WilTec 61059 User manual

Operation Manual
Ceramic Fan Heater
61059
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

© by WilTec Wildanger Technik GmbH Item 61059 Page 2
http://www.WilTec.de
http://www.aoyue.eu 07 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: [e-mail]
Tel:[phone]
Fax: [phone]
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [email protected]o
Tel:[phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 61059 Page 3
http://www.WilTec.de
http://www.aoyue.eu 07 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
Intended use
This product is only intended for indoor use in offices and private homes and not for application outside
or within an industrial or commercial environment. Only use this product with a faultless electric wiring
conforming to the ordinance of your local ordinances. In case of questions concerning the adequacy of
your wiring, consult a qualified electrician.
Safety instructions
While using this device, please abide to the following rules and regulations in order to prevent accidents
potentially leading to the device sustaining damage, severe injuries or even death.
•Do not use this heater without a functioning smoke detector located nearby and only use it as
described in this manual as any usage not recommended by the manufacturer may cause harm
to people and property.
•Do not operate the heater if the power cord has been damaged or if the device has been
dropped in any manner, and immediately stop it in case of malfunction.
•Do not leave this device unattended once it has been turned on.
•Children and individuals without the proper experience and knowledge or reduced physical,
mental or sensory abilities are not allowed to use, maintain or clean this heater unless they have
been properly instructed and are supervised by a knowledgeable person responsible for their
safety.
•Do not place the heater on carpets, uneven or unstable surfaces or where it may tilt or fall.
•In order to guarantee the proper functionality of this device, place it upon a stable, smooth and
non-combustible surface that offers sufficient space.
•Always make sure to unplug the heater when it is not in use.
•Do not operate the heater with any of its safety devices removed.
•Do not use extension cords as they may overheat and cause fires.
•Do not place the power cord beneath carpets or cover it with other items, and make sure to
place it in a way that will not cause people to trip over it.
Electrical hazard
Only use the heater in dry environments; this product is not intended for usage in damp or moist areas,
such as bathrooms, laundry areas, near sinks, washing machines, swimming pools or other sources of
water and moisture. Never place the heater near containers of water into which it might fall. Do not use
this product outdoors either.
This product is equipped with a polarised plug that, as a safety precaution, has been designed to only
fit into polarised outlets in a specific way. Therefore, always make sure to match the plug accordingly.
In case of the plug not properly fitting into the outlet consult a qualified electrician.
Do not use this device if either the power cord or the plug is damaged. Always make sure to use func-
tioning parts that are in perfect condition and thus safe to use. Do not operate the device if it shows any
visible sign of damage or has malfunctioned before. For further information concerning repairs under
warranty please see the warranty statement delivered along with the product.

© by WilTec Wildanger Technik GmbH Item 61059 Page 4
http://www.WilTec.de
http://www.aoyue.eu 07 2021-1
http://www.teichtip.de
Fire hazard
Do not use the heater near combustible materials, flammable gases, other heat sources, or in areas
where these are stored. Further ensure to keep a safety distance of at least 1 m (approx. 3.2 ft) in all
directions from the device before operating the same and make sure that the air can freely circulate in
order to prevent possible fires. Never place the device on soft surfaces, such as beds, as openings
might get blocked.
Do not insert or allow objects to be inserted into the ventilation as this might lead to electric shocks, fire,
or damage to the heater. Never use extension cords as they may overheat and thereby cause fire.
Always make sure to unplug the device when it is not in use.
Burn hazard
Neither touch the heater while it is running nor shortly afterwards as its frame heats up during use and
therefore might cause severe burns when touching bare skin. If provided, use handles when trying to
move this heater, or wait for the device to cool down.
Instructions for use
•Operation:
Only operate the heater in an upright position, following all the instructions and recommenda-
tions listed within this manual.
•Placement:
In order to achieve the maximum effect, place the heater in the area of the room that is coldest.
•Connection:
Directly connect the heater to a 230 V/50 Hz AC wall outlet. Be sure the plug fits tightly and
thereby properly into the outlet. A loose connection might cause the device to overheat and
thereby damage the plug and the heater.
Note: In order to prevent a circuit from overloading, do not connect the heater to a circuit that
is already strained by other electrical needs.
•Turning the device on:
First press the power control switch by setting it to either “I” (low) or “II” (high) before then rotat-
ing the thermostat knob clockwise until it reaches the setting for its highest temperature.
Note: During the initial use of the heater, a burnt smell might come out of the device. We would
like to assure you that this is normal and only a temporary condition caused by the last drips of
lubricant burning off the heating element. The unpleasant smell should disappear after a few
minutes.
•Power indicator:
When being turned on, the power indicator lamp of the heater will glow in order to indicate that
the heater is functioning.
•Power switch settings:
This heater has got two different heating settings and can either bet set to “I” (low) or “II” (high).
It is advised to use the “high” setting (1500 W) in order to quickly increase the temperature to
the desired level. Once the temperature desired has been reached, switch to the “low” mode,
which is sufficient for maintaining a comfortable temperature.

