Wilson Electronics weboost DRIVE REACH OTR FLEET User manual

ENGLISH
FRANÇAIS
Installation Guide
Cell Signal Booster For Fleet Trucks
DRIVE REACH OTR FLEET
A WILSON ELECTRONICS BRAND
NEED HELP? weboost.ca 1.866.294.1660
®

______
Index
Package Contents 1
STEP 1: Select Mounting Location 2
STEP 2: Assemble The Antenna 3
STEP 3: Mount Outside Antenna 5
STEP 4: Mount Inside Antenna 7
STEP 5: Connect Coax Cables To Booster 8
STEP 6: Connect Power Supply To Booster 9
Light Patterns 10
Troubleshooting 11
Safety Guidelines 12
Specifications 14
Warranty 15

DRIVE REACH OTR FLEET CELL SIGNAL BOOSTER 1
ENGLISH
________
Package
Contents
Booster
& Bracket
Outside
Antenna
Inside
Antenna
Power
Supply
33 cm & 45.7 cm
Mast Extensions
& Side Exit Adapter
3-Way Antenna
Mount
Antenna
Spring
Thread
Lock
Cable
Adapter

2CELL SIGNAL BOOSTER DRIVE REACH OTR FLEET
ENGLISH
______
Step 1: Select Mounting
Location
Depending on the type of truck, there may be built-in antenna
mounting points. If the vehicle does not have built-in mounting
points, the outside antenna includes a 3-way mount that will
work on vehicles with mirror rails. The outside antenna will also
work with third party CB antenna mounts.
Select mounting location on vehicle. The outside antenna
can be mounted in any CB mount or antenna mounting point
on the vehicle. For best performance mount the outside
antenna above the metal cab (it does not need to be above
cab wind deflector).
Typical Antenna
Mounting Points
NOTE: Mount at least 12 inches from any other antennas. Free of obstructions.
NOTE: If the vehicle is using two CB antennas with co-phase wiring, removing
one antenna will cause reduced performance of the remaining CB antenna.

DRIVE REACH OTR FLEET CELL SIGNAL BOOSTER 3
ENGLISH
______
Step 2: Assemble The
Antenna
Mast
Extension
Mast
Extension
Mast
Extension
OR
Outside
Antenna
Side Exit
Adapter
cable
cable
from Outside
Antenna
Outside
Antenna
Once you have determined the
best location for the outside
antenna and have determined
if mast extensions are needed,
insert cable through mast.
If using mast extension(s) add
thread locker (provided) to thread
point(s). Screw into place.
Add thread locker (provided) to
thread point and screw on the
side exit adapter.
NOTE: Mast extensions may not be
needed depending on your mounting
point.
NOTE: Be sure the antenna is the correct
height before applying thread locker.
NOTE: When adding the side exit adapter
hold the outside antenna vertically and
screw the side exit adapter from the
bottom up. This reduces cable twisting.

4CELL SIGNAL BOOSTER DRIVE REACH OTR FLEET
ENGLISH
______
(STEP 2 cont.)
c
a
b
l
e
c
a
b
l
e
c
a
b
l
e
13 in.
Mast
13 in.
Mast 13 in.
Mast
18 in.
Mast
Side Exit
Adapter
Antenna Spring
(can be used
optionally)
DO NOT USE
Antenna Spring
with 2 Mast Extensions

DRIVE REACH OTR FLEET CELL SIGNAL BOOSTER 5
ENGLISH
______
Step 3: Mount Outside
Antenna
The cable is strong enough
that it may be shut in most
vehicle doors without
damaging the cable.
These are some typical antenna mounting points. If the vehicle
does not have built-in mounting points, a 3-way mount is
included that will work on vehicles with mirror rails.
3-Way
Antenna Mount
Mount disc washer
with lip in the
DOWN position
Fasten nut with lip
in the UP position
mirror rail
or bird perch mount
Side Exit
Adapter
Mast
Top of Mirror Mirror ArmUpper Side
3-Way Mount
on bird perch

6CELL SIGNAL BOOSTER DRIVE REACH OTR FLEET
ENGLISH
______
(STEP 3 cont.)
Side Exit Adapter must be
used with Antenna Spring
Add thread lock on
all threads with tube
provided
Mount disc washer with
lip in the DOWN position
Fasten nut with lip in
the UP position
If installing with the antenna spring, assemble the 3-way
mount as shown below.
Side Exit
Adapter
Antenna
Spring

DRIVE REACH OTR FLEET CELL SIGNAL BOOSTER 7
ENGLISH
______
Step 4: Mount Inside Antenna
Identify a place to mount the inside antenna, either on the side
of the seat or on the dash and mount. The location should be
at least 46 cm but no more than 91 cm from where the cellular
device will be used. Use the Velcro® adhesive strip/adhesive
strip provided and attach to desired location.
Inside
Antenna
Inside
Antenna
Velcro®
Velcro®

8CELL SIGNAL BOOSTER DRIVE REACH OTR FLEET
ENGLISH
______
Step 5: Connect Coax Cables
To Booster
Fasten adapter to end of cable from the outside antenna and
connect to the port labeled “Outside Antenna” on the Drive
Reach booster.
Connect the cable from the in-vehicle antenna to the port
labeled “Inside Antenna” on the booster.
from Outside Antenna
from Inside Antenna
NOTE: Bracket can be used to fasten booster in a specific location if desired.
bracket
Drive Reach