Wine Master SP40DU4 User manual

Installation and user manual
(please keep this document carefully)
Notice
d’installation et d’utilisation
S
P40DU4 / SP40DU
INDICATIONS STATED ON THE NAMEPLATE OF THE UNIT
oModel :
………………………………
oSerial N° :
…………………………
o
Purchase date :
………………………
Installation and user manual
(please keep this document carefully)
d’installation et d’utilisation
P40DU4 / SP40DU
INDICATIONS STATED ON THE NAMEPLATE OF THE UNIT
:
………………………………
…………………………
………………………
Réf : W2710
06
d’installation et d’utilisation
06
/2015

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 2
ser manual
Table of contents
1. TECHNICAL DATAS .................................................................................... 4
2. EQUIPMENT ............................................................................................... 6
2.1. Outside unit ....................................................................................................................6
2.2. Inside unit.......................................................................................................................6
2.3. Thermostat......................................................................................................................6
2.4. Wiring boxt .....................................................................................................................6
2.5. Connection drawing.....................................................................................................6
2.6. Cellar insulation ............................................................................................................7
2.6.1. Wall, ceiling and floor insulation .....................................................................................................8
2.6.2. The door ......................................................................................................................................................8
2.6.3. Insulation of other elements ..............................................................................................................8
3. INSTALLATION OF THE AIR CONDITIONER WINEMASTER
®
...................... 9
3.1. List of required material ............................................................................ 9
3.2. Installation of the outside unit .................................................................. 9
3.2.1. Wall drilling................................................................................................................................................9
3.2.2. Brackets installation ..............................................................................................................................9
3.2.3. Duct dismounting ....................................................................................................................................9
3.2.4. Fixing the outside unit.........................................................................................................................10
3.2.5. Cable dismounting ................................................................................................................................10
3.2.6. Air flow ......................................................................................................................................................10
3.3. Installation of the inside unit .................................................................. 11
3.4. Ducts reconnection .................................................................................. 11
3.5. Electric connection .................................................................................. 11
3.5.1. Wiring drawing .......................................................................................................................................12
3.6. Installation of the water drain system .................................................... 13
4. PLUGGING THE AIR CONDITIONER WINEMASTER
®
................................. 13
4.1. Connecting the air conditioner ................................................................ 13
4.2. Start up ................................................................................................... 14
4.2.1. Temperature setting.............................................................................................................................14
4.2.2. Standby mode .........................................................................................................................................14
4.2.3. Automatic defrost..................................................................................................................................14
5. MAINTENANCE OF THE AIR CONDITIONER WINEMASTER
®
..................... 15
5.1. Filter and outside unit cleaning ............................................................... 15
5.2. Condensate drain .................................................................................... 15
6. EXAMPLE OF INSTALLATION OF INSIDE UNIT ......................................... 16
6.1. Installation above the air conditioned room ............................................ 16
6.2. Installation beside the air conditioned room ........................................... 16
7. Warranty ................................................................................................. 17
7.1 Legal warranty .......................................................................................... 17
7. 2 years contractual warranty ....................................................................... 17
7.3 Warranty conditions ................................................................................ 17
7.4 Exclusions and limitations of warranty .................................................... 17
7. 17
F
GB

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 3
Introduction
You purchased an air conditioner WINEMASTER
®
and we thank you for your confidence.
From conception to marketing, everything has been implemented to offer an
exclusive and high quality product. Brainchild of a team who find in this a motivation to
ever satisfy you, we hope that your wine conditioning unit WINEMASTER
®
will bring you
great storage conditions and best wines aging for an incomparable pleasure.
Because the customer is at the heart of all our thoughts, we want to support you in your
first steps and lead you towards the best use of your air conditioner every day. Thus,
you will find in this manual technical information and practical advice to help you to deal
with the essential steps to installation and use.
In order that your wine tasting remains moments to share, WINEMASTER guarantees
you a sincere engagement, dedicated expertise and ongoing follow-up at your service!
WINEMASTER

