this
list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following
list for its name and letter code.
Part
Description
Quantity
A
Cam Buckle and Short Strap (installed)
1
B
Plastic Bracket (installed)
1
C
1" x 1000mm Long Strap (installed)
1
D
#8 x 3" Pan Head Screw
2
E
#10 x 1" Oval Head Screw (inserted)
1
F
Washer
1
If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.
4. Decide where you want to place the piece of furniture in your room. Mark the baseboard with a
pencil mark directly behind the location where the tipping restraint is attached to your item.
Move the item away from the wall far enough to allow you to access the spot where the
baseboard meets the floor. Position the straps and Plastic Bracket (B) as shown in Figures 4
and 4a with the angled corners of the Plastic Bracket (B) firmly placed against the seam of the
baseboard and floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the
Plastic Bracket (B) into the seam below the baseboard where it meets the floor. See Figures 4
and 4a.
Fig. 4
Fig. 4a
Wall
Floor
D
Floor
Baseboard
D
x 2

2068GACh 2068CAFh 54"W McKenzie Media Console &
2069GACh 2069CAFh 64"W McKenzie Media Console
Assembly Instructions
2068GACh_2068CAFh_2069GACh_2069CAFh — Page 7 — 03/17
5. Move the item back into position against the wall and reach underneath the piece of furniture to
grasp the loop in the free end of the strap. Pull the free end of the strap until portion between
the Cam Buckle (A) and the back apron of the item is tight. See Figures 5 and 5a. If you need
to move the piece of furniture reach beneath and locate the buckle which connects the two
sections of the strap and depress the release lever, then pull on the section of strap that is
between the buckle and the back apron of the furniture until there is enough slack to allow you
to pull the item away from the wall.
Fig. 5a
Fig. 5
C
Wall
Floor