© by WilTec Wildanger Technik GmbH Item 61059 Page 5
http://www.WilTec.de
http://www.aoyue.eu 07 2021-1
http://www.teichtip.de
•Thermostat settings:
After the heater has been turned on and the room temperature has become comfortable, slowly
turn the thermostat knob counter-clockwise until the heater shuts off (a faint clicking noise
should be heard). By setting and leaving the thermostat like this, the device will automatically
maintain the current temperature. By further turning it counter-clockwise towards the “low” po-
sition, the temperature can be lowered. In order to raise the temperature, simply turn the knob
clockwise towards the “high” position.
•Turning the device off:
Turn the switch to the “off” position before plugging or unplugging the heater. Always make sure
to unplug the device while it is not in use.
•Fan mode:
Turn the power level control switch to the fan setting before turning the thermostat knob clock-
wise in order to make the fan run continuously.
Safety features
•The power indicator lamp of the device will be illuminated if either the fan or the heater are
turned on.
•The inbuilt overheating protection device will make sure to automatically turn off the device if
the heater grill is obstructed or the heater will grow too hot. Once the heater has been turned
off this way, it needs to be reset by turning it off and unplugging it. After waiting approximately
10 min in order for the device to cool down, the power cord can be reconnected and the heater
restarted.
•This product is equipped with a tip-over-switch, too, which causes the heater to automatically
shut down if it tips over. Simply place the device on an even surface without obstructions and
make sure that it is in an upright position in order to restart the heating process.
Maintenance
•Before cleaning the device make sure to unplug it and wait for the heater to cool down com-
pletely.
•A washable filter is located at the air inlet and can be removed in case it should require cleaning.
In case this filter should appear to be dirty, simply remove it from the device after unplugging
the same and making sure that it had cooled down. The filter can be rinsed with warm water,
but needs to have dried completely before it can be reattached to the filter.
•The outside of the heater can be cleaned with a damp piece of cloth while the device is un-
plugged.
•Do not use any detergents for this process and never dunk the heater in water as it is not only
going to destroy the device, but can also be dangerous. Once the frame has been cleaned,
make sure to let the device dry properly before putting it to use again.

© by WilTec Wildanger Technik GmbH Item 61059 Page 6
http://www.WilTec.de
http://www.aoyue.eu 07 2021-1
http://www.teichtip.de
Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were imple-
mented in the law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.
The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE-
registration number DE45283704.
Disposal of used electrical and electronic appliances
(intended for use in the countries of the European Un-
ion and other European countries with a separate col-
lection system for these appliances).
The logo on the article or on its packaging points out
that this article must not be treated as normal house-
hold waste but must be disposed to a recycling collec-
tion point for electronic and electrical waste equipment.
By contributing to the correct disposal of this article you
protect the environment and the health of your fellow
men. Environment and health are threatened by inap-
propriate disposal.
Material recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal waste
disposal facilities or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.