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 4
1. TECHNICAL DATAS
WINESP40DU4 / WINESP40DU
Outside unit Inside unit
Weight of units 35 kg 26 kg
Dimensions H x L x D 408 x 596 x 415 317 x 638 x 546
Temperature setting
Preset at 12°C, adjustable between 4 & 15°C *
Maximum outside temperature.
40°C **
Cooling power
900 W at 15°C **
Electricity supply 230/240V-50 Hz
Cooling power 600 W
Heating power 500 W
Gas R404A
The circuit breaker must be at least 16 Amps.
* The insulation has to be in accordance with the volume of the cellar and the set temperature.
** The cooling performance is dependant from the outside temperature. Therefore, the set temperature
of 12°C for the cellar cannot be maintained if the outside temperature reaches the 40°C.
If the thermal safety functions to often, there is a risk for the compressor to be damaged. In all cases, it
must be avoid that the outside temperature remains at 40°C, this high temperature should be limited
to the summer period.
VENTILATED COLD OR « NO FROST »
The advantages of « ventilated cold »:
- No frost other than on the evaporator.
- Automatic defrosting and maximized refrigeration efficiency.
- Cold distribution improved by a permanent air circulation (without air stratification).
The circulation of air allows maintaining the pre-selected temperature throughout the cellar
- à la température présélectionnée.

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 5
Technical drawing
•Outside unit
FRONT SIDE
•Inside unit
FRONT SIDE
•Thermostat
FRONT SIDE
•Wiring box
FRONT SIDE

G UIDE D ' INSTALLATION ET D ’
UTILISATION
2. EQUIPMENT
The air conditioner is composed of 2 separate units, of a thermostat and a wiring box.
connected by frigorific ducting pipes and
distance between both units should not exceed
2.1.Outside unit
The unit must be installed outside or in a room.
If the unit is installed outside:
-
Place the unit in order the air suction and
-
Encourage the installation in open areas and sheltered from the sun
-
Be cautious to the noise to the neighborhood
-Raise the unit to prevent
from
If the unit is installed in a room :
-Place the
unit in order the air suction and air rejection are not disturbed
-
Ensure there is a good ventilation
-Maximum temperature
and non permanent
-Ideal temperature ≈ 20°C.
2.2.Inside unit
The inside unit is designed to be installed with a duct system. It has to be placed inside the
2.3.Thermostat
The thermostat can be installed either inside or outside the
The probe must always be placed in the air conditioned room. The supplied sensor has a length of 1,5m.
It can be extended using insulated flexible cable with 2 conductors of 0.5mm² minimum section.
2.4.Wiring boxt
The connection box can be installed too
into consideration the cable length ( 2 m)
2.5.Connection drawing
TAKE INTO CONSIDERAT
O TSIDE NIT
CABLE LENGTH E 5 or 9M
UTILISATION
WINESP40DU4 / WINESP40DU
The air conditioner is composed of 2 separate units, of a thermostat and a wiring box.
connected by frigorific ducting pipes and
electric connections t of 4 or 8m
depending the model
distance between both units should not exceed
4 or 8m.
The unit must be installed outside or in a room.
Place the unit in order the air suction and
air rejection are not disturbed
Encourage the installation in open areas and sheltered from the sun
Be cautious to the noise to the neighborhood
from
accumulation of water and snow
unit in order the air suction and air rejection are not disturbed
Ensure there is a good ventilation
and non permanent
≤ 40°C
The inside unit is designed to be installed with a duct system. It has to be placed inside the
The thermostat can be installed either inside or outside the
air
conditioned room
The probe must always be placed in the air conditioned room. The supplied sensor has a length of 1,5m.
It can be extended using insulated flexible cable with 2 conductors of 0.5mm² minimum section.
The connection box can be installed too
either inside or outside the wine cabinet.
into consideration the cable length ( 2 m)
TAKE INTO CONSIDERAT
ION THE CABLE LENGTH
S BETWEEN THE
CONNECTION BOX AND THE UNITS .
CABLE LENGTH
THERMOSTAT
CABLE LENGTH
2M
MAIN CONNECTION
NO CABLE S PPLIED
Page 6
The air conditioner is composed of 2 separate units, of a thermostat and a wiring box.
They must be
depending the model
. The
The inside unit is designed to be installed with a duct system. It has to be placed inside the
house.
conditioned room
.
The probe must always be placed in the air conditioned room. The supplied sensor has a length of 1,5m.
It can be extended using insulated flexible cable with 2 conductors of 0.5mm² minimum section.
.
either inside or outside the wine cabinet.
If installed outside, take
S BETWEEN THE
INSIDE NIT
CABLE LENGTH
2M

