Wilson Electronics weboost AH100-PRO User manual

Installation Guide
Cell Signal Booster
AH100-PRO
A WILSON ELECTRONICS BRAND
NEED HELP? BoltonTechnicalAfrica.com+27796793305

Package Contents 1
Preparation 2
STEP 1: Connect Inside Antenna To Booster 3
STEP 2: Mount & Point Outside Antenna Toward Nearest
Cell Tower 4
STEP 3: Route & Connect Cable To System 7
STEP 4: Power Up The Booster & Optimize System 8
Measuring Booster Performance 10
Light Patterns 12
Troubleshooting 13
Safety Guidelines 14
Specifications 17
Warranty Back Page
______
Index

1
SINGLE ROOM CELL PHONE SIGNAL BOOSTER
______
Package
Contents
Outside Antenna Options
Inside Antenna Options
In All Kits
Outside
Yagi Antenna
Wall Mount
Panel
AM100
Booster
Outside
Omni Antenna
Dome Antenna
Power
Supply
Roof/Pole
Mount
Bracket
Wall Mount
Bracket
2 Coax Cables
(1 x 10m; 1 x 5m)

2CELL PHONE SIGNAL BOOSTER SINGLE ROOM
______
Preparation
You Will Need (tools not included)
Make sure the following materials are prepared and ready for your
installation.
oLadder
oPhillips-head screwdriver
o10mm open-end wrench or adjustable wrench
oDrill (if routing cable through wall)
o3-5cm diameter pole existing pole (or order BT512631)
oRecommended: Power Strip with surge protection
1 to 2 hours
2 people (a person to help with antenna calibration)

3
SINGLE ROOM CELL PHONE SIGNAL BOOSTER
45 cm Apart
POWER
INSIDE
ANTENNA
______
Step 1-A & B: Connect Inside
Antenna To Booster
Connect Inside Antenna cable to the bottom port on AH100-PRO
booster labeled ‘INSIDE’ and place Inside Antenna in weak signal area at
least 45 Centimeters away from booster.
NOTE: Do not connect booster to power until the system is fully installed.
Inside
Antenna
Booster

4CELL PHONE SIGNAL BOOSTER SINGLE ROOM
______
Step 2: Mount & Point
Outside Antenna Toward
Nearest Cell Tower
Locate your cell towers by using apps such as ‘Network Cell Info Lite’ or
‘Open Signal’. This is a critical step of the installation process because
it will determine the overall performance of the booster system. Point
the Outside Antenna toward the nearest cell phone tower if using a Yagi
directional antenna.
Cell Tower
Outside Antenna
NOTE: The Outside Antenna must be at least
15 meters horizontal or 6 meters vertical from the
Inside Antenna for best performance. Make sure the
Inside Antenna and Outside Antennas are setup so
they are facing away from each other.
f
a
c
i
n
g
a
w
a
y

5
SINGLE ROOM CELL PHONE SIGNAL BOOSTER
If using an omni-directional antenna, ensure that antenna is placed on
highest point on roof for optimal broadcasting and reception.
NOTE: Mounting on existing roof pipe would
be a good time-saver option. eg. satellite dish pole.
______
(STEP 2 cont.)
Cell Tower
Outside Antenna
Pole Mounting Option

6CELL PHONE SIGNAL BOOSTER SINGLE ROOM
______
(STEP 2 cont.)
Drill holes using
3/16 inch bit
Tap anchors in
Fasten bracket to back
of Outside Antenna Secure bracket to wall
mounting
Outside Antenna
on wall bracket
sideview
Wall Mounting Option
______
Step 2-B Cont. Installing the
indoor wall panel

7
SINGLE ROOM CELL PHONE SIGNAL BOOSTER
______
Step 3: Route & Connect
Cable To System
Connect the LMR240 Cable to Outside Antenna and route cable into
the home. All connections should be hand tightened only.
A Window Entry Cable is available as an optional extra purchase.
Outside
Antenna Inside
Antenna
LMR240 Cable
Booster
Inside
Antenna
Outside
Antenna
Cell
Tower
Booster

8CELL PHONE SIGNAL BOOSTER SINGLE ROOM
______
Step 4: Power Up The
Booster & Optimize the
System
5
0
F
E
E
T
H
O
R
I
Z
O
N
T
A
L
O
R
2
0
F
E
E
T
V
E
R
T
I
C
A
L
D
I
S
T
A
N
C
E
5
0
F
E
E
T
H
O
R
I
Z
O
N
T
A
L
O
R
2
0
F
E
E
T
V
E
R
T
I
C
A
L
D
I
S
T
A
N
C
E
Plug the Power Supply into wall outlet then connect to AH100-PRO booster.
Outside
Antenna
Outside
Antenna
Cell
Tower
Inside
Antenna
RG-6 Cable RG-6 Cable
Window
Entry Cable
Booster
to power
Inside
Antenna
Power Supply
Window Entry Cable
15 METERS HORIZONTAL OR
6 METERS VERTICAL DISTANCE
Booster
Warning: Do Not connect power
supply to booster before connecting
both outside and indoor antennas