Windsor Design 61488 Assembly instructions

Page 2 For technical questions, please call 1-800-444-3353. Item 61488
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 3
Setup .......................................................... 3
Parts List and Diagram............................... 6
Warranty ..................................................... 8
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in serious injury.
Save all warnings and instructions for future reference.
1. Do not exceed weight capacities for the
Workbench shelves and drawers. Be aware of
dynamic loading! Sudden load movement may
briefly create excess load causing product failure.
2. Use only on flat, level and hard surface capable of
supporting the Workbench and any item(s) placed on
Workbench. Evenly distribute load to avoid tipping.
3. Use as intended only. Do not use Workbench to
perform task for which it was not designed.
4. For indoor use only.
5. Assemble only according to these instructions.
Improper assembly can create hazards.
6. Wear ANSI-approved safety
goggles during assembly.
7. Keep assembly area clean and well lit.
8. Keep bystanders out of the area during assembly.
9. Do not assemble when tired or when under
the influence of drugs or medication.
10. This product is not a toy. Do not allow children
to play with, on or near Workbench.
11. Inspect before every use; do not use
if parts are loose or damaged.
12. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact Harbor
Freight Tools for a replacement.
SAVE THESE INSTRUCTIONS.
SAFETY OPERATION MAINTENANCESETUP

Page 3For technical questions, please call 1-800-444-3353.Item 61488
Specifications
Maximum Weight Capacity
550 lb evenly distributed as follows:
Bench Top - 250 lb
Bottom Shelf - 200 lb
Each Drawer - 25 lb
Vise Capacity 7"
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding
the parts listed in the following pages, refer to
Parts List and Diagram on page 6.
Note: Finger tighten all connections until
assembly is done. Assemble the Workbench
on a flat, level, hard surface.
1. Insert Connecting Nuts (16) into Cross Braces (4) so
that the slots are horizontal and their holes line up
with the holes on the Cross Braces.
4
16
Slot
Figure A
2. Construct the Shelf Assembly by sliding the
Shelf into the grooves on the Cross Braces.
4
4
3
Figure B
3. Turn the Legs (6) upside down and attach the
Shelf Assembly to the Legs using Bolts (15).
15
15
15 15
6
6
Figure C
4. Lay the Table Top (1) upside down on
a flat, non-abrasive surface.
5. Attach the Drawer Support (7) using Screws (17).
7
17
1
Figure D
SAFETYOPERATIONMAINTENANCE SETUP

Page 4 For technical questions, please call 1-800-444-3353. Item 61488
6. Attach Legs with Shelf Assembly to
Table Top using Bolts (15).
15
15
Figure E
7. Attach the Lower Support (5) with Screws (17, 18).
8. Attach Legs with Screws (17).
17
18
17
17 17
17
17
5
Figure F
9. Turn Workbench right-side up. Remove the Bolt and
Washer (20) from the end of the Vise’s middle rod.
Bolt and
Washer (20)
10. Slide the Vise all the way into the
three holes on the Table Top.
11. From underneath, replace the Bolt and Washer
into the end of the Vise’s middle rod.
Figure G
12. Lay a Drawer Bottom (11) down on a flat surface,
felt side up. Slide the Drawer Bottom into the
grooves in the Side Drawer Panels (9).
13. Attach right and left Side Drawer Panels to the
Front (8) and Back (10) Drawer Panels with
Screws (17). Repeat for other Drawers.
8
9
9
11 10
17
17
17
17
Figure H
Note: Make sure all components are square and
level. Then, tighten all hardware securely.
14. Slide Drawers in, lining up the tracks on the
Drawers with the tracks in the Workbench.
15. Insert Wood (13) and Anvil (14) Pegs into
the holes on the Table Top as desired.
SAFETY OPERATION MAINTENANCESETUP

Page 5For technical questions, please call 1-800-444-3353.Item 61488
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general
condition of the table. Check for:
• loose hardware,
• misalignment or binding of parts,
• cracked or broken parts,
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces of
the Workbench with clean cloth.
SAFETYOPERATIONMAINTENANCE SETUP

Page 6 For technical questions, please call 1-800-444-3353. Item 61488
Part Description Qty
1Table Top 1
2 Vise 1
3 Shelf 1
4 Cross Brace 2
5 Lower Support 1
6Leg Assembly 2
7 Drawer Support 1
8 Front Drawer Panel 4
9 Side Drawer Panel 8
10 Back Drawer Panel 4
Part Description Qty
11 Drawer Bottom 4
12 Drawer Handle 4
13 Wood Peg 4
14 Anvil Peg 4
15 Bolt (M6x65) 14
16 Connecting Nut 8
17 Screw (3.5x35) 48
18 Screw (3.5x20) 2
19 Hex Key 1
20 Bolt (M6x15) and Washer 1
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
SAFETY OPERATION MAINTENANCESETUP

Page 7For technical questions, please call 1-800-444-3353.Item 61488
Assembly Diagram
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
1
3
4
6
6
15
15
15
15
18
19
17
17
17
17
16
10
11
12 8
9
7
14
13
2
4
5
16
17
15
17
17
17
17
17
SAFETYOPERATIONMAINTENANCE SETUP

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.