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 7
2.6.Cellar insulation
Insulation is essential for an efficient functioning of the WINEMASTER
®
. An appropriate insulation
enables to maintain a stable temperature and humidity level. The chart on the next page will allow
you to determine the type and thickness of insulation needed in relation to the exterior volume of the
cellar and the model of the WINEMASTER
®
, for an inside temperature of 12°C.
Insulation complement
The insulating elements should be preferably installed:
- By “tongue and groove “ panels or
- By fused together panels
IMPORTANT : Avoid heat and humidity intrusion which can alter their regulation
View
1. WALL
2. INS LATION MATERIAL
3. GRO ND LEVEL
4. FLOOR
5. CEILING
6. INS LATED DOOR
IMPORTANT
The WINEMASTER
®
warranty is only valid if the insulation is in compliance with the board « Insulation
selection » requirements for the whole cellar (walls, floor, door and ceiling) with perfect continuity of
insulation.
Insulation selection
Volume of
the cellar
(m³)
Polystyrene
expanded = 0,044
W/m°C
(mm)
Polystyrene
extruded
= 0,030 W/m°C
(mm)
Polyurethane foam
= 0,025 W/m°C
(mm)
4 20 10 10
8 30 20 20
12 50 30 30
16 60 40 40
20 80 50 50
24 90 60 50
28 100 70 60
32 120 80 70
36 140 90 80
40 150 100 90
If implementation of glass walls, the g value of the glazing should be a maximum of 1.0 W / m²K. In
addition, the glass surface cannot be greater than 50% of the total wall area of the air-conditioned room
2

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 8
2.6.1. Wall, ceiling and floor insulation
Type of insulation panels
You can select among the following type of panels:
- sual panels,
- « Complex panels »: insulation is covered with a with a cover material (plaster, mineral …..)
- « Sandwich panels »: insulation is covered on each side with a wooden panel or plaster board.
Important: The covering of the panels protects the insulation against damage and guarantees its
longevity. Avoid using mineral fibres insulation (glasswool, rockwool, etc…) as they may
accumulate moisture and lose their insulation power and avoid also thin film insulation
that are not
effective for cold.
DO YOU KNOW THAT ?
Some insulating materials are damaged by rodents. If necessary, cover the insulation with a protective
lining on the inside of the cellar to avoid presence of mouse or rats.
 Polyurethane is an insulator that, due to its chemical composition, is not attacked by the
rodents.
Floor insulation
The floor of the cellar must be able to support the shelves and the stored wine. Thus, it’s necessary to
choose insulation with adequate compression strength.
Improve the load capacity of the insulation (particularly under the shelve legs) by using :
- « Complex » insulation panels covered by panels of higher load capacity.
- Cover the insulation panel with a wooden panel (at least 15 mm thickness), or every other
appropriated material.
2.6.2. The door
Door improves the insulation. Two solutions are possible:
- Insulate an existing door with the same insulation materials used for the walls of the
cellar. Provide a tight seal between the door frame and all sides of the door with a strip of foam
rubber for example.
Use a specially design WINEMASTER isothermal door with polyurethane and a sealing foam
View 1. INS LATED DOOR
2. INS LATION
3. SEALING TAPE
2.6.3. Insulation of other elements
Avoid placing a wine cabinet or freezer who generates heat into the cellar. The central heating pipes
should be re-insulated during their passage through the cellar

