Wilson Electronics weboost Office 200 User manual

Installation Guide
Cell Signal Booster
A WILSON ELECTRONICS BRAND
NEED HELP? https://www.signalbooster.com 855.846.2654

Package Contents 1
Preparation 3
STEP 1: Inside Antenna & Booster Placement 5
STEP 2: Mount Outside Antenna 6
STEP 3: Route & Connect Outside Antenna To Booster 7
STEP 4: Route & Connect Inside Antenna To Booster 8
STEP 5: Power Up The Booster 9
Measuring Booster Performance 10
Menu System 12
Troubleshooting 16
Safety Guidelines 17
Specifications 19
Warranty 20
______
Index

1
OFFICE 200 CELL PHONE SIGNAL BOOSTER
______
Package
Contents
Office 200
Booster
Office 200
Booster
Power
Supply
(850026)
Power
Supply
(850026)
Lightning Surge
Protector
(859902)
Lightning Surge
Protector
(859992)
Cable Mounting
Clips
Cable Mounting
Clips
Inside
Antenna
(314407)
Inside
Antenna &
Connector
(314407)
Outside
Antenna
(314422)
Outside
Antenna
(314423)
75’ & 60’
Wilson 400 Cables
(952360 & 952375)
75’ & 60’
RG-11 Cables
(951160 & 951175)
2’ Wilson 400
Cable
(952302)
2’ RG-11
Cable
(951127)

2CELL PHONE SIGNAL BOOSTER OFFICE 200
______
Key Features
Extended Dynamic Range (XDR) for continuous
connectivity:
any incoming signal and never shuts down due to a
strong outside signal.
Simple Wall-Mount Installation: An indoor and outdoor
port are located on top of the amplifier for easy antenna
connections, while an exposed mounting flange at each
corner of the amplifier provides for simple and clean wall-
mount installation.
Onboard Software for Better Control: The amplifier is
automatically controlled with automatic onboard software,
ensuring great connectivity throughout large spaces and
multi-story buildings. The amplifier will adjust its gain
level up or down as required by the conditions of the
immediate signal environment.
Color LCD Touch Screen:
LCD touch screen for assessing amplifier performance,
making adjustments to the outside antenna, and turning

3
OFFICE 200 CELL PHONE SIGNAL BOOSTER
______
Preparation
You Will Need (tools not included)
Make sure the following materials are prepared and ready for your installation.
Ladder
Drill
1” - 2” diameter existing pole for mounting
Outside Antenna (#901117 Pole Mount can be
purchased separately if needed)
Recommended: Power Strip with surge protection
1 to 2 hours

4CELL PHONE SIGNAL BOOSTER OFFICE 200
______
Installation Diagram
Outside
Antenna
Booster
75’ Coax Cable
Troubleshooting section recommends increasing distance
further if needed.
60’ Coax Cable
to power
Lightning Surge
Protector
Inside
Antenna
60 FEET HORIZONTAL OR 25 FEET VERTICAL DISTANCE
G
r
o
u
n
d

5
OFFICE 200 CELL PHONE SIGNAL BOOSTER
AT LEAST 24” APART
Plastic Nut
Tab Ring
ceiling mount
drywall
NOTE: Do not connect booster to power until the system is fully installed.
______
Step 1: Inside Antenna &
Booster Placement
Place the inside antenna in the ceiling over where you need the greatest signal
boost and place booster in your desired location at least 24” away from
inside antenna.

6CELL PHONE SIGNAL BOOSTER OFFICE 200
______
Step 2: Mount Outside Antenna
NOTE: Mounting on existing roof exhaust pipe would be a good time-saver option. Watch
out for power lines.
Pole mounting and wall mounting options are included.
Attach the mount to the outside antenna and use the bracket clamp to attach
the antenna to a pole or exhaust pipe.
Outside
Antenna
U-Bolt
L-Bracket
existing
pole
Pole
Bracket

7
OFFICE 200 CELL PHONE SIGNAL BOOSTER
______
Step 3: Route & Connect
Outside Antenna To Booster
Route cable to the and connect to the port labeled
‘OUTSIDE ANTENNA’.
Outside
Antenna
75’ Coax Cable 2’ Coax Cable
Outside
Antenna
Lightning Surge
Protector
Booster
Booster
Cable Mounting Clips
provided
Lightning Surge
Protector
Connect 2 ft. coax cable to outside antenna, attach the lightning surge
protector, then connect the black 75 ft. coax cable and route into building.
G
r
o
u
n
d

8CELL PHONE SIGNAL BOOSTER OFFICE 200
______
Step 4: Route & Connect
Inside Antenna To Booster
Inside
Antenna
60’ Coax Cable
Booster
Connect the black 60 ft. coax cable to inside antenna and route to the
200 booster and connect to the port labeled ‘INSIDE ANTENNA’.
Outside
Antenna
Booster
Cable Mounting Clips
provided
Inside
Antenna