G UIDE D ' INSTALLATION ET D ’
UTILISATION
3. INSTALLATION
OF THE AIR CONDITIONER
3.1.List
of required material
-
A cord 3G1.5mm² for the connection of wiring box
-Screws and tools
3.2.
Installation of the outside unit
3.2.1. Wall drilling
3.2.2.
Brackets installation
3.2.3. Duct dismounting
UTILISATION
WINESP40DU4 / WINESP40DU
OF THE AIR CONDITIONER
WINEMASTER
of required material
A cord 3G1.5mm² for the connection of wiring box
Installation of the outside unit
-
Trace and drill the 6 holes for fixing the
brackets as indicated
Brackets installation
-
nfold the brackets and fi
the supplied parts
-
nscrew and take the cover off
-
nscrew in order to release the holding
flange
Page 9
WINEMASTER
®
Trace and drill the 6 holes for fixing the
brackets as indicated
-
nfold the brackets and fi
x them with
the supplied parts
nscrew and take the cover off
nscrew in order to release the holding

G UIDE D ' INSTALLATION ET D ’
UTILISATION
3.2.4. Fix
ing the outside unit
3.2.5. Cable dismounting
3.2.6. Air flow
BLOWING
UTILISATION
WINESP40DU4 / WINESP40DU
-
se the 2 keys supplied with the unit
-
Maintain the le connection with key 1
and unscrew with key 2
-ATTENTION
:
unscrewing
during handling.
A slight
gas leak
ing the outside unit
-
Screw the 4 s anti
(supplied on the unit
-
Put the air conditioner on the brackets
-
Screw the 4 screw washer M6 using a
key of 10
-
nscrew the cable clamp 1 to release the
cable
-
nscrew the cover from the sealed box 2
-
nscrew and release the cable
S CTION
Page 10
se the 2 keys supplied with the unit
Maintain the le connection with key 1
and unscrew with key 2
:
Do not interrupt the
during handling.
gas leak
is normal.
Screw the 4 s anti
-vibrations pads
(supplied on the unit
Put the air conditioner on the brackets
Screw the 4 screw washer M6 using a
nscrew the cable clamp 1 to release the
nscrew the cover from the sealed box 2
nscrew and release the cable
S CTION

G UIDE D ' INSTALLATION ET D ’
UTILISATION
3.3.
Installation of the inside unit
Due to the diversity of wine cabinets and the type of locations, each
constraints of its installation.
Two decoration grids are supplied
with the unit.
3.4.Ducts reconnection
. You can now move
the ducts and cord
operations of §3.2.3.
CAUTION: The connectors
must be kept clean
the passage through the opening
s
3.5.Electric connection
The cables can be
disconnected from the
When connecting, be careful
to follow the
or numbers to corresponding pads .
The connecting box has to be connected to a single
16A.
THE UNIT HAS TO BE INSTALLED RESPECTING THE NATIONAL RULES OF ELECTRIC
S CTION
BLOWING
UTILISATION
WINESP40DU4 / WINESP40DU
Installation of the inside unit
Due to the diversity of wine cabinets and the type of locations, each
installer must adapt to the
-
se insulated ducting
- Make sure
to choose
have a length of
possible (14m
max
number of
elbow)
- Radius elbow
≥ 175 mm
-
Do not reduce the duct section
- The suction
and blowing
even partially
obstructed
-
The blowing and suction should be
separated to avoid a resumption of the air
supply, even partia
suction tempera
ture should be the same
as the room temperature when the unit
produces cold)
- Provide
openings
suction
and blowing
- Provide
space for
electrical connections and
the
condensate drain
with the unit.
These grids are adapted to the
the ducts and cord
through the openings
and reconnect the
must be kept clean
. It is highly
recommended to protect
s
.
disconnected from the
connection box for easy installation.
to follow the
§3.5.1 wiring diagram and
reconnect cables
The connecting box has to be connected to a single
phase power line p
rotected by a circuit breaker
THE UNIT HAS TO BE INSTALLED RESPECTING THE NATIONAL RULES OF ELECTRIC
INSTALLATIONS.
S CTION
Page 11
installer must adapt to the
se insulated ducting
Ø125mm
to choose
the perfect place to
the shortest ducting
max
/ reduce 1 m by
elbow)
≥ 175 mm
Do not reduce the duct section
and blowing
should in no way be
obstructed
The blowing and suction should be
separated to avoid a resumption of the air
supply, even partia
lly (for checking, the
ture should be the same
as the room temperature when the unit
openings
on the bottom for
and blowing
space for
refrigeration and
electrical connections and
the passage of
condensate drain
air flow .
and reconnect the
fittings using the inverse
recommended to protect
them during
reconnect cables
identified by letters
rotected by a circuit breaker
230V -
THE UNIT HAS TO BE INSTALLED RESPECTING THE NATIONAL RULES OF ELECTRIC

G UIDE D ' INSTALLATION ET D ’
UTILISATION
3.5.1. Wiring drawing
UTILISATION
WINESP40DU4 / WINESP40DU
Page 12

G UIDE D ' INSTALLATION ET D ’
UTILISATION
3.6.
Installation of the water drain system
!
THE T BE DRAIN SHO LD NOT BE
The condensate bucket may overflow if the drain
4.
PLUGGING THE AIR CONDITIONER
The thermostat indicates the temperature in the wine cellar with a precision of 2°C. A temperature
variation of the air doesn’t mean the same variation of the liquid due to the thermal capacity of the liquid.
The thermostat is set at 12°C in the factory. D
controlled and adjusted as indicated
(§4.2.1).
4.1.
Connecting the air conditioner
When you plug the unit to the electric socket, the display indicates the temperature of the wine
cabinet :
- If the
temperature is over the thermostat setting: the air conditioner starts running after 2
minutes.
-
If the temperature is under the thermostat setting: the compressor doesn’t start.
ventilator of inside unit works.
-
1
2
UTILISATION
WINESP40DU4 / WINESP40DU
Installation of the water drain system
-
The evacuation of the condensate is ma
drain pipe supplied with the unit
-Fit the drain pipe on the
bracket
supplied with the unit
-
The flow is done by gravity and must be connected to a
sewage or bucket that must regularly be emptied
-
THE T BE DRAIN SHO LD NOT BE
CLOOGED OR DO LOOP P!
The condensate bucket may overflow if the drain
is not directed downwards
PLUGGING THE AIR CONDITIONER
WINEMASTER
The thermostat indicates the temperature in the wine cellar with a precision of 2°C. A temperature
variation of the air doesn’t mean the same variation of the liquid due to the thermal capacity of the liquid.
The thermostat is set at 12°C in the factory. D
uring the installation, the set temperature must be
(§4.2.1).
Connecting the air conditioner
When you plug the unit to the electric socket, the display indicates the temperature of the wine
temperature is over the thermostat setting: the air conditioner starts running after 2
If the temperature is under the thermostat setting: the compressor doesn’t start.
ventilator of inside unit works.
Page 13
The evacuation of the condensate is ma
de through a
drain pipe supplied with the unit
bracket
(1) with a clamp (2)
The flow is done by gravity and must be connected to a
sewage or bucket that must regularly be emptied
is not directed downwards
WINEMASTER
®
The thermostat indicates the temperature in the wine cellar with a precision of 2°C. A temperature
variation of the air doesn’t mean the same variation of the liquid due to the thermal capacity of the liquid.
uring the installation, the set temperature must be
When you plug the unit to the electric socket, the display indicates the temperature of the wine
temperature is over the thermostat setting: the air conditioner starts running after 2
If the temperature is under the thermostat setting: the compressor doesn’t start.
Only the

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 14
4.2. Start up
4.2.1. Temperature setting
The setting of the targeted temperature is made on the thermostat:
- Press on one second until the targeted temperature is blinking.
- se to increase the temperature.
- se to lower the temperature.
- Once the right temperature is set, press on again to confirm.
Explanations on the main display symbols: :
Red light = cold more engaged (compressor working)
Red light = cooling fan on high speed
Red light = defrost
Red light = heating mode engaged (resistance)
4.2.2. Standby mode
- Standby mode: maintain 3 seconds on button 1. The compressor stops
and the fan turns at low speed.
- The thermostat indicates « OFF » and also the cellar temperature.
- To come back, maintain again a 3 seconds pressure on button 1.
- The thermostat indicates « ON » during 1 second
-
4.2.3. Automatic defrost
The program of the thermostat will run an automatic defrost time several times a day. During this
operation, the compressor is stopped, only the fan is functioning at low speed. The condensate water
produced during this period will be evacuated through the tube drain.

G UIDE D ' INSTALLATION ET D ’
UTILISATION
5. MAINTENANCE
OF THE AIR CONDITIONER
5.1.
Filter and outside unit cleaning
The outside unit is equipped with a washable and reusable filter
CHECK AND CLEAN THE FILTER REGULARLY



DUSTED FILTER = DAMAG
CHECK AND CLEAR THE OPENINGS



CLOGGED AIR INLET = DAMAGED AIR CONDITIONER
5.2. Condensate drain
Check and clean
the drain once a year.
UTILISATION
WINESP40DU4 / WINESP40DU
OF THE AIR CONDITIONER
WINEMASTER
Filter and outside unit cleaning
The outside unit is equipped with a washable and reusable filter
.

nscrew the 2 plastic screws (1)

Remove the filter cover (2)

Take the filter out (3)

Wash the filter with warm water

Once the filter cleaned and drained,
replace the filter
back and close the cover

CHECK AND CLEAN THE FILTER REGULARLY
DUSTED FILTER = DAMAG
E ON THE AIR CONDITIONER
CHECK AND CLEAR THE OPENINGS
REGULARLY
CLOGGED AIR INLET = DAMAGED AIR CONDITIONER
the drain once a year.
Page 15
WINEMASTER
®
nscrew the 2 plastic screws (1)
Remove the filter cover (2)
Take the filter out (3)
Wash the filter with warm water
Once the filter cleaned and drained,
back and close the cover
E ON THE AIR CONDITIONER

G UIDE D ' INSTALLATION ET D ’
UTILISATION
6. EXAMPLE
OF INSTALLATION OF INSIDE UNIT
6.1. Installation
above the air conditioned room
6.2. Installation
beside the air conditioned room
UTILISATION
WINESP40DU4 / WINESP40DU
OF INSTALLATION OF INSIDE UNIT
above the air conditioned room
beside the air conditioned room
Page 16

G UIDE D ' INSTALLATION ET D ’ UTILISATION WINESP40DU4 / WINESP40DU
Page 17
7. Warranty
The contractual warranty is not exclusive, earnings for the benefit of the purchaser profit of the legal
warranty against defects or hidden defects that applies under the conditions of article 1641 and following
from the civil code.
7.1 Legal warranty
The contractual warranty is not exclusive, earnings for the benefit of the purchaser profit of the legal
warranty against defects or hidden defects that applies under the conditions of article 1641 and following
from the civil code.
7. 2 years contractual warranty
WINEMASTER offers a 2 years warranty against any manufactured defect.
During this period of contractual warranty, WINEMASTER will replace any acknowledge defective part.
In case of electric failure, WINEMASTER reserves the right to check the appliance before replacing any
defective parts.
In case of refrigeration failure, WINEMASTER may require that the appliance is returned to the factory for
repair. Any interventions will take place according to the guidelines set in the ‘after sale service
document’.
Interventions and returns can only be done after written agreement from WINEMASTER after
sale service.
7.3 Warranty conditions
The contractual warranty applies to all appliance installed and used in conformity with this «user
manual ». His application is conditioned by the presentation of the purchase invoice or for lack of its
copy.
7.4 Exclusions and limitations of warranty
The warranty can be refused in following cases:
- Insulation of the cellar or installation of the appliance not in compliance with the instructions of this
guide.
- Damages due to negligence, lack of maintenance or incorrect use of the air conditioner
WINEMASTER
®
(particularly clogged filters.
- Exchange of parts or repair under warranty will not extend the 2 years warranty period.
WINEMASTER SAS cannot, in any case, be held liable for any direct or indirect damages resulting from
the failure of the air conditioner. The warranty is exclusively limited to the product itself.
The European Community is attaching a great importance to the environment and
the waste process, set up by a instruction N° 2002/96/CE relating to the electric and
electronic component waste (DEEE).
In accordance with this standard, the logo « crossed dustbin » is obligatory.
This logo means that the appliance may not under any circumstances be
thrown in the household garbage. It must be handed over to the appropriate
collection point for its treatment, recovery and recycling of wasted electric and
electronic components.
Acting like that, you make a gesture for the environment and contribute to the
safeguard of the natural resources as well as to the protection of human health.
7.